4" 7500psi Demco HP Mud Valve – Disassembly & Assembly Step‑by‑Step | HYRIG

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Conatct For Details
DetailReview(0)Additional

Product Brief
Step‑by‑step disassembly/assembly for 4" 7500psi Demco HP mud valve – largest and heaviest model: depressurize, remove handwheel, unbolt bonnet, extract stem and gate, remove seats and bushings. Inspect and replace worn parts using M8420-HP-MINOR or M8420-HP-MAJOR kits. Reassemble in reverse, HP hydrostatic test.

Full Description

Overview
The HYRIG 4" 7500psi Demco high‑pressure mud valve – the largest and highest pressure model in the DEMCO line – features a modular, top‑entry design that allows for complete inline servicing. Due to the extreme pressures and large component sizes (weighing approximately 350-450 lbs), special attention to safety, proper lifting, and torque procedures is essential. All replacement parts must be from the M8420-HP series – never use 5,000 PSI components in this HP valve.

Safety First – Extreme HP Precautions

  • Depressurize the system completely and verify zero pressure before valve disassembly.

  • Isolate the valve from all pressure sources with double block and bleed.

  • Wear appropriate PPE including impact‑resistant eye protection and heavy gloves.

  • Use proper lifting equipment (chain hoist or overhead crane) for heavy components (350-450 lbs).

  • Refer to API 6A high‑pressure safety guidelines.

Required Tools

  • Appropriate wrenches and socket sets (HP rated, up to 1-1/4")

  • Torque wrench capable of HP torque values

  • Soft‑faced hammer

  • HP seal installation tools

  • Cleaning materials and HP‑compatible lubricants

  • Lifting equipment (chain hoist or overhead crane)

Disassembly Procedure

Step 1: Preparation

  • Close the valve completely.

  • Depressurize and drain the line. Verify zero pressure.

  • Remove the handwheel assembly (M8420-HP-HANDLE).

  • Note: The bonnet assembly can be quickly removed for internal parts inspection.

Step 2: Bonnet Removal

  • Remove bonnet stud nuts (4 or 8 nuts, HP specification).

  • Use lifting equipment to carefully lift the heavy bonnet assembly (M8420-HP-05) straight up.

  • Remove the bonnet seal (HNBR).

  • Inspect bonnet and body sealing surfaces for damage or pitting.

Step 3: Stem and Gate Removal

  • Remove the stem screw.

  • Extract the oversized stem assembly (M8420-HP-03) with visual window.

  • Remove the thickened gate (M8420-HP-02) through the bonnet opening.

  • Note: The gate is a monolithic solid gate construction with T‑slot design, thickened for HP service.

  • Remove the stem packing (HNBR/Fabric).

Step 4: Seat and Seal Removal

  • Remove the large‑bore HP seat seal assembly (M8420-HP-04).

  • Extract the secondary seal.

  • Remove the retainer and screw seal.

Step 5: Bushing and Hardware Removal

  • Remove the HP bushing and explosion‑proof retaining ring set (M8420-HP-06).

  • Remove the grease fitting (STD-HP01) if replacement is needed.

  • Remove all HP fasteners for inspection.

Inspection Checklist (Extreme HP Specific)

ComponentInspection PointsAction if Damaged
BodyCracks, pitting, HP sealing surface damage, stress marksReplace or repair
BonnetCracks, seal groove damage, deformationReplace
Gate (M8420-HP-02)Wear, scoring, deformation under HP – check frequentlyReplace
Stem (M8420-HP-03)Bending, wear, thread damage, galling, window clarityReplace
Seats (M8420-HP-04)Wear, elastomer degradation, HP damageReplace
Seals (HNBR)Hardening, cracking, deformation – highest wear itemsReplace
Bushings (M8420-HP-06)Wear, scoring, HP stress marks – mandatory inspection at 6 monthsReplace
FastenersStretching, corrosion, thread damageReplace

Assembly Procedure (Reverse Order)

Step 1: Preparation

  • Clean all components thoroughly.

  • Inspect all sealing surfaces.

  • Apply HP‑compatible lubricant to all moving parts.

  • Have replacement parts ready (use M8420-HP-MINOR or M8420-HP-MAJOR kit).

Step 2: Seat and Seal Installation

  • Install new large‑bore HP seat seal assembly (M8420-HP-04).

  • Install new secondary seal.

  • Install new retainer.

  • Install new screw seal.

Step 3: Bushing and Hardware Installation

  • Install new HP bushing and retaining ring set (M8420-HP-06).

  • Install new grease fitting (STD-HP01) if replacing.

Step 4: Stem and Gate Installation

  • Insert the gate (M8420-HP-02) into the body.

  • Align the gate T‑slot with the stem.

  • Install the stem assembly (M8420-HP-03) – ensure the visual window faces outward.

  • Install new stem packing (HNBR/Fabric).

  • Install and tighten the stem screw.

Step 5: Bonnet Installation

  • Install new bonnet seal (HNBR).

  • Use lifting equipment to carefully lower the heavy bonnet assembly (M8420-HP-05) onto the body.

  • Install bonnet stud nuts.

  • Tighten nuts in star pattern to HP specified torque.

Step 6: Handwheel Installation

  • Install the handwheel assembly (M8420-HP-HANDLE).

  • Verify smooth operation.

Step 7: Post‑Service HP Testing

  • Perform hydrostatic test per API 6A requirements (test pressure: 11,250 PSI).

  • Cycle valve fully open and closed to verify smooth operation.

  • Check all seals for leaks under pressure.

  • Lubricate through HP grease fitting.

Critical Extreme HP Maintenance Tips

  • NEVER use 5,000 PSI rated parts in this HP valve.

  • Use only M8420-HP‑specified replacement parts.

  • HNBR is the only seal material – do not substitute NBR.

  • This model has the highest wear rate – inspect more frequently.

  • Document all maintenance activities for traceability.

For a detailed torque specification sheet, request one at info@hyrig.com.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit