4" 7500psi Demco HP Mud Valve Dimensions & Installation Guide | HYRIG

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Comprehensive dimensions and installation procedure for 4" 7500psi Demco HP mud valve. BW height 660mm, flanged 660mm height and 430mm width. RTJ flange 8‑7/8" bolts, R‑27 ring. Heavy-wall welding prep, orientation, torque, and hydrostatic testing.

Conatct For Details
DetailReview(0)Additional

Overview
Correct installation of the HYRIG 4" 7500psi Demco high‑pressure mud valve – the largest and highest pressure model in the DEMCO line – is critical to ensuring safe, leak‑free operation at extreme pressures. Due to the large size and weight of this valve (approximately 350-450 lbs), proper lifting equipment and careful handling are essential.

Valve Dimensions by Connection Type

ConnectionHeight (mm)Width (mm)
Butt-Weld (BW)660350
RTJ Flanged660430
Hammer Union660360

RTJ Flange Detailed Data

  • Flange O.D.: 292 mm

  • Bolt Quantity/Size: 8 bolts, 7/8" diameter

  • RTJ Ring: R-27

  • Bolt Circle: Standard API 6A high‑pressure dimensions

Butt‑Weld End Preparation

  • Schedule: XXH (Extra Extra Heavy)

  • Material: 4130 Alloy Steel compatible

  • Pre‑heat and post‑weld heat treatment (PWHT) required per API 6A

  • Prior to welding, the seat and bonnet seal must be removed from the valve body

Step‑by‑Step Installation Procedure

Step 1: Pre‑Installation Checks

  • Verify the valve size (4"), pressure rating (7,500 PSI), and connection type match your piping.

  • Inspect all sealing surfaces for transit damage.

  • Ensure the valve is in the fully closed position before installation.

  • Verify lifting equipment capacity for heavy valve (350-450 lbs).

Step 2: Orientation & Clearance

  • Install with the flow arrow pointing downstream.

  • For rising stem valves, provide adequate vertical clearance for full stem extension.

  • Ensure the large‑bore handwheel has clearance for full rotation.

Step 3: Connection‑Specific Mounting

  • Butt‑Weld (BW) :

    • Remove seat and bonnet seals before welding.

    • Use XXH schedule pipe with 4130 compatible material.

    • Apply pre‑heat and perform post‑weld heat treatment (PWHT) per API 6A.

    • Allow cooling before reinstalling seals.

  • RTJ Flanged :

    • Install RTJ ring (R‑27) in the groove.

    • Align flange bolt holes.

    • Install bolts (8 bolts, 7/8") and tighten in star pattern.

    • Torque to API 6A high‑pressure recommended values.

  • Hammer Union :

    • Align union halves.

    • Install HP O‑ring seal.

    • Tighten union nut with hammer wrench to API recommended torque.

Step 4: Post‑Installation Testing

  • Perform hydrostatic test per API 6A requirements (test pressure: 11,250 PSI).

  • Check all connections for leaks.

  • Cycle valve fully open and closed to verify smooth operation.

Step 5: Lubrication

  • Apply high‑pressure compatible grease through grease fitting (STD-HP01).

  • Use grease suitable for high‑pressure and high‑temperature service.

Critical Installation Notes

  • This is the largest and heaviest DEMCO mud valve model – use proper lifting equipment.

  • Do not use any 5,000 PSI rated components or seals in this 7,500 PSI valve.

  • For sour service (H₂S), ensure all materials are NACE MR‑01‑75 compliant.

  • Use only high‑pressure rated fasteners (B7/L7).

For detailed torque charts or installation troubleshooting, contact info@hyrig.com.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit