The KSB Sewatec and Sewabloc are single-stage, dry-installed volute casing pumps engineered for the toughest wastewater, sewage, sludge, and industrial effluent applications. Sewatec features a back pull-out design with bearing bracket, while Sewabloc is a close-coupled pump with flanged direct motor connection. Both series offer multiple impeller types, tandem mechanical seals, and a wide choice of wear-resistant materials – delivering high operating reliability, low maintenance costs, and maximum efficiency for municipal and industrial water management.
Versatile Impeller Designs – Five impeller types to match any fluid:
F / F-max: Vortex impeller – for solids-laden, viscous, gas-entrained media
E / E-max: Single-channel enclosed impeller – for solids and fibrous matter
D / D-max: Open diagonal single-vane / open radial multi-vane – for long-fibre mixtures
K / K-max: Multi-channel enclosed impeller – for contaminated solids-bearing non-gaseous fluids
Tandem Mechanical Seals – Two bi-rotational mechanical seals in series with reservoir; high operational reliability even under dry-running or difficult conditions.
Low Maintenance Bearings – Grease-lubricated, maintenance-free deep-groove ball bearings (permanently sealed) for smaller sizes; regreasable bearings for larger sizes.
Wear-Resistant Materials –
EN-GJL-250 (grey cast iron) for neutral, low-abrasion media
1.4517 / CD4MCuN (duplex stainless steel) for corrosive, chloride-containing effluents
EN-GJN-HB555 / XCR14 (white cast iron) for highly abrasive slurries (≥54 HRC)
Back Pull-Out Design (Sewatec) – Pump end removes without disturbing piping or motor; simplifies maintenance.
High Interchangeability – Standardized components shared with KSB Amarex KRT submersible pumps; reduces spare parts inventory.
Flexible Installation – Horizontal (baseplate, belt drive, direct coupling) or vertical (with elbow, pedestal, cardan shaft) configurations.
ATEX Compliance – Available for explosive atmospheres (on request).
| Parameter | F / F-max Impeller | E / E-max Impeller | D / D-max Impeller | K / K-max Impeller |
|---|---|---|---|---|
| Flow rate (Q) | ≤ 680 m³/h | ≤ 2,520 m³/h | ≤ 1,500 m³/h | ≤ 2,500+ m³/h |
| Head (H) | ≤ 80 m | ≤ 50 m | ≤ 80 m | ≤ 80 m |
| Fluid temperature | ≤ 70 °C | ≤ 70 °C | ≤ 70 °C | ≤ 70 °C |
| Operating pressure | ≤ 10 bar | ≤ 10 bar | ≤ 10 bar | ≤ 10 bar |
| Discharge size DN | 50 – 350 mm | 50 – 350 mm | 80 – 350 mm | 50 – 700 mm |
| Speed | 2900 / 1450 / 960 / 725 / 580 / 480 rpm (depending on pole number) |
Higher flow rates and custom hydraulics available on request.
| Component | Standard Material | Optional Materials |
|---|---|---|
| Casing | EN-GJL-250 | Duplex, White cast iron |
| Impeller | EN-GJL-250 | 1.4517, EN-GJN-HB555, 1.4462 |
| Wear plates | EN-GJL-250 | EN-GJN-HB555, 1.4517 |
| Shaft | 1.4021 | 1.4462 |
| Shaft sleeve | 1.4021 | – |
| Mechanical seal | SiC / SiC | – |
Municipal wastewater – raw sewage, activated sludge, digested sludge, nitrified sludge
Industrial effluent – chemical, petrochemical, food & beverage, pulp & paper
Surface water – contaminated rivers, rainwater, drainage
Sludge handling – untreated, digested, thickened sludge (up to 13% dry solids)
Abrasive media – sand, ash, scale, mine tailings (white iron version)
Corrosive fluids – seawater, brines, acidic wastewater (duplex version)
Flood control & irrigation – stormwater pumping stations