The semi-open impeller stainless steel centrifugal pump is specifically designed for applications where the pumped liquid contains soft solids, fibers, or moderate viscosity, yet higher efficiency than a fully open impeller is required. Unlike a closed impeller (which has front and back shrouds), the semi-open impeller has a back shroud but no front shroud. The impeller vanes run with a controlled close clearance to the pump casing (or replaceable wear plate). This design allows solids to pass through more easily than a closed impeller, while still achieving good hydraulic efficiency – typically 10‑15% higher than an open impeller.
Constructed entirely from stainless steel (304 or 316L), the pump offers excellent corrosion resistance, hygienic surface finishes, and long service life in aggressive environments. It is the pump of choice for food & beverage, pharmaceutical, chemical, pulp & paper, and industrial wastewater applications where product purity and solids handling are equally important.
| Impeller Type | Front Shroud | Back Shroud | Solids Handling | Efficiency | Typical Applications |
|---|---|---|---|---|---|
| Closed | Yes | Yes | Poor (clearances <1mm) | High (70‑85%) | Clean liquids, high head |
| Semi-open | No | Yes | Good (soft solids, fibers) | Medium‑high (60‑75%) | Food slurries, pulp, chemical transfer |
| Open (vane) | No | No | Excellent (large solids) | Low (45‑60%) | Sewage, heavy slurries, mining |
The semi-open impeller occupies the sweet spot: it handles soft solids up to 10‑15 mm (depending on pump size) and maintains an efficiency that keeps operating costs manageable.
| Parameter | Range |
|---|---|
| Flow range | 5 – 500 m³/h (22 – 2,200 GPM) |
| Head range | 5 – 80 m (16 – 260 ft) |
| Maximum solids size | Up to 15 mm (soft solids, fibers) |
| Viscosity range | Up to 500 cP (with derating) |
| Pressure rating | Up to 16 bar (standard) , 25 bar (HD option) |
| Temperature range | –20 to +150°C (–4 to +302°F) |
| Speed | 1,450 / 2,900 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz) |
| Material (wetted) | 304 SS, 316L SS (standard) , duplex (optional) |
| Impeller clearance adjustment | External shims or axial adjustment screw |
| Connections | Flanged (ANSI/DIN) or Sanitary (Tri‑clamp, SMS) |
| Surface finish | As cast, brushed, or electro‑polished (sanitary) |
| Component | Standard Material | Upgrade Option |
|---|---|---|
| Casing | 316L stainless steel (CF3M) | Duplex 2205, Super Duplex 2507 |
| Semi‑open impeller | 316L stainless steel | 17‑4 PH (hardened for abrasives) |
| Backplate / wear plate | 316L stainless steel | Stellite‑faced or tungsten carbide (for abrasives) |
| Shaft | 316 stainless steel (AISI 316) | 17‑4 PH, duplex |
| Mechanical seal | Carbon vs. ceramic (NBR) | Silicon carbide vs. silicon carbide (Viton/Aflas) |
| Casing gasket | EPDM (sanitary) or PTFE | Viton (FKM) , silicone |
For food, dairy, and pharmaceutical applications, the wetted parts are mechanically polished to Ra ≤0.8µm, and elastomers are FDA compliant. For chemical service, 316L with PTFE gaskets is standard.
Semi-open impeller design:
The impeller has a back shroud (closed on the back side) but open vanes on the front face.
Clearance between the impeller vanes and the casing wear plate is adjustable (typically 0.3‑0.5 mm).
This adjustable clearance allows the user to compensate for wear over time, maintaining efficiency.
Back pull-out design:
The complete rotating assembly (impeller, shaft, bearing housing, seal) can be removed from the casing without disturbing suction or discharge piping.
This simplifies maintenance, cleaning, and seal replacement.
Reversible wear plate:
The casing wear plate (or backplate) is often reversible or replaceable, extending pump life when handling abrasive slurries.
Sanitary options:
Quick‑disconnect clamps (Tri‑clamp) for hygienic piping
Self‑draining casing (no dead legs)
CIP (clean‑in‑place) capable design
| Service | Seal Faces | Elastomer | Flush Plan |
|---|---|---|---|
| Clean liquids, mild chemicals | Carbon vs. ceramic | NBR / EPDM | Plan 11 (self‑flush) |
| Hot water, light slurries | Silicon carbide vs. carbon | Viton | Plan 11 or Plan 21 |
| Corrosive chemicals | Silicon carbide vs. silicon carbide | Viton / Aflas | Plan 11 or external flush |
| Abrasive slurries | Tungsten carbide vs. silicon carbide | Viton | Plan 32 (external clean flush) |
| Food / sanitary | Carbon vs. ceramic (FDA approved) | EPDM / silicone | Plan 11 (with food‑grade coolant) |
Over time, abrasive wear increases the gap between the impeller and wear plate, reducing pump performance (head and flow). The semi‑open impeller allows easy clearance adjustment:
Loosen the locking nut on the shaft.
Turn the adjustment screw or add/remove shims to move the impeller closer to the wear plate.
Tighten the locking nut.
Proper clearance restores original hydraulic performance – a major advantage over closed impeller pumps where wear rings must be replaced.
| Industry | Typical Fluids | Why Semi‑open Impeller |
|---|---|---|
| Food & beverage | Fruit juices with pulp, beer mash, wine must, sauces, soups, edible oil slurries | Handles soft solids, easy to clean, corrosion resistant |
| Dairy | Cheese curds, yogurt with fruit pieces, whey with fines | Gentle on product, passes soft curds |
| Pharmaceutical | Suspensions, syrups with herbal particles, dental impression materials | Cleanable, smooth finish, no dead areas |
| Chemical | Latex, paints, adhesives, pigment slurries, polymer solutions | Good solids passage, corrosion resistance |
| Pulp & paper | Stock preparation (fibres), coating slurries | Handles fibre bundles without clogging |
| Wastewater | Industrial effluent with light solids, scum pumping | Passes small soft solids |
| Marine / desalination | Seawater with marine growth (algae, small shells) | Semi‑open design resists clogging, duplex option available |
Best efficiency point (BEP): Typically 60‑75%, depending on specific speed and solids content.
Head‑flow curve: Stable, continuously rising to shut‑off – suitable for parallel operation.
NPSHr: Slightly higher than closed impeller due to open front. For low NPSHa applications, use a larger inlet size or inducer.
Viscosity correction: For fluids >50 cP, de‑rate head, flow, and efficiency per Hydraulic Institute standards.
Passes soft solids and fibers – up to 10‑15 mm without clogging.
Higher efficiency than open impeller – saves energy while maintaining solids capability.
Adjustable clearance – restores performance after wear, extending pump life.
Corrosion resistant – 316L stainless steel wetted parts; ideal for acidic, alkaline, or salt‑laden fluids.
Hygienic options – polished surfaces, sanitary clamps, FDA elastomers.
Easy maintenance – back pull‑out design, replaceable wear plate, no wear rings to replace.
Wide temperature range – up to 150°C (302°F) with appropriate seal.
Back pull‑out design – maintenance without removing piping.
Cost‑effective – lower replacement part cost than closed impeller pumps (no complex wear rings).
Hydrostatic test: 1.5x maximum working pressure.
Performance test: Water at rated speed per ISO 9906 Grade 3 or API 610 Grade 2 (on request).
Material certification: EN 10204 3.1 for critical components.
PMI (Positive Material Identification): Available for 316L verification.
Surface finish test (sanitary): Ra measurement with profilometer.
Clean, high‑head applications (>150 m) – closed impeller is more efficient.
Very large or abrasive solids (>20 mm) – requires open impeller or vortex pump.
High pressure (>25 bar) – multistage closed impeller pump required.
Very low NPSHa (e.g., <2 m) – may cavitate; consider inducer or vertical pump.
| Component | Recommended Quantity |
|---|---|
| Mechanical seal kit (complete) | 1 set |
| Impeller (semi‑open) | 1 |
| Wear plate / backplate | 1 set |
| Gasket / O‑ring kit (full) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Shaft (optional) | 1 (for critical duty) |
For detailed selection of the correct semi‑open impeller stainless steel centrifugal pump – including fluid analysis (solids size, concentration, viscosity, corrosivity), material grade (304, 316L, duplex), mechanical seal selection, and sanitary or industrial configuration – please contact our engineering team.
Email: info@hyrig.com
Our engineers support food processing, chemical, pharmaceutical, and industrial slurry applications worldwide with reliable semi‑open impeller stainless steel pumps – efficient, cleanable, and built for solids‑handling.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.