Submersible Pump – API 610 VS / IEC for Deep Well, Sewage & Industrial Applications

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Submersible pump designed for operation fully submerged in the pumped liquid. Available in API 610 VS4 (wet pit sump) and VS6 (double casing diffuser) configurations for industrial service, plus standard wastewater and deep well models. Oil-filled or water-filled motor options. Handles clean water, sewage, sludge, seawater, and process liquids. Flows up to 10,000 m³/h, heads to 900 m, temperatures to 150°C. NACE MR0175 available. API 682 sealing.

Conatct For Details
DetailReview(0)Additional

Product Overview

A submersible pump is a centrifugal pump with a close-coupled electric motor that operates while fully submerged in the fluid being pumped. The entire assembly – pump and motor – is hermetically sealed and designed to operate underwater. Submersible pumps eliminate the need for suction lift, are self-priming by design, and are inherently quiet because the surrounding liquid dampens noise.

Submersible pumps are classified under two major standards:

  • API 610 (ISO 13709) for petroleum, petrochemical, and heavy industrial service – specifically VS4 (vertical suspended wet pit) and VS6 (vertical suspended double casing diffuser pump)

  • IEC / EN standards for water supply, sewage, drainage, and general industrial service

Our range covers both: standard submersible pumps for clean water, sewage, and drainage; and API 610 VS4/VS6 pumps for refinery sumps, offshore platform lift, seawater intake, and process applications requiring 20‑year design life and hazardous area compliance.

Submersible Pump Configurations – API 610 Classified

Within API 610, submersible pumps fall under the VS (Vertically Suspended) group, with two primary types:

Pump TypeAPI 610 DesignationConstructionTypical Application
VS4Vertical suspended, wet pit, single or multistage, diffuser typePump column with suction bell immersed in sump; motor at grade or submergedIndustrial sump drainage, refinery oily water sumps, pump pit evacuation
VS6Vertical suspended, double casing (can), diffuser pump, closed suctionOuter casing (can) surrounds the pump; motor on top discharge headSeawater lift, low NPSH applications, offshore platform caissons, deep well pumping

The VS4 is the most common for general sump and pit services. The VS6 is specified for low NPSH situations (the can provides a positive suction head) and for higher pressures.

Additionally, the following submersible pump types are widely used outside API 610:

  • Submersible sewage pump – single or multistage, vortex or channel impeller, solids handling (50–150 mm)

  • Deep well submersible pump – multistage, small diameter (4″ to 12″), for boreholes and water wells

  • Submersible slurry pump – heavy-duty, abrasion-resistant hydraulics for sand, gravel, mine dewatering

How a Submersible Pump Works

The motor is directly coupled to the impeller(s). Both are enclosed in a watertight housing. Power is supplied via a submersible cable with a water-blocking seal at the entry point. When started, the impeller rotates, creating low pressure at the eye, and liquid flows into the pump. The fluid passes through the impeller and diffuser stages (if multistage) and is discharged through the outlet. The surrounding liquid cools the motor – a critical design requirement – so the pump must never run dry.

Motor cooling is achieved either by:

  • Oil-filled motor – The internal space is filled with dielectric oil that transfers heat to the surrounding pumped fluid. Common in API 610 VS pumps and large sewage pumps.

  • Water-filled motor – Winding insulation is designed for direct water contact; the pumped water circulates through the motor for cooling. Used in many deep well pumps.

Key Technical Specifications

ParameterStandard Sewage / WaterAPI 610 VS4API 610 VS6Deep Well
Flow rangeUp to 1,000 m³/hUp to 750 m³/hUp to 840 m³/hUp to 300 m³/h
Head rangeUp to 80 mUp to 280 mUp to 900 mUp to 600 m
Pressure ratingUp to 10 barUp to 40 barUp to 110 barUp to 30 bar
Temperature range0–60°C–46 to +260°C–196 to +150°C0–50°C
Motor powerUp to 315 kWUp to 500 kWUp to 2,500 kWUp to 300 kW
Discharge sizes50–300 mm50–200 mm80–300 mm2″–12″
Solids handlingUp to 100 mmMinimal (clean service)Clean liquidsClean water
MaterialCast iron / SS304316L SS / Duplex316L SS / Super DuplexStainless steel / Brass

Materials – Standard and API 610 Table H

ComponentStandard (Water/Sewage)API 610 VS4/VS6 (Process)
Pump casing / bowlCast iron (GG25) or 304 SS316L SS (S-8), Duplex (D-1/D-2), CA6NM
ImpellerCast iron, bronze, 304 SS316L SS, Duplex, 17-4 PH
ShaftCarbon steel AISI 10454140 hardened, 316 SS, duplex
Wear ringsBronze or cast iron316L SS + Stellite / tungsten carbide
Motor housingCast ironStainless steel
FastenersZinc-plated steel / 304 SS316 SS / Duplex

For seawater lift (offshore platforms), super duplex (D-2, UNS S32750) with PREN >40 is required. NACE MR0175 / ISO 15156 available for sour service.

Mechanical Seals – API 682 and Submersible Specific

Submersible pumps use one of two sealing systems:

  1. Double mechanical seal with oil chamber – Two seals in series, separated by an oil-filled cavity. A probe detects water ingress. Standard on most industrial submersible pumps.

  2. Tandem seals with barrier fluid – For API 610 VS pumps, API 682 Arrangement 2 or 3 can be applied at the shaft penetration (discharge head). However, submersible motors often use proprietary seal systems that are not API 682 classified but are field-proven.

For submersible pumps that are fully submerged, the external seal sees only static water pressure; the critical seal is the lower seal keeping pumped liquid out of the motor.

Our API 610 VS pumps use API 682 cartridge seals at the discharge head (above grade) where the shaft passes through. For true submersible motor pumps, we use double mechanical seals with an intermediate oil chamber and moisture sensors.

NPSH and Submersion

Submersible pumps have an inherent NPSH advantage because the impeller is always submerged. However:

  • The required submergence (minimum liquid level above pump intake) must be maintained to avoid vortexing and air ingestion.

  • For VS6 can pumps, the can provides a constant flooded suction, eliminating NPSH issues.

  • For deep well pumps, the pump is set below the dynamic water level.

API 610 VS4 pumps used in sumps – ensure the suction strainer remains submerged at all times.

Motor Types and Cooling

Motor TypeCooling MethodApplications
Oil-filled (premium)Dielectric oil transfers heat to surrounding liquidAPI 610 VS pumps, heavy industrial, hot water, hydrocarbons
Water-filledPumped water circulates through motorDeep well pumps, clean water
Air-filled (dry motor in can)Motor in air-filled housing; heat conducted through casing to surrounding waterSmall drainage pumps, portable units

Oil-filled motors are preferred for high temperature and hazardous liquids because they provide better insulation and cooling.

Applications

IndustryApplicationRecommended Type
Oil & Gas – OffshoreSeawater lift from caisson to platform deckAPI 610 VS6 (super duplex)
Oil & Gas – OnshoreSump pumping, produced water transferAPI 610 VS4 (316L SS)
RefineryOily water sumps, API separator pitsAPI 610 VS4 (NACE, 316L SS)
Power plantCooling water intake from river/seaVS6 (duplex)
Municipal water supplyDeep wells, booster stationsDeep well submersible
Wastewater treatmentRaw sewage lift stationsSewage submersible (vortex impeller)
Mining / dewateringPit dewatering, slurry transferSubmersible slurry pump
ConstructionTrench dewatering, foundation drainagePortable submersible (dirty water)
Marine / shipBilge pumping, ballast transferSubmersible (Atex)

API 610 Compliance Highlights (VS4/VS6)

  • Design life: 20 years minimum

  • Continuous operation: Minimum 3 years uninterrupted service

  • Thrust bearing life: L10 ≥25,000 hours (in discharge head)

  • Critical speed: ≥120% of maximum operating speed

  • Hydrostatic test: Outer casing (VS6 can) or pump column tested at 1.5x design pressure

  • Performance test: Water per API 610 Grade 1 or 2

  • Material certification: EN 10204 3.1 full traceability

  • NACE MR0175 / ISO 15156 available for sour service

Why Choose Our Submersible Pump?

  • Versatile configurations – Sewage, clean water, deep well, API 610 VS4/VS6 for process industries

  • Solids handling – Vortex, channel, or multi-vane impellers for up to 100 mm solids

  • High efficiency – Hydraulically optimized stages for lowest life cycle cost

  • API 610 grade materials – 316L SS, duplex, super duplex, NACE MR0175

  • Reliable motor cooling – Oil-filled or water-filled, with thermal sensors and moisture detectors

  • Built-in protections – Seal leak sensors, winding temperature monitors, dry run protection

  • Easy installation – Guide rail systems for wet pits, direct flanged for deep wells

  • ATEX certified options – For hazardous area applications (Zone 1, Zone 2)

  • Global support – Spare parts and service centers worldwide

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal set (complete)1 set
Motor seal kit (oil-filled type)1 set
Upper and lower bearings1 set
Wear rings (if fitted)1 set
Gasket / O‑ring kit1 set
Moisture probe / seal sensor1

Get a Quote or Engineering Support

For selection of the correct Submersible Pump for your application – including duty point, solids content, submersion depth, fluid aggressiveness, hazardous area classification, and API 610 compliance – please contact our engineering team.

Email: info@hyrig.com

*Our engineers support municipal water, wastewater, mining, refinery, and offshore oil & gas projects worldwide with reliable submersible pumps – from standard sewage to API 610 VS4/VS6 process pumps.*


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit