JPIM SZJ-I Drilling Multi-Parameter Instrument

2026-01-07 17:32

SZJ-I Drilling Multi-Parameter Instrument

1 Technical Specifications:
1.1 Operating Temperature: -30°C ~ 70°C
1.2 Relative Humidity: 0% ~ 90%
1.3 Hook Load & Weight on Bit (WOB):
* Measuring Range: 0 ~ 5000 kN (0 ~ 500×10kN)
* Measurement Error: ≤ ±1.5%
1.4 Rotary Table Torque:
* Measuring Range: 0 ~ 40 kN·m (Display Scale: 0~500)
* Measurement Error: ≤ ±5%
1.5 Tong Torque (Represented as Tail Rope Pull):
* Measuring Range: 0 ~ 100 kN
* Measurement Error: ≤ ±2.5%
1.6 Standpipe Pressure:
* Measuring Range: 0 ~ 40 MPa
* Measurement Error: ≤ ±1.5%
1.7 Well Depth:
* Measuring Range: 0 ~ 9999.9 m
* Measurement Error: ≤ ±0.5%
1.8 Rotary Speed: Measuring Range: 0 ~ 300 RPM
1.9 Pump Stroke Speed: Measuring Range: 0 ~ 300 SPM
1.10 Mud Return Flow: Measuring Range: 0 ~ 100%
* Measurement Error: ≤ ±2%
1.11 Mud Tank Volume: 0 ~ 999.9 m³
1.12 System Operating Voltage: 220V AC ±20%, 47 ~ 63 Hz

2 Weight Indicator System
2.1 System Composition and Working Principle
The weight indicator system consists of a deadline anchor (horizontal or vertical type), a weight indicator gauge, a pressure transmitter, connecting lines, and cables. The weight sensor is a key component of the deadline anchor. It converts the deadline tension into a hydraulic pressure signal via a diaphragm squeezing hydraulic fluid, which is then transmitted to the weight indicator gauge and recorder.

The weight indicator gauge contains two bourdon tubes: one for gross weight (hook load) and one for a more sensitive reading (WOB). The pressure causes displacement at the free end of the bourdon tubes. This displacement is amplified via a linkage and bevel gear mechanism to rotate the pointer shaft, causing the pointers to deflect and indicate hook load and WOB. The short pointer is the weight pointer (yellow), and the long pointer is the sensitive pointer (red).

To acquire an electrical signal, the hydraulic signal is converted to a 4~20mA current signal by a pressure transmitter, typically installed inside the driller's console. The hydraulic signal from the weight sensor drives the pressure transmitter via a tee or cross fitting. The transmitter's output current signal is sent to the data acquisition unit via cable. Data including hook load and WOB is then transmitted to the LCD display on the drill floor via communication cable and to remote computers for display and recording via computer communication cable.

3 Rotary Torque Measurement System
3.1 Idler Wheel System Composition and Working Principle
For mechanical rigs (chain-driven rotary table), the torque measurement system consists of an idler wheel torque sensor, a rotary torque indicator gauge (inside the driller's display console), a pressure transmitter, connecting lines, and cables. The system indirectly measures rotary torque by measuring the tension in the tight side of the rotary drive chain. The sensor is installed beneath the tight side of the chain, with its idler wheel pushing up against the chain to create an angle. When torque is applied to the drill string, the chain exerts a downward force on the idler wheel proportional to the torque. This force generates hydraulic pressure within the sensor, which is transmitted via lines to the bourdon tube in the indicator gauge. The tube's free end displacement is amplified to drive the gauge pointer, indicating torque.

To acquire an electrical signal, the hydraulic signal is converted to a 4~20mA current signal by a pressure transmitter in the driller's console. The hydraulic signal from the idler sensor drives the transmitter via a tee. The output signal is processed by the data acquisition unit and transmitted for display and recording.

To measure torque in both forward and reverse directions, two identical idler sensors can be installed, connected to one or two indicator gauges. If only one gauge is used, manual switching between sensors is required. Key installation considerations are sufficient space inside the chain case and specifying the correct chain type/size (e.g., single or double strand, 2", 1.5", 1.75").

Idler Wheel Torque Sensor Parts List

Item No.Part NumberDescriptionQty.
1SZJ-ZN.1-9Mounting Plate1
2GB32.1-88Bolted Pin M8×181
3GB32.1-88Bolted Pin M8×401
4SZJ-ZN.4.1Idler Wheel Assembly1
5SZJ-ZN.4-2Support Arm1
6SZJ-ZN.1A-5Pin Shaft1
7SZJ-ZN.4.4Piston Assembly1
8SZJ-ZN.1.8Bracket1
9GB825-76Eyebolt M121
10SZJ-ZN.1-16Spacer Ring1

3.2 Clamp-On Hall Effect Rotary Torque Sensor
For DC electric rigs, the system consists of a clamp-on DC Hall effect torque sensor and connecting cables. The Hall sensor clamps onto the main motor power cable (paying attention to current direction). Changes in motor current reflect applied torque. The system calculates the specific torque value based on the motor current vs. torque curve. Sensor power: +24VDC, output: 4~20mA. Connection cable can be 2-wire (no ground) or 3-wire (with ground), connected via a 4-pin aviation plug to the acquisition unit. For AC VFD rigs, it is strongly recommended to obtain a 4~20mA torque signal from the rig's electric control system for acquisition.

4 Standpipe Pressure Measurement System
4.1 System Composition and Working Principle
The system consists of a standpipe pressure sensor, a standpipe pressure indicator gauge (in driller's console), a pressure transmitter, connecting lines, and cables.

4.1.1 Rubber Cup Type Sensor: Mud pressure in the standpipe acts on hydraulic fluid via a rubber cup inside the sensor. This pressure is transmitted via lines to the bourdon tube in the indicator gauge, causing pointer deflection.

Rubber Cup Type Standpipe Pressure Sensor Parts List

Item No.Part NumberDescriptionQty.
1-Tapered Seat Connection1
2-Square Seal Ring1
3-Wing Nut1
4SZJ-LY.1-1Pressure Cap1
5SZJ-LY.1-2Cylinder Body1
6SZJ-LY.1-3Rubber Cup1
7JY248-4Adapter1
8SZJ-LY.1-4Protective Sleeve1
9JY248.2Self-Sealing Male Coupler1
10JY248-8Washer1
11SZJ-DN.1.4Hose Assembly1
12JY248-3O-Ring 12x2.41
13JY246.4.1Quick Connect Male Coupler1

4.1.2 Piston Type Sensor: Mud pressure acts on hydraulic fluid via a piston inside the sensor, transmitted to the indicator gauge. A key maintenance point is detecting and replacing worn piston seals (common if fluid is not fully filled).

Piston Type Standpipe Pressure Sensor Parts List

Item No.Part NumberDescriptionQty.
1-Tapered Seat Connection1
2-Square Seal Ring1
3-Wing Nut1
4SZJ-LY.1E-1Threaded Retaining Ring1
5SZJ-LY.1E-2Standpipe Pressure Cylinder Body1
6SZJ-LY.1E-3Piston1
7JY248-8Washer2
8JY248-4Adapter1
9JY248.2Self-Sealing Male Coupler1
10SZJ-LY.1-4Protective Sleeve1
11SZJ-DN.1.4Hose Assembly1
12JY246.4.1Quick Connect Male Coupler1
13JY248-3O-Ring 12x2.42
14SZJ-LY.1E-4Retaining Ring2
15GB3452.1-82O-Ring 34.5×3.551

For electrical signal acquisition, a pressure transmitter converts the hydraulic signal to 4~20mA. The signal is processed and transmitted for display and recording.

5 Tong Torque Sensor
5.1 System Composition and Working Principle
The system consists of a tong torque sensor, a tong torque indicator gauge (in driller's console), a pressure transmitter (25MPa), connecting lines, and cables. The sensor is installed on the tong tail rope. During make-up, a tension proportional to the make-up torque is generated in the rope. This tension acts via a piston on hydraulic fluid in the sensor, transmitted to the indicator gauge. When using a hydraulic power tong or casing tong, this sensor may not be needed; the line can be connected directly to the tong's hydraulic source.

Tong Torque Sensor Parts List

Item No.Part NumberDescriptionQty.
1SZJ-DN.1-1Lifting Eye1
2JY246.4.1Quick Connect Male Coupler1
3JY248-3O-Ring 12×2.41
4SZJ-DN.1-2Plug1
5SZJ-DN.1-3Pin Shaft1
6SZJ-DN.1.4Hose Assembly1
7GB829-88Set Screw M8×6×61
8SZJ-DN.1-5Piston1
9GB3452.1-82O-Ring 77.5×5.31
10GB3452.1-82O-Ring 34.5×3.551
11SZJ-DN.1-6Cylinder Body1
12SZJ-DN.1-7Piston Rod1
13SZJ-DN.1-8Adapter1
14JY246.2.6-8Washer1
15SZJ-DN.1-9Washer1
16-Wiper Seal 351
17SZJ-DN.1-10Bleed Screw1
182-010O-Ring 6.07×1.781

6 Depth Measurement System
6.1 System Composition and Working Principle
The system consists of a depth sensor and cable. Sensors are either drawworks-mounted or crown block-mounted. The drawworks type uses a photoelectric encoder on the drawworks shaft, outputting two channels of 90° phase-shifted pulses to the acquisition unit. The crown block type uses two proximity switches facing the crown block sheave. A set of metal plates (8~12) on the sheave passes the switches, generating the two pulse channels for acquisition.

7 Mud Return Flow and Tank Volume Measurement System
7.1 System Composition and Working Principle
Both systems use non-contact measurement with ultrasonic level detectors and cables. As the mud level in the return flow line or tank changes, the detector emits ultrasonic pulses reflected from the surface. The time-of-flight difference is converted to an electrical signal, processed, and output as a current signal (e.g., 4~20mA) to the acquisition unit for display on the driller's console and in the office.

Mud Return Flow Sensor Parts List

Item No.Part NumberDescriptionQty.
1SZJ-HLC.1Return Flow Line Box Assembly1
2SZJ-HLC.2Return Probe Assembly1
3GB5781-86Bolt M6x151
4GB93-87Spring Washer 61
5GB95-85Flat Washer 61

Mud Tank Volume Sensor Parts List

Item No.Part NumberDescriptionQty.
1SZJ-HL.2-2Special Nut1
2-Ultrasonic Level Gauge1
3FQN18-4ZAJ-CSelf-Sealing 4-pin Socket1
4SZJ-NJ.2Fixed Bracket1
5SZJ-NJ-1Movable Clamp Block1
6GB5781-86Bolt M16×651
7GB93-87Spring Washer 161
8GB95-85Flat Washer 161
9SZJ-NJ.3Probe Mounting Bracket1

Communication Box Assembly Parts List

Item No.Part NumberDescriptionQty.
1-7-pin Socket1
2SZJ8.6-1Waterproof Enclosure1
3SZJ-DBS.1Power Supply1
4SZJ8.6-3Mounting Bracket1
5-Cable Gland PG111

Section 2: YTA-6H Intelligent Anti-Collision Control System

1 Main Technical Specifications
1.1 Braking Position Accuracy: Braking Height ±0.2m
1.2 Hook Height Display Range: -9.99 ~ 99.99 m
1.3 Braking Height Setting Range: 0.0 ~ 99.9 m
1.4 Hook Speed Display Range: 0.00 ~ 9.99 m/s
1.5 Overspeed Setting Range: 0.00 ~ 9.99 m/s
1.6 Max Load Setting Range: 0 ~ 999 tons
1.7 Load Display Range: 0.0 ~ 999.9 tons
1.8 Current Height Analog Display Range: 0~100% of set Anti-Collision Height
1.9 Warning Height: >90% of set Anti-Collision Height
1.10 Drum Wrap Layer Display Range: 0 ~ 9 layers
1.11 Drum Wrap Count Display Range: 0 ~ 99 counts
1.12 Traveling Block Reeving Display: 2/3, 3/4, 4/5, 5/6, 6/7, 7/8
1.13 Rig Status Indication: Hoisting; Lowering; Overspeed; Braking; Brake Failure; Overload
1.14 Hook Height Analog Display: LED Bar Graph Display
1.15 Digital Display: LCD Digital Display with Auto Backlight
1.16 Anti-Collision Brake Control Output: Normally open; outputs DC24V, 0.5A during braking
1.17 Intelligent Audio/Visual Alarm Output: DC24V, 0.5A (output during alarm)
1.18 Instrument Power Supply: DC24V
1.19 Instrument Power Consumption: <15W
1.20 Operating Temperature: -30°C ~ +60°C
1.21 Operating Humidity: 15% ~ 95% RH
1.22 Vibration Resistance: Max 2G, 2 hours per axis (X,Y,Z)
1.23 Protection Rating: IP65
1.24 Noise Immunity: 1000Vp-p, 1μs pulse width, 30–100Hz


Copyright: All rights reserved. Unauthorized reproduction is prohibited. HYRIG, Since 2007, Specializing in Oilfield Rig Spares.


How to Purchase

Contact: info@hyrig.com

Name:
Message:
Verification code:
Submit
Comment