Cementing Plugs Series | Top, Bottom & Non-Rotating Plugs

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the complete cementing plug series and spare parts. These plugs are essential for separating cement slurry from drilling mud, wiping the casing walls, and ensuring proper cement place
Conatct For Details
DetailReview(0)Additional

Key Facts

  • Plug Types: Top plugs, bottom plugs, non-rotating plugs, auto-latch plugs.
  • Drillability: PDC drillable materials (sizes 114.3 mm to 339.7 mm).
  • Elastomer Options: Available for water-based or oil-based drilling mud.
  • Special Designs: Anti-rotation features for reduced drill-out time.
  • Compatibility: Works with standard and non-rotating float equipment.

Cementing Plug Specifications

SeriesPlug TypeKey FeatureDrillabilityCompatibility
362Top PlugStandard plastic corded top plugPDC DrillableStandard float collars
366Bottom PlugSpecial bottom plug with diaphragmPDC DrillableStandard float collars
364Non-Rotating TopPlastic cord, anti-rotation teethPDC DrillableRequires non-rotating receiver plate
367Auto-LatchSelf-locking mechanismPDC DrillableAuto-latch float equipment

Data source: Technical data table.

Dimensions

Cementing plug dimensions are matched to the casing ID.

Casing Size RangeAvailable Plug SizesFin Configuration
4-1/2" to 13-3/8"114.3 mm to 339.7 mmStandard or Special (for tapered casing)

Special plugs for tapered casing strings and large diameter plugs (larger than 339 mm) are available. Contact us for exact OD and length.

Structure / Working Principle

Cementing plugs are pumped down the casing string ahead of and behind the cement slurry.

  • Bottom Plug: Runs ahead of the cement. Once it reaches the float collar, pressure is applied to rupture its diaphragm, allowing cement to flow through into the annulus.
  • Top Plug: Runs behind the cement. It lands on the bottom plug (or float collar) with a solid seal, indicating that the cement has been fully displaced. Pressure is then held to test the float equipment.
  • Non-Rotating Design: For horizontal wells or long drill-out sections, standard rubber fins can cause the plug to spin during drill-out. The 364 Series incorporates anti-rotation teeth that interlock with a receiver plate on the float equipment, preventing rotation and speeding up PDC drill-out.

Cross-Reference & Replacement

Selecting the right cementing plugs depends on your mud system and float equipment:

  1. Mud System: Are you using oil-based mud (OBM) or water-based mud (WBM)? Ensure the elastomer is matched to the mud type.
  2. Drill-out Strategy: If using a PDC bit in a horizontal well, consider upgrading to the Non-Rotating 364 Series to prevent the plug from spinning.
  3. Float Equipment Compatibility: Non-rotating plugs require a compatible float collar/shoe with a matching receiver plate.
  4. Casing Size: Standard sizes range from 114.3 mm to 339.7 mm.

Applications

  • Primary Casing Cementing: Standard separation of mud and cement.
  • Horizontal & Extended Reach Wells: Non-rotating plugs reduce drill-out time and risk.
  • Tapered Casing Strings: Special plugs are available to navigate through changes in casing diameter.
  • Oil-Based Mud Systems: Specialized elastomers prevent swelling and degradation.

Pressure and temperature ratings are application-dependent. Verify the selected plug's integrity against your well's maximum anticipated differential pressure before installation.

Selection Support

Need to match a plug to your specific casing ID and mud system? Send us your casing program and mud type, and we will confirm the correct series and elastomer.

Frequently Asked Questions

Q: What is the benefit of a non-rotating cement plug?
A: Non-rotating plugs have teeth that lock into the float equipment, preventing the plug from spinning when drilled out with a PDC bit. This significantly reduces drill-out time.

Q: Do I need a special float collar for non-rotating plugs?
A: Yes. The float collar must be equipped with a non-rotating receiver plate to engage the teeth on the plug.

Q: Can I use these plugs with oil-based mud?
A: Yes. We supply rubber elastomers specifically designed for both water-based and oil-based drilling muds.

Q: What sizes are available?
A: Standard plugs are available for casing sizes from 114.3 mm to 339.7 mm. Special sizes for larger or tapered casing are available upon request.

Q: What is the typical lead time for cementing plugs?
A: Standard lead time is 3-4 weeks depending on the specific series and elastomer requirements.

Contact

For cementing plug series selection and spare parts support, contact HYRIG: info@hyrig.com

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit