The Crude Oil Transfer Pump is a heavy-duty centrifugal pump designed for transporting crude oil across refinery units, pipeline systems, tank farms, and oil gathering stations. Crude oil transfer applications require pumps that can handle variable viscosities, intermittent or continuous operation, and in many cases, abrasive or corrosive impurities (sand, chlorides, H₂S, CO₂). All pumps in this series are fully manufactured and certified to API 610 11th/12th edition (ISO 13709) standards, guaranteeing a minimum 3-year uninterrupted operation and a 20-year design life.
Based on hydraulic requirements (flow, head, pressure, and crude properties), the appropriate API 610 pump configuration is selected from OH2 (overhung, single-stage), BB3 (axially split, multistage, between bearings), or BB5 (double-casing barrel, multistage) types. The same pump platforms are also used for other high-energy refinery services such as tower feed and pipeline charge.
| Pump Type | Configuration | Best Crude Oil Service |
|---|---|---|
| OH2 | Overhung, centerline-mounted, single-stage | Low-to-medium head (≤250 m), low-to-medium flow (≤3,000 m³/h); tank farm transfer, crude unit charge booster, small pipeline segments |
| BB3 | Axially split, single casing, multistage, between bearings | Medium-to-high head (250–1,500 m), medium-to-high flow (up to 3,000 m³/h); main crude unit charge, refinery crude transfer, long-distance pipeline intermediate stations |
| BB5 | Double casing barrel, radially split, multistage, between bearings | Very high head (>1,500 m), very high pressure (up to 300 bar); crude oil pipeline mainline pumps, high-differential refinery crude transfer |
| VS4/VS6 | Vertical suspended (sump or can) | Low NPSHa crude transfer from storage tanks or sumps; fire-code restricted areas |
The OH2 pump is the workhorse for low-to-medium head crude oil transfer. Characteristics include:
Single-stage, overhung impeller, centerline mounting
Back pull-out design – rotating assembly removable without disturbing piping
API 610 bearing housing with oil bath lubrication, L10 bearing life ≥25,000 hours
Flow up to 3,000 m³/h (13,200 gpm), head up to 250 m (820 ft)
Temperature range –45°C to +260°C
Standard materials: Carbon steel (C-6) for light sweet crude; 316L SS (S-8) for sour or corrosive crude; duplex for high-chloride crude
Ideal for tank farm suction/discharge, crude unit preheat train booster, and short-distance pipeline transfer.
For higher head requirements where single-stage OH2 is insufficient, BB3 offers:
Horizontally split single casing, between bearings, multistage (3 to 14 stages)
Removable upper casing half allows full rotor access without disturbing piping
Opposed (back-to-back) impellers for axial thrust self-balancing – no balance disc or drum
Double volute casings balance radial thrust, extending bearing life
Flow up to 3,000 m³/h, head up to 1,500 m (4,900 ft), pressure up to 150 bar
Centerline mounting for thermal stability
The BB3 crude oil pump is widely used as the main crude charge pump in refineries, feeding crude from storage to the atmospheric distillation unit. It is also found in pipeline booster stations where intermediate pressure lift is required.
For very high-pressure crude oil transfer (such as long-distance crude pipelines or high-pressure hydrotransport), the BB5 barrel pump provides:
Double-casing construction – outer barrel contains process pressure; inner assembly (cartridge) withdraws for maintenance
Radially split, between bearings, multistage (up to 16 stages)
Diffuser-type stage design for high efficiency and low radial loads
Flow up to 1,400 m³/h (6,160 gpm), head up to 2,600 m (8,500 ft), pressure up to 300 bar (4,350 psi)
Temperature up to 250°C (higher with special materials)
Preferred for crude oil pipeline mainline pumps and high-pressure refinery crude transfer
BB5 barrel pumps are also specified for other high-energy refinery services such as hydrocracker feed and residue charge.
| Parameter | Range |
|---|---|
| Flow | Up to 3,000 m³/h (13,200 gpm) |
| Head | Up to 250 m (820 ft) |
| Pressure rating | Up to 6.4 MPa (64 bar) |
| Temperature | –45°C to +260°C |
| Speed | 1,450 / 2,950 rpm (50 Hz) |
| Parameter | Range |
|---|---|
| Flow | Up to 3,000 m³/h (13,200 gpm) |
| Head | Up to 1,500 m (4,900 ft) |
| Pressure rating | Up to 15 MPa (150 bar) |
| Temperature | –45°C to +260°C |
| Stages | 3 – 14 |
| Parameter | Range |
|---|---|
| Flow | Up to 1,400 m³/h (6,160 gpm) |
| Head | Up to 2,600 m (8,500 ft) |
| Pressure rating | Up to 30 MPa (300 bar) |
| Temperature | Up to 250°C |
| Stages | Up to 16 |
Crude oil composition varies widely – from light sweet crude with minimal impurities to heavy sour crude containing sand, chlorides, H₂S, CO₂, and organic acids. Material selection must match the specific crude characteristics.
| Crude Type | API 610 Class | Typical Material | Remarks |
|---|---|---|---|
| Light sweet crude (low H₂S, low Cl⁻) | C-6 | Carbon steel (WCB / LCC) | Most economical, adequate for non-corrosive service |
| Sour crude (H₂S present) | C-6 with NACE MR0175 or S-8 | Carbon steel with NACE, or 316L SS | If H₂S meets NACE limits, carbon steel with sulfide stress cracking (SSC) resistance is acceptable; 316L SS provides added corrosion allowance |
| Crude with chlorides + H₂S | S-8 / D-1 | 316L SS or Duplex 2205 | Chlorides cause pitting and SCC in carbon steel |
| Heavy crude / acidic crude (TAN >1.0) | S-8 / D-2 | 316L SS or Super Duplex | High total acid number (TAN) requires stainless or duplex to resist naphthenic acid corrosion |
| Crude containing sand/abrasives | C-6 with hard wear rings | Carbon steel with Stellite facing | Erosion resistance through hardened wear rings and hard-coated impellers |
For crude oil pipeline pumps operating at high pressures, the outer casing (BB5) is typically low-alloy steel or carbon steel (Class II), with internal components (diffusers, impellers) specified in 316L SS (S-8) for corrosion resistance.
NACE MR0175 / ISO 15156 compliance is mandatory for crude oil containing H₂S above partial pressure limits. When specified, all pressure-containing and wetted parts must be certified for sour service.
Crude oil transfer pumps must contain the process fluid reliably to prevent leakage, fire hazards, and environmental release. Seal selection depends on crude properties (volatility, toxicity, particulates, temperature).
| Service | Recommended API 682 Seal | Plan | Notes |
|---|---|---|---|
| Light crude (low vapor pressure, non-H₂S) | Single cartridge (Type A) | Plan 11 / 21 | Self-flush from pump discharge |
| Light crude (volatile) | Single with quench | Plan 11 + Plan 62 | Steam quench to prevent atmospheric coke formation |
| Sour crude (H₂S) | Dual pressurized (Arr. 3) | Plan 53B | Zero emissions, bladder accumulator |
| Heavy crude / hot crude (>150°C) | Single bellows seal (Type B) | Plan 23 (cooled) | External cooling recirculation |
| Abrasive crude (sand) | Dual or single with clean flush | Plan 32 (external clean fluid) | Prevents solids from entering seal faces |
For crude oil pipeline mainline pumps (BB5), dual pressurized seals with Plan 53B are the industry standard, providing absolute containment and compliance with strict environmental regulations.
API 682 specifies that dual pressurized seals (Arrangement 3) must have barrier fluid pressure greater than process pressure, typically achieved with a bladder accumulator (Plan 53B) or a pressurised reservoir (Plan 53A).
Crude oil viscosity varies significantly. Lift and heavy crude at low temperatures can be viscous (100–1,000 cP). Centrifugal pump performance must be corrected for viscosity per HI (Hydraulic Institute) standards. The following penalties apply:
Flow reduction: 5–20% depending on viscosity
Head reduction: 10–30%
Efficiency reduction: 20–50% (significant energy penalty)
For viscous crude, it is common to:
Select a pump with a larger impeller diameter and reduce speed if viscosity is high
Specify heating (steam tracing or electric heat) on pump casing and piping to reduce crude viscosity at start-up
Confirm NPSHa at the lowest anticipated crude temperature (highest vapor pressure and viscosity) to avoid cavitation
Crude oil contains dissolved gases (methane, ethane, H₂S, CO₂). When calculating available NPSH, the fluid must be considered at bubble point at the pump suction temperature. Overestimating NPSHa (by assuming subcooling) is a common error leading to cavitation and impeller damage.
For crude transfer from atmospheric storage tanks, NPSHa is typically limited to 2–5 meters. A BB3 multistage pump with low-NPSH first-stage impeller (double-suction or inducer) may be required.
Crude oil transfer pumps must be protected from low-flow operation (below MCSF – Minimum Continuous Stable Flow). During start-up, shutdown, or low-demand periods, an automated recirculation valve (ARC) or a continuous recirculation orifice with bypass line returns minimum flow to the suction source (tank or surge drum).
| Application | Description | Recommended Pump Type |
|---|---|---|
| Refinery crude charge (main) | Pumping crude from storage tanks to crude unit preheat train and atmospheric distillation column | BB3 axially split multistage (high flow, high head) |
| Refinery crude booster | Low-head lift from tank farm to main charge pump suction | OH2 single-stage |
| Crude oil pipeline mainline | Long-distance crude transmission at high pressure (50–150 bar) | BB5 double-case barrel pump |
| Pipeline intermediate booster | Mid-line stations boosting pressure | BB5 barrel or BB3 axial split |
| Tank farm transfer | Loading/unloading from storage tanks to trucks, rail cars, or marine vessels | OH2 single-stage (low head, moderate flow) |
| Oil gathering station | Collecting crude from multiple wells and transferring to central processing facility | OH2 single-stage (duty depending on flow and head) |
| FPSO crude offloading | Transfer of crude from FPSO storage to shuttle tanker | BB3 or BB5 (head varies with offloading requirements) |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours (API 610 mandatory)
Critical speed: First lateral critical speed ≥120% of maximum operating speed
Centerline mounting: Required for process temperatures >150°C; recommended for all crude oil services to accommodate thermal expansion
Hydrostatic testing: Casing tested at 1.5x design pressure (maximum allowable working pressure)
Performance testing: Water performance test per API 610 Grade 1 or 2
Material certification: EN 10204 3.1 (full traceability for all pressure-containing and wetted parts)
Hydrostatic test – 1.5x design pressure
Performance test – Water, at rated speed (Grade 1 or 2)
Mechanical run test – Minimum 4 hours continuous operation
NPSH test – Full verification if specified
Material certification – EN 10204 3.1
Non-destructive examination (NDE) – MPI, dye penetrant, radiography, or UT per API 610
NACE MR0175 / ISO 15156 certification – For sour crude service (H₂S)
Full API 610 11th/12th edition compliance (ISO 13709) – 20-year design life, 3-year continuous run
Multiple configurations – OH2 (single-stage), BB3 (axially split multistage), BB5 (double-case barrel) covering all crude oil transfer duties from tank farm to mainline pipeline
Broad hydraulic coverage – Flows to 5,000 m³/h, heads to 2,600 m, pressures to 300 bar
Material flexibility – Carbon steel (C-6), 316L SS (S-8), duplex (D-1/D-2), super duplex, with NACE MR0175 sour service compliance
Opposed impeller (BB3/BB5) – Self-balancing axial thrust, no balance disc or drum maintenance
Diffuser or dual volute hydraulics – High efficiency and low radial loads across operating range
API 682 mechanical seal compatibility – Plan 11/21 for light crude, Plan 53B for sour/high-pressure service, Plan 23 for hot crude
Back pull-out (OH2) or cartridge (BB5) design – Reduced maintenance downtime
Centerline mounting – Maintains alignment during thermal cycling; essential for hot crude (>80°C)
Field-proven – Thousands of API 610 crude oil transfer pumps operating in refineries, pipelines, and production facilities worldwide
Spare parts kit (mechanical seal cartridge, bearings, wear rings, gaskets) recommended per pump
For BB5 barrel pumps: spare inner assembly cartridge reduces maintenance turnaround time significantly
Bearing inspection interval: 5,000 – 10,000 hours (depending on crude cleanliness)
Mechanical seal inspection: 8,000 – 12,000 hours (Plan 11/21); longer intervals for dual pressurized seals (Plan 53B)
Major overhaul: 20,000 hours or 3 years (whichever occurs first)
For detailed selection of the correct crude oil transfer pump for your specific application – including crude assay analysis (density, viscosity, H₂S, Cl⁻, TAN, sand content), hydraulic sizing (flow, head, NPSHa), material selection per API 610 Table H, API 682 seal plan determination (Plan 11/21 for light crude, Plan 53B for sour crude, Plan 23 for hot crude), and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support refinery crude charge, pipeline mainline, tank farm, and crude gathering projects worldwide with reliable API 610 crude oil transfer pumping solutions – from light sweet to heavy sour crude.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.