EAP‑I‑150‑500 – Complete Specifications & Dimensions
The EAP‑I‑150‑500 is a horizontal, single‑stage, single‑suction, centerline‑mounted (OH2) overhung centrifugal pump manufactured according to API 610 and GB/T 5656 standards. It is a very high‑capacity model of the EAP‑I series, positioned between the DN100 and DN200 sizes, designed for medium pressure (≤2.5 MPa) and medium temperature (-40℃ to +200℃) applications requiring large flow and moderate to high head.
Model: EAP‑I‑150‑500
Inlet DN: 150 mm
Flow Range: 180 – 2160 m³/h
Head Range: 30 – 320 m
Speed: 1450 r/min
Design Pressure: ≤ 2.5 MPa
Temperature Range: -40℃ to +200℃
Structure: OH2 (centerline‑mounted)
Seal Standard: API 682 (single mechanical seal)
Design Standard: API 610 (10th/11th/12th editions), GB/T 5656
Material Options: Carbon steel, 304/316 stainless steel
OH2 centerline‑mounted – uniform thermal expansion, minimal distortion at medium temperature
Back pull‑out overhung design – maintenance without removing suction/discharge piping or motor
Impeller with back vanes – reduces axial thrust, extends bearing life
Single volute casing – balances radial force, low vibration
Standard heavy‑duty bearings – reliable operation, easy replacement, low cost
API 682 seal compatibility – supports single mechanical seals for medium pressure services
Optimized hydraulics for high flow – wide high‑efficiency zone, excellent cavitation performance
Low speed (1450 r/min) – reduces wear, extends component life at high flow
EAP‑I‑150‑500 is a direct drop‑in replacement for:
Sulzer PRE 150‑500 (standard pressure variant)
Flowserve 3700 series (equivalent size)
KSB RPH / Etanorm API 150‑500
Goulds 3700 / 3900 150‑500
Ensival‑Moret OH2 standard pump
Same mounting dimensions, same hydraulic performance – no pipeline or foundation modification required.
Petrochemical – large‑scale conventional process transfer, main crude oil transfer, high‑flow solvent circulation, product transfer
Coal Chemical – main process water circulation, high‑flow medium‑pressure water supply
Energy & Power – large cooling water circulation, condenser cooling, heat exchange systems, medium‑pressure boiler feed
General Industry – industrial water supply for large plants, district cooling/heating circulation, irrigation
Water Treatment – large‑scale water distribution, high‑flow filtration feed, reverse osmosis pre‑treatment
Clean liquids, water, oil products, solvents
Neutral and weakly corrosive media
Trace particle‑containing media (≤0.5% solids by weight)
Suction flange: DN150 (6 inch) – Class 150 / 300 compatible
Discharge flange: DN150 (6 inch)
Baseplate mounting: Standard API 610 OH2 footprint
Shaft height: Matches Sulzer PRE and Flowserve 3700 equivalents
Coupling guard included
Q: What is the maximum flow of EAP‑I‑150‑500?
A: 2160 m³/h. For higher flows, see EAP‑I‑200‑500 (up to 2880 m³/h).
Q: What is the maximum head?
A: 320 meters at 1450 r/min. This is the highest head in the EAP‑I series for this flow range.
Q: Why is it only rated at 1450 r/min?
A: To handle high flow rates with lower NPSH requirement and longer component life. Low speed also reduces wear and noise.
Q: Can it handle temperatures above 200℃?
A: Standard design is -40℃ to +200℃. For higher temperatures, please refer to EAP9 series (up to 300℃) or EAPG series (up to 450℃).
Q: What is the maximum design pressure?
A: 2.5 MPa. For higher pressures (4.0/5.0/10.0 MPa) at similar flow ranges, see EAP9 or EAPG series.
Q: Does EAP‑I‑150‑500 directly replace Sulzer PRE 150‑500?
A: Yes. Identical installation dimensions and hydraulic performance.
Q: What mechanical seal is standard?
A: API 682 single mechanical seal. Double seals and seal plans (11, 21, 23, 52, 53A, 54) available on request.
Q: What materials are available?
A: Carbon steel (standard), 304 stainless steel, 316 stainless steel. For higher corrosion resistance, duplex or alloy materials available on request.
Q: What is the bearing life?
A: Over 17,500 hours under normal operating conditions.
Q: What is the lead time?
A: Standard lead time 4‑5 weeks. Express options available for urgent projects.
EAP‑I‑150‑400 (lower head, same flow range)
EAP‑I‑200‑500 (higher flow, similar head)
EAP‑I‑100‑500 (lower flow, similar head)
EAP9‑150‑500 (higher temperature & pressure version)
EAPG‑150‑500 (ultra‑high pressure version)
View all EAP‑I series models
API 610 compliance – reliable for continuous operation
OH2 centerline‑mounted – medium temperature stability
Back pull‑out design – reduced maintenance downtime
High flow capability – up to 2160 m³/h
Very high head – up to 320 m at large flow
Low speed (1450 rpm) – longer life, lower maintenance
Standard bearings – low cost, easy availability
Direct replacement for major international brands – no piping modifications
Cost‑effective solution for large‑scale medium pressure applications requiring high head
For price, datasheet, cross‑reference confirmation, or technical support:
Email: info@hyrig.com
Our engineering team responds within 24 hours with a quote and recommendations.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.