Garden Jet Pump – Self-Priming Ejector Pump for Home Water Supply & Irrigation

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Self-priming garden jet pump designed for domestic water supply, garden irrigation, and pressure boosting from shallow wells, tanks, or rainwater collection. Built-in ejector allows suction lift up to 8 meters. Compact design with cast iron or stainless steel casing, copper winding motor, and easy priming. Flows to 5 m³/h, heads to 50 m, power from 0.5 to 1.5 HP. Includes pressure switch and small tank for automatic operation.

Conatct For Details
DetailReview(0)Additional

Product Overview

The garden jet pump (also known as a shallow well jet pump) is a self-priming centrifugal pump equipped with an ejector assembly that enables it to draw water from depths up to 8 meters (25 feet) – making it ideal for shallow wells, rainwater tanks, cisterns, or surface water sources. Unlike standard centrifugal pumps that require a flooded suction, the jet pump can be located above the water source and will automatically prime itself, pulling water up from the supply.

This pump is the workhorse for domestic water supply, garden irrigation, lawn sprinkler systems, and pressure boosting applications where the water source is above ground level. Its compact design, quiet operation, and integrated pressure switch and small pressure tank allow automatic start/stop based on demand – providing convenience and water efficiency.

How a Garden Jet Pump Works

The jet pump uses a Venturi ejector to create suction:

  1. The motor drives an impeller, creating high‑velocity water flow.

  2. Part of this flow is diverted through a nozzle into the ejector, which creates a low‑pressure zone.

  3. The low pressure draws water up from the well or tank through the suction line.

  4. The two streams mix and enter the impeller eye, where the pump adds more pressure.

  5. Water is discharged to the house tap or garden hose.

Because the ejector is built into the pump housing (or mounted at the well for convertible jet pumps), the garden jet pump can self‑prime – clearing air from the suction line without manual filling.

Key Technical Specifications

ParameterTypical Range
Flow range1.5 – 5.0 m³/h (25 – 85 L/min)
Maximum head (pressure)30 – 50 m (100 – 165 ft)
Suction liftUp to 8 m (25 ft) – at sea level
Motor power0.5 – 1.5 HP (0.37 – 1.1 kW)
Voltage / frequency220‑240V / 50Hz or 110‑120V / 60Hz
Speed2,850 – 3,450 rpm
Inlet / outlet size1" × 1" or 1.25" × 1" (25mm or 32mm)
Maximum operating pressure4 – 5 bar (60 – 75 psi)
Liquid temperature0 – 40°C
Enclosure protectionIP44 (standard) , IP54 (optional)
Thermal protectionBuilt-in (auto-reset or manual)
Included accessoriesPressure switch, small pressure tank (2–5 L), pressure gauge, priming plug

Pump Configurations

TypeDescriptionBest Use
Standard jet pump (single-stage)Impeller + built-in ejector; compact and affordableGarden watering, small house supply (1 bathroom)
Two-stage jet pumpTwo impellers in series; higher pressure for taller houses or larger properties2–3 bathrooms, sprinkler systems
Convertible jet pumpEjector can be mounted at the pump (shallow well) or in the well (deep well up to 20 m)Dual‑purpose for future deeper wells

For most garden and small home applications, the standard single-stage jet pump is sufficient.

Construction Materials – Corrosion-Resistant

ComponentStandard MaterialUpgrade Option
Pump casing (volute)Cast iron with epoxy coatingStainless steel 304
ImpellerBrassStainless steel, engineering plastic (for mild water)
Ejector / diffuserBrass or engineered plasticStainless steel
Motor fan coverAluminium or steelStainless steel
ShaftStainless steel (AISI 304)AISI 316 (for aggressive water)
Mechanical sealCarbon / Ceramic / NBRSilicon carbide / Viton
FastenersZinc-plated steelStainless steel

Cast iron pumps are durable and have good heat dissipation. For portable or corrosive water applications (salt, high chlorine), choose the stainless steel version.

Self-Priming Performance

Suction Lift (meters)Priming Time (approx.)Flow Reduction
2 m20–30 secondsMinimal
5 m40–60 seconds~5%
8 m (maximum)90–120 seconds~15%
  • The pump must be placed as close as possible to the water source to minimise suction pipe length.

  • Suction pipe diameter must be at least the pump inlet size – larger pipe reduces friction and improves priming.

  • All suction joints must be absolutely airtight – a tiny air leak will prevent priming.

Pressure Switch and Automatic Operation

The garden jet pump comes factory-fitted with a pressure switch and a small diaphragm tank (2–5 litres). The switch is pre-set to cut in at 1.5 bar (22 psi) and cut out at 3 bar (43 psi) – adjustable.

How it works:

  • When a tap is opened, system pressure drops; the switch starts the pump.

  • Pump runs, supplying water until the tap closes and pressure reaches cut-out setting.

  • The pump stops and rests until pressure drops again.

The small tank prevents short cycling and absorbs water hammer.

Adjustable pressure range: 1.0 – 3.5 bar (higher on request). For systems with more than 3–4 fixtures, add an external pressure tank.

Installation Guidelines

  1. Location: Place the pump on a solid, level, dry surface, protected from rain and direct sun. Allow air circulation around the motor.

  2. Piping: Use rigid PVC or metal pipe for suction line. Keep suction pipe short (prefer <10 m), with as few elbows and fittings as possible. Slope suction pipe slightly upward to the pump.

  3. Foot valve (optional but recommended): Install a foot valve at the bottom of the suction pipe in the well or tank to keep the line filled when the pump stops.

  4. Priming: Remove the priming plug, fill the pump casing and suction pipe with water until full, then replace the plug. The pump will prime automatically on start-up if suction pipe is filled.

  5. Electrical: Connect to a dedicated circuit with a residual current device (RCD). Follow local electrical codes. Ensure motor rotation direction is correct (for three-phase models – check label).

  6. Pressure tank: The supplied small tank is adequate for light use. For heavy use, add a larger external tank.

Features

  • Self-priming – No foot valve required (though recommended). Priming is automatic after initial fill.

  • Quiet operation – Specially designed hydraulic and motor reduce noise for garden and home use.

  • Built-in thermal protection – Motor automatically shuts off if overheated (e.g., dry run). Auto-reset or manual reset depending on model.

  • Corrosion-resistant – Cast iron with epoxy coating or full stainless steel for long life.

  • Easy maintenance – Simple seal and impeller replacement; strainer on suction prevents debris entry.

  • Pressure gauge – Allows quick check of system performance.

  • Dry run protection (premium models) – Electronic sensor stops pump if water supply fails.

Applications

ApplicationDescription
Shallow well water supplyDraw water from wells up to 8 m deep for home use
Rainwater harvestingPump rainwater from storage tanks to garden hose or house
Garden irrigationWater lawns, flower beds, vegetable gardens via sprinklers or drip lines
Pressure boostingIncrease low mains water pressure to serve more fixtures
Car washingProvide pressurised water for hose and washer
Small farm / livestockWater troughs, small-scale spray irrigation

Why Choose Our Garden Jet Pump?

  • Easy to install and use – Clear instructions; priming only once; automatic pressure control

  • Reliable self-priming – Proven ejector design lifts water up to 8 m, clears air locks

  • Energy-efficient motor – Copper windings, low noise, high starting torque

  • Corrosion-resistant – Epoxy coating or stainless steel ensures years of service even with aggressive well water

  • Safety features – Thermal overload, IP44/IP54 motor, optional dry-run protection

  • Compact design – Small footprint suits garden, basement, or well house

  • Value package – Includes pressure switch, pressure tank, gauge – ready to install

  • Global voltage options – 110V/60Hz for North America; 230V/50Hz for Europe, Asia, Africa

  • 2-year warranty – Backed by responsive customer service

Maintenance Tips

TaskFrequencyInstructions
Clean inlet strainerEvery 3 monthsRemove debris from suction strainer (foot valve)
Check pressure tank air chargeEvery 6 monthsWith pump off, depressurise system; check air pressure (pre-charge 1.0–1.5 bar)
Inspect mechanical sealAnnually or when leakingReplace seal kit if water drips from shaft
Winterization (freezing climates)Before freezeDrain pump and piping completely; store indoors or heat-trace
Motor bearingsWhen noisyBearings are sealed – replace motor if noisy

Troubleshooting

ProblemLikely CauseSolution
Pump runs but no waterLoss of prime, air leak, empty wellRe-prime; check suction joints; install foot valve; wait for well recovery
Pump cycles on/off rapidlyLeak in system, pressure tank waterloggedRepair leaks; re‑pressurise tank air; replace tank if diaphragm failed
Low pressureClogged impeller, low voltage, air in lineClean impeller; check voltage; bleed air
Motor hums but won't startStuck impeller, bad capacitor (single-phase)Turn off power; clear debris from impeller; replace capacitor
Noisy operationCavitation (suction restriction), loose partsIncrease suction pipe size; check for blockage; tighten bolts

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal kit1 set
Impeller (complete)1
Diffuser / ejector1 set
Pressure switch1
Small pressure tank (2–5 L)1
Foot valve (1″ or 1.25″)1 (if not already installed)

Get a Quote or Engineering Support

For detailed selection of the correct garden jet pump for your well depth, water demand, and garden size – including suction lift calculation, pipe sizing, and pressure switch setting – please contact our engineering team.

Email: info@hyrig.com

Our engineers support home and garden water supply projects worldwide with reliable, self‑priming jet pumps – from shallow well supply to rain barrel irrigation.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit