Intelligent Pressure Booster System – Variable Speed Multi-Pump Skid for Constant Pressure Water Supply

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Intelligent pressure booster system – a complete variable frequency drive (VFD) controlled multi-pump skid that maintains constant discharge pressure regardless of flow demand. Automatically starts, stops, and stag pumps to match water consumption. Energy savings up to 50% vs. traditional on/off systems. Integrated controller, pressure sensor, small diaphragm tank, and up to 6 pumps. Flows to 500 m³/h, pressures to 16 bar. For high-rise buildings, hotels, hospitals, industrial plants, and district water supply.

Conatct For Details
DetailReview(0)Additional

Product Overview

An intelligent pressure booster system (also known as a variable speed booster set, multi-pump constant pressure system, or VFD water booster skid) is a complete, factory-assembled pumping unit that automatically maintains stable water pressure at a user‑set value – regardless of how many taps are open or how much flow is demanded. Unlike traditional fixed‑speed pumps that cycle on and off with pressure switches, causing pressure fluctuations and energy waste, the intelligent system continuously adjusts pump speed (and the number of running pumps) to match actual demand in real time.

The system consists of:

  • Two or more stainless steel multistage centrifugal pumps

  • One variable frequency drive (VFD) controller (lead pump) plus direct‑on‑line (DOL) starters (lag pumps)

  • A pressure sensor (4‑20 mA) mounted on the discharge manifold

  • A small diaphragm pressure tank (1‑8 litres) for system cushioning

  • A programmable logic controller (PLC) or dedicated pump controller with touchscreen interface

  • A stainless steel discharge manifold with isolation valves and check valves per pump

  • A common suction manifold (optional) and baseplate

The system is factory piped, wired, and tested – ready to connect to power, suction, and discharge piping.

How the Intelligent System Works

Single pump with VFD operation:

  • At low flow (e.g., single tap), the VFD runs the lead pump at low speed, maintaining constant pressure with minimal energy.

  • As flow increases, the VFD increases speed to maintain the same pressure.

  • When flow exceeds the capacity of one pump at maximum speed, the controller starts a second pump (lag pump) and balances the load between them (both VFD + DOL, or master‑slave VFD).

  • As flow decreases, the system stops lag pumps sequentially and finally slows the lead pump to sleep mode when no flow is detected.

Key benefits:

  • Constant pressure (±0.01‑0.02 MPa) – no pressure spikes or drops when demand changes.

  • Energy savings – typically 30‑60% compared to on/off systems, because pumps run at lower speeds most of the time.

  • Soft start – no current spikes, extending motor and pump life.

  • Automatic pump rotation (duty‑standby) – evens out wear across all pumps.

  • Automatic fault handling – if a pump fails, the system continues with remaining pumps.

Key Technical Specifications

ParameterRange
Number of pumps2 – 6 (standard) , up to 8 on request
Flow range (total)10 – 500 m³/h (44 – 2,200 GPM)
Pressure range2 – 16 bar (30 – 230 psi)
Pump typeVertical multistage stainless steel (304 or 316L)
Motor power per pump0.55 – 90 kW (0.75 – 120 HP)
Control methodVFD lead pump + DOL lag pumps, or multi‑VFD
Pressure sensor4‑20 mA, 0‑10 V, or HART
ControllerPLC with HMI (touchscreen) or dedicated pump controller
Communication protocolsModbus RTU, BACnet, Profibus, Ethernet/IP (optional)
Power supply380‑415V / 50Hz or 460V / 60Hz, three‑phase
Enclosure ratingIP42 (indoor) , IP54 (outdoor/weatherproof)
Diaphragm tank2 – 24 litres (pre‑charged)
BaseplateHeavy‑duty steel, epoxy coated

Pump and Material Selection

ComponentStandard MaterialPremium Option
Pump casing / impeller304 stainless steel316L stainless steel, duplex
Pump motorIE3 / IE4 efficiency, IP55IE5 permanent magnet
Manifold piping304 stainless steel316L stainless steel
Isolation valvesBall valve (304 SS)Butterfly valve (SS)
Check valvesSpring‑loaded, stainless steelSilent wafer type

For potable water, all wetted parts are certified to NSF/ANSI 61 or WRAS. For seawater or aggressive water, specify super duplex.

Control Modes – Flexibility for Any System

1. Constant pressure control (standard) – Set a fixed pressure (e.g., 4.5 bar). The system maintains that pressure at the discharge sensor point regardless of flow.

2. Proportional pressure control – Pressure setpoint varies with flow (lower pressure at low flow) to save additional energy. Used for high‑rise buildings where friction losses are significant.

3. Constant differential pressure – Maintains a fixed pressure difference across the system (e.g., across a control valve), used for district heating/cooling.

4. Schedule / time‑of‑day control – Different pressure setpoints for day and night (lower pressure at night to save energy).

5. Cascade control with feedforward – Uses incoming pressure measurement to adjust booster output (for mains pressure boosting).

System Features – Intelligent & User‑Friendly

FeatureBenefit
Touchscreen HMIReal‑time display of pressure, speed, flow, pump status, fault history
Automatic pump alternationChanges lead pump daily or hourly to equalise wear
Dry run protectionSystem shuts down if suction pressure falls below setpoint
Flow estimation (no flow meter)Calculates flow from pump speed and pressure – no separate flow meter needed
Sleep modeStops pump when no flow is detected; automatically restarts when a tap opens
Fault handlingAutomatically switches to next pump if a pump fails; alarms on screen
BSR (Building Management System) integrationModbus, BACnet, LON, or digital I/O for remote monitoring
Data loggingStores pressure, speed, runtime, fault history for analysis
Remote monitoring optionWeb or smartphone interface for system status and alarms

Energy Savings Analysis

A traditional on/off booster system (e.g., two pumps, pressure switch set to cut in at 3.5 bar and cut out at 5 bar) causes pressure to fluctuate between these limits, with pumps running at full speed whenever they are on. Average pressure is 4.25 bar, but the pumps draw full power for short periods, including frequent start/stop cycles.

An intelligent VFD system maintains precisely 4.5 bar continuously. The pump speed changes with demand. According to affinity laws:

  • Power is proportional to the cube of speed.

  • At 80% speed, power = 0.8³ = 0.51 (49% of full power).

  • A typical building with variable demand sees average speed of 60‑70% – energy savings of 50‑70% are realistic.

Simple payback for upgrading from an old on/off booster to an intelligent VFD system is typically 1‑3 years.

Applications

SectorTypical ApplicationPump QuantityPressure Range
High‑rise residentialDomestic water pressure boosting to upper floors2‑4 pumps4‑8 bar
HotelsConsistent shower pressure across all rooms3‑6 pumps4‑7 bar
HospitalsReliable water supply for clinical areas3‑6 pumps (duty/standby/standby)4‑8 bar
Schools / universitiesCampus water distribution2‑4 pumps3‑6 bar
Industrial plantsProcess water, wash‑down, cooling makeup2‑4 pumps4‑10 bar
District water supplyPressure boosting for housing estates4‑8 pumps (large flow)5‑12 bar
IrrigationGolf courses, agriculture2‑4 pumps5‑10 bar
Airport / transport hubsWater supply for terminals3‑6 pumps4‑8 bar

Installation Overview

  1. Foundation – Provide a solid, level concrete pad. The skid is bolted through vibration‑damping mounts.

  2. Suction connection – Connect to water source (tank, mains, or well). Install a strainer if debris is possible.

  3. Discharge connection – Pipe to the distribution system. Install a pressure relief valve set at 10% above maximum pressure.

  4. Electrical – Connect three‑phase power to the main controller cabinet. Use appropriate cable sizing. Ground all equipment.

  5. Pressure sensor – Installed on discharge manifold (factory wired). Ensure no blockages.

  6. Commissioning – Set desired pressure, ramp times, and sleep function via HMI. Test all pumps in manual and automatic modes.

Quality Assurance and Testing

  • Factory testing: Each system is filled with water, pressure tested, and run for 2 hours to verify control logic and stability.

  • Hydrostatic test of manifold: 1.5x design pressure.

  • Pump performance test: Water at rated speed per ISO 9906.

  • Control panel test: All I/O, alarms, communication verified.

  • Certifications: CE, UL (control panel optional) , CSA, and local electrical approvals.

Why Choose Our Intelligent Pressure Booster System?

  • Factory engineered and assembled – One source responsibility; no field integration of pumps, VFD, controller, and piping.

  • Energy savings of 30‑60% – Variable speed and automatic pump staging drastically reduce electricity bills.

  • Constant, stable pressure – No pressure fluctuations; comfortable for end users.

  • Reduced water hammer – Soft start and stop eliminates pipe shock.

  • Automatic fault tolerance – If one pump fails, the system continues with remaining pumps.

  • Low noise – Pumps run at slower speeds most of the time, greatly reducing noise.

  • Longer pump life – No frequent start/stop cycles; pumps run smoothly at optimum speed.

  • Easy remote monitoring – Modbus, BACnet, or smartphone app options.

  • Scalable – Add pumps later if demand grows; controller is programmable.

  • Proven technology – Thousands of systems installed worldwide in residential, commercial, and industrial applications.

Maintenance Schedule (Typical)

TaskFrequency
Check and clean pressure sensor port6 months
Inspect electrical connections and cooling fans12 months
Check air charge in diaphragm tank (with system depressurised)6 months
Check mechanical seal leaks on pumpsMonthly
Verify pump alternation and control logic12 months
Clean pump filters / strainers (if fitted)As needed

Recommended Spare Parts (Per System)

ComponentRecommended Quantity
Mechanical seal kit (per pump type)1 set per pump
Pressure sensor (4‑20 mA)1
Control board / I/O module (for controller)1
Fuses and contactor kit (per pump)1 set
Diaphragm tank (small, pre‑charged)1

Get a Quote or Engineering Support

For detailed selection of the correct intelligent pressure booster system – including number of pumps, flow and pressure requirements, pump materials, control options, BMS integration, and site electrical conditions – please contact our engineering team.

Email: info@hyrig.com

*Our engineers support high‑rise building, hotel, hospital, industrial plant, and municipal water boosting projects worldwide with intelligent, energy‑saving pressure booster systems – constant pressure, automatic, and built for 24/7 reliability.*


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit