LY series vertical long shaft submerged pump meeting API 610 11th Edition Type VS4. For urea melt (molten urea) transfer in prilling tower feed and granulation service. Single stage, single suction, volute type, radially split. Submerged impeller eliminates priming, steam jacket prevents crystalliza

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
LY series vertical long shaft submerged pump meeting API 610 11th Edition Type VS4. For urea melt (molten urea) transfer in prilling tower feed and granulation service. Single stage, single suction, volute type, radially split. Submerged impeller eliminates priming, steam jacket prevents crystallization, open impeller handles minor solids. Flow 2 to 2,600 m³/h, head 5 to 250 m, pressure to 5.0 MPa, temperature to +400°C (LYG up to +400°C). Materials: 304SS, 316L, duplex, copper‑free for urea service. API 682 mechanical seals.

Conatct For Details
DetailReview(0)Additional

The LY series is a vertical, single‑stage, single‑suction, volute type, radially split, long shaft submerged centrifugal pump manufactured in full compliance with API 610 11th Edition (ISO 13709) Type VS4. It is specifically designed for transferring molten urea (urea melt) in fertilizer plants, for prilling tower feed, and for granulation process.

The submerged design places the impeller and volute casing below the minimum liquid level in the melt pit or sump. This eliminates priming requirements, avoids suction lift issues, and ensures reliable start‑up even under low NPSH conditions.

Key Parameters (LY Series)

ParameterLY / LYO (Standard)LYG (High Temperature)
Flow rate2 – 2,600 m³/h (with advanced double‑volute for sizes ≥80mm)3 – 2,600 m³/h
Total head5 – 250 m16 – 250 m
Operating temperature-20°C to +120°CUp to +400°C
Design pressureUp to 1.6 MPa (standard), higher available up to 5.0 MPaUp to 1.6 MPa
Working pressureUp to 5.0 MPaUp to 1.6 MPa
Immersion depthUp to 7 m (standard; longer custom lengths available)Standard

Design Features

  • Submerged impeller with volute casing – pump always primed, no venting required at start‑up

  • Double volute casing (discharge sizes ≥80mm) – balances radial hydraulic forces, reduces shaft deflection and sliding bearing wear, extends service life

  • Steam jacket – integral heating jacket on casing and column pipe; circulates steam (≤0.6 MPa, up to 170°C) to maintain urea melt temperature above crystallization point and prevent solidification when pump is idle

  • Open impeller option – handles trace solids or minor deposits; semi‑open or enclosed impellers also available

  • Long line shaft with multi‑point bearings – uses sliding bearings inside column pipe and rolling bearings in bearing housing; external lubrication or self‑lubricating options; centralizers prevent shaft vibration in deep sumps

  • Rotor axial adjustability – adjustable nut allows precise clearance setting for optimal hydraulic efficiency

  • API 682 seal chamber (optional at discharge head) – no submerged dynamic seal, as impeller is fully submerged; single or double mechanical seals available for emission control if top seal is required

  • Discharge column – flanged sections for easy assembly and disassembly; separate discharge pipe construction eliminates leakage of pressurized liquid, shaft seal is not required in basic configuration

Materials of Construction

Urea solution and urea melt are moderately corrosive at high temperatures. Decomposition products (biuret, ammonia, carbamate) may increase corrosion. All wetted components shall be copper‑free to avoid material degradation.

ComponentStandard (Urea Melt)Upgrade
Volute casing304SS or 316L stainless steelDuplex 2205 / super duplex 2507
Impeller304SS or 316L (open for solids handling)Duplex / 12% Cr steel
Line shaftAISI 416 stainless steel17-4PH / duplex
Column pipeCarbon steel or 304SS (threaded / flanged)316SS / duplex
Discharge headCast iron / carbon steel (insulated)304SS / 316SS
Sliding bearingsPTFE‑lined bronze / rubber (water‑lubricated)Silicon carbide / carbon
Gaskets / O‑ringsPTFE or EPDMFFKM (Kalrez)

Seal & Flush Plans

  • Standard configuration: no submerged shaft seal – eliminates leakage path at the bottom

  • Top seal (if specified): single mechanical seal with Plan 11

  • Zero‑leak requirement: tandem seal Plan 52 (unpressurized buffer fluid)

  • Hazardous / toxic service (if ammonia or carbamate present): double seal Plan 53B (pressurized barrier fluid)

Auxiliary Systems

  • Minimum flow protection – automatic recirculation valve (ARC) recommended

  • Steam jacket – low pressure steam ≤0.6 MPa at ≤170°C; connections on casing and column pipe

  • Bearing cooling – water‑cooled bearing housing for hot urea melt (>120°C) recommended

  • Insulation – thermal insulation on discharge head and exposed piping

  • Casing drain – low point drain for safe pit maintenance

  • Casing vent – high point vent for startup air removal

  • Baseplate / mounting flange – heavy duty fabricated flange bolted to pit cover or concrete support

Applications

  • Urea prilling tower feed pump – from melt pit to prilling tower top

  • Urea granulation feed pump – from evaporator to fluid bed or drum granulator

  • Molten urea transfer – between storage tank and finishing units

  • Urea solution transfer – for dilution or blending service (with lower temperature limits)

  • High temperature chemical services – hot oil, molten sulfur, molten paraffin (LYG version)

Why Choose LY Series for Urea Melt?

  • Full API 610 11th Edition (ISO 13709) Type VS4 compliance – heavy duty, reliable performance

  • Submerged impeller design – no priming, no suction lift issues, excellent low NPSH performance

  • Steam jacket standard – prevents urea crystallization during idle periods

  • Submerged bearing with no shaft seal – eliminates leakage risk for high‑temperature molten urea

  • Copper‑free materials – suitable for urea and fertilizer melt service

  • Customizable shaft length – fits any pit depth up to 7 meters (longer on request)

  • China manufacturer – competitive pricing, 20‑28 weeks lead time for standard stainless steel

  • Factory testing – hydraulic performance, mechanical run, hydrostatic test

  • Spare parts – wear rings, bearings, shaft sleeves, steam jackets, gaskets available

For more information or a custom proposal for your urea melt pump (LY VS4) application, contact us at info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit