OFM 600 Triplex Plunger Pump Parts and Spares — Easy Wearing Parts

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
OFM 600 triplex plunger pump parts and spares for OFM Pump Inc well service operations. Easy wearing parts include valves, valve seats, valve springs, plungers 3.5 to 4.5 inch, plunger packing, stuffing box components, O-rings, seals, and fluid end parts. 600 BHP, 6 inch stroke, up to 20,000 PSI. OEM part numbers listed. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

The OFM 600 is a 600 BHP triplex single-acting plunger pump manufactured by OFM Pump Inc. (Odessa, TX, USA). The pump features a 6 inch (152.4 mm) stroke, a plunger diameter of 4.5 inches, a gear ratio of 4.68:1, and a maximum operating pressure of 6,288 psi (43.4 MPa). It is available in fully containerized Zone 2 offshore configurations with a Cummins N14 500 HP engine, Allison HT754 transmission, and DNV 2.7-1 lifting certification. The pump handles intermittent full-load operations including water injection, reverse circulation, well killing, acidizing, and cementing. Maximum flow rate is 13.2 BBL per min (19,000 bpd). Additional specifications from equipment listings show maximum pressure of 43.4 MPa and maximum flow rate of 35 L per s. Our OFM 600 pump parts and spares are manufactured to OEM standards and are 100 percent directly interchangeable with original parts, requiring no modification for installation.

Easy Wearing Parts for OFM 600 with OEM Part Numbers:

Valve Assembly and Components:

Valve — OEM Part No. 3102801276

Rubber Valve — OEM Part No. P106001985

Valve Seat — OEM Part No. 3102004973

Valve Seat — OEM Part No. 3102005195

Valve Spring — OEM Part No. 3102008919

Bushing for Valve Spring — OEM Part No. 3102008255

O-Ring for Valve Seat — OEM Part No. P100002674

Plungers and Packing:

4.5 inch Plunger — OEM Part No. 3102008250A

Packer Pack 4.5 inch — OEM Part No. P106000535

Seal Box — OEM Part No. 3102008263

Box for Stuffing Box — OEM Part No. 3102005199

Gland Clamping Ring — OEM Part No. 3102004987

Fluid End and Pressure Components:

Exhaust Presser Head — OEM Part No. 3102008260

Exhaust Gland Cover — OEM Part No. 3102008259

Suction Hold-Down Cover — OEM Part No. 3102008253

Suction Gland Cover — OEM Part No. 3102008257

Exhaust Flange — OEM Part No. 3102005172

Consolidation for BRS 2FIG1502 — OEM Part No. P220024059

Sensor Bushing — OEM Part No. 3102005201

Sensor Connection — OEM Part No. 3102005171

Seals and O-Rings:

O-Ring — OEM Part No. 3102004967

O-Ring — OEM Part No. P100002545

O-Ring — OEM Part No. P100002583

O-Ring — OEM Part No. P100002472

Face Sealing Ring — OEM Part No. P100002643

Gasket Ring for the Gland — OEM Part No. 3102004990

Sealing Clamping Head — OEM Part No. 3102005167

Fasteners and Related:

Hex Screw with Cylindrical Head — OEM Part No. D020023329

Cylindrical Pin — OEM Part No. D080008115

Hex Plug — OEM Part No. B070004686

Hydraulic Connection Bolt — OEM Part No. 3102005170

Hose Clamp Assembly — OEM Part No. 3102008269A

Mechanical Seal Pump — OEM Part No. 22451-1

Sleeve of a Shaft of the Pump Mission — OEM Part No. 20943-21

Materials and Construction:

Each OFM 600 part is made from materials selected for demanding high-pressure well service. Valve bodies and seats use forged alloy steel with advanced heat treatment for wear resistance and fatigue strength. Plungers use hardened surfaces with hard chrome plating for extended service life. Fluid end components are available in carbon steel and stainless steel, such as 4330V, 4330M, 17-4PH, and 15-5PH, with optimized geometry that reduces stress concentration at intersecting cavities. Seals use NBR, HNBR, or urethane compounds suitable for acid, frac, and standard service. The fluid end features a conventional valve-over-valve design and configuration that reduces maintenance time during on-site consumable changes. All parts are precision machined to OEM standards for 100 percent interchangeability.

Key Performance Advantages:

Our OFM 600 pump parts and spares offer high wear resistance, reliable sealing, and long service life. The fluid end is built in accordance with API Spec Q1 and ISO 9001 quality management systems for consistent quality and performance. The optimized fluid end geometry reduces stress concentration and extends fatigue life. All dimensions are strictly manufactured in accordance with OEM standards, achieving 100 percent direct interchangeability with original parts. No modification is required for installation, simplifying on-site maintenance and reducing pump downtime. Parts are compatible with water-based, oil-based, and synthetic service fluids.

Applications:

These parts are suitable for oilfield fracturing, cementing, acidizing, well killing, reverse circulation, water injection, and other well service operations. The OFM 600 pump unit is designed for Zone 2 offshore and land-based operations, including containerized configurations for remote and offshore locations.

Compatibility:

All listed parts are direct replacements for OFM 600 triplex plunger pump components. The OFM 600 fluid end is compatible in form and function with SPM TWS 600S, TWS 400, Gardner Denver, FMC, OPI, and SJS plunger pump models. Plunger sizes are available in 3 inch, 3.5 inch, 4 inch, and 4.5 inch to match specific pressure and flow requirements. No modification is required for installation.

Order Information:

MOQ: 5 pieces or sets, depending on the part. Custom materials, colors, and branding available. Standard export packaging. Delivery from stock or short lead time. For pricing, technical data sheets, or OEM inquiries, please contact us at info@hyrig.com

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit