The Permanent Magnet Intelligent Booster Pump represents the next generation of pressurised water supply systems, integrating three key technologies into a single compact unit:
IE5 permanent magnet synchronous motor – ultra-high efficiency across the entire speed range, achieving IE5 energy efficiency grade
Intelligent variable frequency controller – continuously adjusts motor speed to maintain constant discharge pressure regardless of flow demand
High-performance centrifugal pump stage – multi-stage or single-stage impeller design with optimized hydraulics
Unlike traditional booster pumps that operate at fixed speed and cycle on/off, the intelligent permanent magnet system automatically matches pump output to actual water demand. When a single tap is open, the pump runs slowly and quietly; when multiple outlets are used simultaneously, it accelerates to maintain stable pressure – eliminating pressure fluctuations and reducing energy waste.
This technology is applicable across a wide spectrum, from household water pressure boosting to high-end industrial process supply. For customers requiring a high-power industrial solution that fully complies with API 610 (ISO 13709) standards —the globally recognized benchmark for centrifugal pumps in the petroleum, petrochemical, and natural gas industries— the hydraulic end can be custom-engineered on API 610 OH2 or BB3 platforms with IE5 permanent magnet motor drive.
The system operates through a closed-loop control process:
Real-time pressure monitoring – a pressure sensor (typically 4-20 mA output) continuously measures discharge pressure
Intelligent algorithm processing – the built-in microprocessor compares actual pressure against the user-set target pressure
Variable frequency speed regulation – based on the deviation, the controller adjusts the PMSM motor speed via VFD technology
Constant pressure delivery – pump speed automatically increases or decreases to keep outlet pressure perfectly stable (±0.01 MPa accuracy) across all flow conditions
The IE5 permanent magnet synchronous motor features high power density (smaller frame size than induction motors for the same output), synchronous operation for precise speed control without slip, and significantly lower no-load losses. It achieves IE5 efficiency, the highest level defined by the IEC 60034-30-2 standard, delivering a dramatic improvement over traditional induction motors (IE2/IE3). This results in less heat generation, reduces cooling requirements, and extends bearing and motor life.
Energy savings are substantial – IE5 permanent magnet motors in variable speed pumping applications achieve 5-15% higher efficiency at rated load compared to asynchronous motors, with savings increasing to 20-40% at partial load conditions where typical booster pumps spend most of their operating life.
| Parameter | Standard Domestic/Commercial Range |
|---|---|
| Flow range | 1.5 – 7.2 m³/h (varies by model) |
| Head range | 17.5 – 50 m (varies by model) |
| Motor power | 0.2 – 1.0 kW (200 – 1000 W) |
| Motor efficiency | IE5 (permanent magnet synchronous) |
| Voltage / frequency | 220V / 50Hz (single-phase) , 3-phase 380V also available |
| Speed range | 2,000 – 5,200 rpm |
| Inlet / outlet size | DN25 (1″) |
| Maximum suction lift | Up to 8 m |
| Operating temperature | 0 – 90°C |
| Noise level | ≤47 dB (silent operation) |
| Protection class | IP55 |
| Control type | PID constant pressure control |
Technical reference (CA Series):
CA200: 1.5 m³/h (rated) , 3.5 m³/h (max) , 17.5 m (rated head) , 25 m (max) , 200W
CA200R: 1.5 m³/h (rated) , 3.8 m³/h (max) , 22 m (rated head) , 30 m (max) , 200W
CA600: 2.5 m³/h (rated) , 6.0 m³/h (max) , 25 m (rated head) , 45 m (max) , 600W
CA1000: 4.0 m³/h (rated) , 7.2 m³/h (max) , 35 m (rated head) , 50 m (max) , 1000W
For high-power, high-reliability industrial applications —such as those in oil & gas, petrochemical, or refinery services— the permanent magnet intelligent booster pump can be configured on an API 610 OH2 (overhung, centerline-mounted, single-stage) platform. With permanent magnet motor drive and VFD control, this configuration provides the same intelligent constant pressure benefits as the universal model, while also meeting the stringent verification standards of API 610.
Under the API 610 12th Edition (the latest standard released in January 2021), the hydraulic end is designed for demanding continuous duty and 20-year service life. The permanent magnet drive solution is compatible with over 130 hydraulic combinations available under the API 610 OH2 type, covering flows up to 3,200 m³/h and heads up to 480 m. The standard back pull-out design allows for simplified service without disturbing pipework. For low NPSH applications, an inducer is available to further extend the operating envelope.
API 610 12th Edition emphasizes improvements to reliability, safety, and environmental performance, while API 685 provides the specification criteria for sealless pumps (canned motor or magnetic drive) that deliver zero emission operation, making the permanent magnet synchronous motor a compatible choice for the most stringent environmental requirements.
This robust design, combined with high-efficiency permanent magnet technology, makes it suitable for pressurized supply, boiler feed, and chemical injection in process industries.
| Feature | Benefit |
|---|---|
| IE5 permanent magnet synchronous motor | Highest efficiency grade; significant energy savings across operating range |
| Intelligent variable frequency control | Constant pressure output regardless of flow variation; instant response to demand changes |
| Automatic sleep mode | Pump automatically stops when no flow is detected, reducing wear and energy consumption |
| Multi-tap simultaneous operation | Maintains pressure stability when several outlets are open at once |
| Ultra-quiet operation | Noise levels as low as 45 dB – suitable for noise-sensitive residential installations |
| Multiple built-in protections | Dry-run protection, over-temperature protection, freeze protection, over-current protection |
| Touchscreen panel (select models) | One-touch pressure adjustment; real-time fault display |
| Compact, all-in-one design | Pump, motor, controller and pressure tank integrated into a single footprint |
| Anti-corrosion construction | IP55 rated enclosure; rust-resistant shaft materials; long service life |
| Component | Material |
|---|---|
| Pump casing | Cast iron / Stainless steel (304/316) |
| Impeller | Brass / Stainless steel / Engineering plastic |
| Shaft | Stainless steel (anti-rust treated) |
| Mechanical seal | Imported brand (long-life, leak-proof) |
| Controller enclosure | IP55 – protected against dust and water jets |
Wetted parts comply with RoHS standards; no secondary water contamination.
For industrial models, API 610 Table H materials are available (carbon steel C-6, 316L stainless steel S-8, duplex D-1/D-2) with NACE MR0175 compliance for sour service.
Residential water pressure boosting – Homes, apartments, villas with insufficient mains water pressure
Commercial buildings – Small offices, hotels, schools, restaurants
Solar water heating systems – Circulation and booster duties
Air conditioning / HVAC – Cooling tower water circulation
Industrial water supply – Factory pressure boosting, wash-down systems
Reverse osmosis pre-treatment – Feed water pressure boosting
Garden and irrigation – Lawn sprinkler systems, drip irrigation
Boiler feed – Low-pressure boiler make-up water pressurization
Car wash systems – High-pressure wash bay supply
Traditional booster pumps operate at fixed speed, using pressure switches to turn the motor on and off. This results in pressure fluctuations, water hammer, and significant energy waste during start/stop cycles.
The permanent magnet intelligent system changes the paradigm:
Within the speed range of 30-100%, the IE5 motor efficiency stays consistently above 90%, whereas traditional induction motor efficiency falls sharply below 50% speed.
At 50% speed, pump power consumption theoretically reduces by a factor of 8 (affinity law), delivering near-silent operation and eliminating wasteful energy dissipation.
Total energy savings compared to traditional constant-speed pumps typically range from 20-40%, with simple payback periods of 1-3 years depending on local electricity costs.
Medium: Clean water or water with properties similar to clean water
pH range: 6.5 – 8.5
Solid content: ≤0.1% by volume; particle size ≤0.2mm
Ambient temperature: 0 – 40°C (standard); pump can handle liquids up to 90°C
Power supply: Single-phase 220V (±10%) or three-phase 380V
Suction lift: Up to 8 meters (ensure flooded suction for optimal performance)
For industrial applications with special media, please contact engineering for material compatibility and seal selection.
| Feature | PM Intelligent Variable Frequency | Traditional Constant Speed |
|---|---|---|
| Motor efficiency | IE5 (highest) | IE2 / IE3 |
| Speed control | Infinite (2,000-5,200 rpm) | Fixed (on/off only) |
| Pressure stability | Constant (±0.01 MPa) | Fluctuating (pump cycles) |
| Energy efficiency | 20-40% savings | Baseline |
| Noise level | ≤47 dB | 60-75 dB (noisy cycling) |
| Start/stop cycles | Reduces to near zero | Frequent – increases wear on seals, bearings, switches |
| Water hammer | None | Yes – pipes hammer when pump starts/stops |
| Intelligence | Self-diagnosing, constant pressure algorithm, fault alerts | None – only pressure switch |
| Protection functions | Comprehensive (dry-run, over-temp, overload, freeze, leak) | Limited |
Highest efficiency available – IE5 permanent magnet motor, achieving up to 96% motor efficiency
Intelligent constant pressure – No pressure tanks required; maintains stable pressure even when multiple taps open simultaneously
Ultra-quiet operation – Silent design enables installation in noise-sensitive environments such as kitchens, bathrooms, or living areas
Energy savings – Lower electricity bills, rapid return on investment
Longer component life – Virtually eliminates frequent start/stop cycling; reduces wear on seals, bearings, and switches
Comprehensive protection – Automatic shutdown under dry-run, over-load, over-temperature, or sensor failure
User-friendly interface – Touchscreen display (select models) for easy pressure setting and system diagnostics
Plug-and-play installation – Fully integrated system – no external controller or pressure tank required
| Component | Recommended Quantity (per pump) |
|---|---|
| Mechanical seal kit | 1 set |
| Controller (complete) | 1 set |
| Pressure sensor | 1 |
| Motor cooling fan | 1 (if applicable) |
For detailed selection of the correct Permanent Magnet Intelligent Booster Pump for your application – including flow/head analysis, installation conditions, and power supply requirements – please contact our engineering team.
Email: info@hyrig.com
Our engineers support residential, commercial, and industrial water boosting projects worldwide with intelligent IE5 permanent magnet booster pump solutions – energy efficient, whisper quiet, and built for reliability.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.