The horizontal multistage centrifugal pump is the industry standard for applications requiring very high discharge pressure – far beyond the capability of single‑stage pumps. By arranging multiple impellers in series on a single horizontal shaft, each impeller adds energy, and the total head is the sum of the individual stage heads (minus minor hydraulic losses). This design delivers high pressure while maintaining a compact footprint and stable operation.
All horizontal multistage pumps in this series are fully designed, manufactured and certified to API 610 11th/12th edition (ISO 13709) – the global benchmark for centrifugal pumps in petroleum, petrochemical, natural gas, and power generation industries. API 610 classifies horizontal multistage pumps into two primary configurations:
BB3 – Axially split, single‑casing, multistage, between‑bearings (horizontal, centreline mounted)
BB5 – Radially split, double‑casing (barrel), multistage, between‑bearings (horizontal, centreline mounted)
Both configurations are horizontal, providing superior stability, easy access for maintenance, and the ability to handle high temperatures through centreline mounting.
These pumps are built for a 20‑year design life and a minimum of 3 years of uninterrupted continuous operation – even under severe conditions of high pressure, high temperature, and corrosive or erosive fluids.
| Pump Type | Configuration | Best Application |
|---|---|---|
| BB3 (Axial Split) | Horizontally split single casing, between bearings, opposed impellers. Upper casing half removable without disturbing piping. | Boiler feed water (medium pressure), crude oil transfer, refinery process, water injection up to 150 bar, lean amine circulation. |
| BB5 (Barrel) | Radially split double casing (outer barrel + inner cartridge), between bearings, opposed or in‑line impellers. Outer barrel stays on baseplate while inner cartridge is withdrawn for maintenance. | Ultra‑high pressure boiler feed (supercritical), water injection (>150 bar), mainline crude pipelines, hydrocracker feed, high‑pressure reverse osmosis. |
The horizontal orientation offers several advantages over vertical multistage pumps: lower centre of gravity, easier alignment, simpler baseplate design, and better access for maintenance. Centreline mounting (feet cast on the horizontal centreline) ensures the pump casing expands uniformly with temperature, keeping the shaft aligned with the driver.
| Parameter | BB3 (Horizontal Axial Split) | BB5 (Horizontal Barrel) |
|---|---|---|
| Flow range | Up to 3,200 m³/h (14,000 gpm) | Up to 1,400 m³/h (6,160 gpm) |
| Head range | Up to 2,900 m (9,500 ft) | Up to 4,600 m (15,000 ft) |
| Pressure rating | Up to 150 bar (2,175 psi) | Up to 500 bar (7,250 psi) |
| Temperature range | –45 to +260°C (–50 to +500°F) | –45 to +450°C (–50 to +842°F) |
| Number of stages | 3 – 14 | 2 – 16+ |
| Maximum speed | Up to 6,000 rpm | Up to 6,500 rpm |
| Mounting | Centreline (horizontal feet) | Centreline (horizontal feet) |
| Casing split | Axial (horizontal) | Radial (vertical) |
In a horizontal multistage pump, fluid enters the suction nozzle and passes through the first stage impeller, where it gains velocity and pressure. It then flows through a diffuser or return channel that converts velocity to pressure and redirects the fluid to the eye of the next impeller. This process repeats through each stage. The total head is approximately the head per stage multiplied by the number of stages.
Opposed (back‑to‑back) impeller arrangement – impellers are mounted in opposing directions along the shaft, generating equal and opposite axial thrust that cancels itself hydraulically. This eliminates the need for a balance disc or drum, which can wear or foul. Opposed impellers are the standard for BB3 pumps and many BB5 pumps applied to low‑density fluids (e.g., lean amine, light hydrocarbons).
In‑line (all impellers facing same direction) – used in some BB5 pumps for high‑density fluids (e.g., water injection, boiler feed). Axial thrust is balanced by a balance drum or balance disc at the discharge end of the rotor, which creates a counteracting force.
BB3 double volute design – each stage incorporates a double volute casing that balances radial hydraulic forces, minimising shaft deflection and extending bearing life.
BB5 diffuser design – diffuser vanes surround each impeller, providing superior efficiency and much lower radial loads at off‑design (turndown) conditions. This is critical for water injection and pipeline service, where flow varies.
Both designs ensure that the rotor remains centrally aligned, reducing vibration and wear on wear rings and sleeve bearings.
Material selection for horizontal multistage pumps follows API 610 Table H, based on fluid corrosiveness, temperature, pressure, and abrasiveness.
| Component | Low/Medium Duty | High Duty / Corrosive | Extreme (Seawater / Sour) |
|---|---|---|---|
| Casing (BB3) | Carbon steel (C‑6) | 316L SS (S‑8) | Duplex (D‑1/D‑2) |
| Outer barrel (BB5) | Low alloy steel (forged) (Class II) | 316L SS clad | Duplex clad or solid super duplex |
| Inner casing / diffusers | Carbon steel or 304 SS | 316L SS (S‑8) | Duplex 2205 / 2507 |
| Impellers | Carbon steel / 304 SS | 316L SS (S‑8) | Duplex / Super Duplex (U‑8) |
| Shaft | 4140 hardened steel | 17‑4 PH SS | Duplex / Super Duplex |
| Wear rings | 4140 or 316 SS hard faced | 316L SS + Stellite | Duplex + Stellite / tungsten carbide |
| Balance drum (if fitted) | Hardened 4140 | Stellite‑clad 316L | Tungsten carbide / ceramic |
For boiler feed water – carbon steel or low alloy steel casings are common for moderate pressure (≤100 bar). For supercritical service (>250 bar), forged low‑alloy steel barrels with stainless steel clad internals are used.
For water injection (seawater or produced water) – super duplex (D‑2, UNS S32750) with PREN >40 is required to resist chloride pitting and H₂S cracking. NACE MR0175 / ISO 15156 certification is mandatory for sour water injection.
For refinery sour services – 316L SS (S‑8) with NACE MR0175 is the minimum.
Horizontal multistage pumps have two seal chambers – one at each end of the shaft (suction and discharge side). API 682 (4th edition) provides the standard for sealing. Seal selection depends on pressure, temperature, fluid hazard, and shaft speed.
| Service | Recommended Seal | API 682 Plan | Remarks |
|---|---|---|---|
| Boiler feed water (clean, <150°C) | Single seal (Type B, balanced) | Plan 23 (cooled recirculation) | Maintains low seal face temperature |
| Boiler feed water (high pressure, >150°C) | Tandem seal (Arr. 2) | Plan 52 | Buffer fluid collects leakage; safe for environment |
| Water injection (seawater, high pressure) | Dual pressurised (Arr. 3) | Plan 53B (bladder accumulator) | Zero emissions; barrier fluid > process pressure |
| Crude oil pipeline (sour) | Dual pressurised (Arr. 3) | Plan 53B | H₂S containment |
| Refinery charge (light hydrocarbon) | Tandem or dual | Plan 51/52/53B | – |
| High temperature (>200°C) | Single bellows seal (Type B) | Plan 23 or 62 | Quench for API Plan 62 if vapour at atmosphere |
Plan 23 is standard for boiler feed water – a cooling circuit recirculates fluid from the seal chamber through an external heat exchanger, returning cooled fluid to the seal, maintaining face temperature within limits.
Plan 53B uses a bladder accumulator to keep barrier fluid pressure above process pressure, guaranteeing zero leakage of hazardous fluid. This is mandatory for hydrogen sulfide (H₂S) service.
The first stage impeller is critical for NPSH performance. Horizontal multistage pumps are designed with:
Large eye, single‑suction impeller – standard for most duties, provides moderate NPSHr.
Double‑suction first stage – available for BB3 pumps where NPSHa is limited. The fluid enters from both sides of the impeller, reducing inlet velocity and NPSHr by approximately 30–40% compared to a single‑suction impeller of the same capacity.
Inducer – an axial flow stage mounted immediately before the first radial impeller. It increases pressure at the impeller eye, reducing NPSHr by 40–60%. Inducers are common in boiler feed pumps taking suction from a deaerator with only 3–5 meters of head.
Calculate NPSHa carefully. For hot water or light hydrocarbons, use vapour pressure at pumping temperature. Ensure NPSHa ≥ NPSHr + 1.0 m per API 610.
Operating a horizontal multistage pump below Minimum Continuous Stable Flow (MCSF) causes:
Recirculation at the impeller eye, leading to cavitation damage and vibration.
Temperature rise of liquid in the pump (especially in high‑head, low‑flow conditions), which can vaporise the fluid and destroy the balance device and seals.
Therefore, all horizontal multistage pumps must be equipped with a minimum flow recirculation system. Two common methods:
Automatically controlled recirculation valve (ARC) – senses flow and opens a bypass to the suction source when flow drops below setpoint. Energy efficient because recirculation occurs only when needed.
Continuous bypass orifice – a fixed orifice returns a constant minimum flow to the suction vessel, even during normal operation. Simpler but consumes energy continuously.
The recirculation line should return to a deaerator, suction tank, or reservoir – not to the pump suction pipe, as this would heat the inlet fluid and increase vapour pressure.
Horizontal multistage pumps use two main bearing types:
Radial bearings – journal (sleeve) bearings or anti‑friction roller bearings. Sleeve bearings are common in high‑speed BB5 pumps because they tolerate higher speeds and loads.
Thrust bearings – Kingsbury‑type tilting pad bearings or angular contact ball bearings, sized to handle residual axial thrust (after balance device).
Lubrication is typically oil mist (for refinery and pipeline) or forced oil circulation (for large power station boiler feed pumps). Bearing housings are designed for L10 life ≥25,000 hours per API 610.
| Industry | Application | Typical Configuration | Material |
|---|---|---|---|
| Power generation | Boiler feed water (subcritical) | BB3 or BB5 | Carbon steel / low alloy |
| Power generation | Boiler feed water (supercritical) | BB5 barrel | Forged steel + SS internals |
| Oil & gas | Water injection (onshore/offshore) | BB5 barrel | Super duplex (D‑2), NACE |
| Oil & gas | Crude oil pipeline mainline | BB5 barrel | Carbon steel (C‑6) or duplex |
| Refining | Crude charge to CDU | BB3 or BB5 | Carbon steel (C‑6) |
| Refining | Hydrocracker feed | BB5 barrel | 316L SS (S‑8) clad or duplex |
| Refining | Lean amine charge (high pressure) | BB3 or BB5 | 316L SS (S‑8) |
| Refining | Recycle gas compressor recycle | BB3 (low flow) | 316L SS |
| Petrochemical | High‑pressure process feed | BB3 | 304/316 SS |
| Desalination | High‑pressure reverse osmosis feed | BB5 barrel | Super duplex (D‑2) |
| Mining | Long‑distance slurry tailings (water) | BB3 | Duplex |
| Feature | Horizontal | Vertical (VS6) |
|---|---|---|
| Stability | Lower centre of gravity, less vibration | Higher centre of gravity, more susceptible |
| Maintenance | Easier access to bearings, seals, and rotor | Requires crane for motor and column removal |
| NPSH | Higher NPSHr (requires taller suction column) | Inherently low NPSH (submerged) |
| Footprint | Larger plan area | Smaller footprint |
| Thermal expansion | Centreline mounting handles expansion well | Column expansion must be accommodated |
| Cost | Lower for same head/flow (simpler construction) | Higher for high‑head because of long shaft |
For most high‑head, high‑power applications with adequate NPSHa, a horizontal multistage pump is the preferred choice.
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours
Critical speed: First lateral critical speed ≥120% of maximum operating speed
Centreline mounting (horizontal): Essential for high‑temperature services (>150°C)
Hydrostatic test: Pressure casing tested at 1.5x design pressure
Performance test: Water per API 610 Grade 1 or 2
NPSH test: Full verification when specified
Material certification: EN 10204 3.1 full traceability for all pressure‑containing and wetted parts
NACE MR0175 / ISO 15156 available for sour service
Hydrostatic test of outer barrel (BB5) and casing (BB3) at 1.5x MAWP
Performance test at rated speed, measuring head, flow, power, vibration, bearing temperature
Mechanical run test (minimum 4 hours) to verify smooth operation and no leaks
NPSH test (optional) using water with vacuum or gas content method
Noise and vibration testing per API 610 limits (Grade 1 or 2)
Non‑destructive examination (NDE): MPI, dye penetrant, or ultrasonic inspection per API 610
Material certification with EN 10204 3.1 full traceability
Full API 610 compliance (BB3 / BB5) – 11th/12th edition ISO 13709, 20‑year design life, 3‑year continuous run
Opposed impeller (back‑to‑back) option – self‑balancing axial thrust, no balance disc wear or maintenance
Double volute (BB3) or diffuser (BB5) hydraulics – high efficiency, low radial loads, long bearing life
Broad hydraulic coverage – flows 10–3,200 m³/h, heads to 4,600 m, pressures to 500 bar
Centreline mounting – maintains alignment during thermal cycling (up to 450°C)
Material flexibility – carbon steel (C‑6), 316L SS (S‑8), duplex (D‑1/D‑2), super duplex (U‑8), NACE MR0175
API 682 mechanical seal compatibility – Plan 23, Plan 52, Plan 53B, all fully supported
Low NPSH options – double‑suction first stage or inducer for problematic suction conditions
Minimum flow protection – ARC or continuous bypass integrated
Horizontal orientation – easy access for maintenance, stable operation, simple alignment
Field‑proven – thousands of BB3 and BB5 horizontal multistage pumps in refineries, power plants, pipelines, and water injection facilities worldwide
| Component | Recommended Quantity | Notes |
|---|---|---|
| Complete mechanical seal cartridge (API 682) | 1 set per pump | Specify Plan 23/53B as needed |
| Bearing set (radial + thrust) | 1 set | – |
| Wear ring set (casing + impeller) | 1 set | Includes both stationary and rotating rings |
| Balance drum (if fitted) | 1 set | – |
| Throttle bushings | 1 set | For stuffing boxes (if used) |
| Gasket / O‑ring kit (full set) | 1 set per pump | – |
| Inducer (if fitted) | 1 set | – |
For detailed selection of the correct horizontal multistage centrifugal pump (BB3 axial split or BB5 barrel) for your high‑head, high‑pressure application – including hydraulic sizing, NPSHa verification, material selection per API 610 Table H, API 682 seal plan determination, minimum flow recirculation design, and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support boiler feed, water injection, crude pipeline, refinery charge, and high‑pressure process projects worldwide with API 610 horizontal multistage centrifugal pumps – reliable, efficient, and built for 20 years of continuous service.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.