The multistage centrifugal pump is a critical machine for applications requiring high discharge pressure – far beyond what a single‑stage pump can deliver. By arranging two or more impellers in series on a single shaft, each impeller adds energy to the fluid, and the total head is approximately the sum of the individual stage heads. Multistage pumps are essential for boiler feed water, water injection, crude oil pipelines, high‑pressure reverse osmosis, refinery charge services, and hydraulic power systems.
All multistage pumps in this series are fully designed, manufactured, and certified to API 610 11th/12th edition (ISO 13709) – the global standard for centrifugal pumps in petroleum, petrochemical, and natural gas industries. API 610 classifies multistage pumps into two primary configurations:
BB3 – Axially split, single‑casing, multistage, between‑bearings (single casing)
BB5 – Radially split, double‑casing (barrel), multistage, between‑bearings (outer barrel + inner cartridge)
These pumps are built for a 20‑year design life and a minimum of 3 years of uninterrupted continuous operation.
| Pump Type | Configuration | Best Application |
|---|---|---|
| BB3 (Axial Split) | Horizontally split single casing, between bearings, opposed impellers | Boiler feed water (medium pressure), crude oil transfer, refinery process, water injection up to 150 bar |
| BB5 (Barrel) | Radially split double casing, between bearings, opposed or in‑line impellers | Ultra‑high pressure boiler feed (supercritical), water injection (>150 bar), mainline crude pipelines, hydrocracker feed |
| VS6 (Vertical) | Vertically suspended double casing, diffuser type | Low NPSH applications, offshore seawater lift, deep well pumping |
The BB3 pump offers easier maintenance because the upper casing half can be removed without disturbing piping. The BB5 barrel pump provides superior high‑pressure containment and is specified for the most severe duties.
| Parameter | BB3 (Axial Split) | BB5 (Barrel) | VS6 (Vertical) |
|---|---|---|---|
| Flow range | Up to 3,200 m³/h (14,000 gpm) | Up to 1,400 m³/h (6,160 gpm) | Up to 840 m³/h |
| Head range | Up to 2,900 m (9,500 ft) | Up to 4,600 m (15,000 ft) | Up to 900 m |
| Pressure rating | Up to 150 bar (2,175 psi) | Up to 500 bar (7,250 psi) | Up to 110 bar |
| Temperature range | –45 to +260°C | –45 to +450°C | –196 to +150°C |
| Number of stages | 3 – 14 | 2 – 16+ | 2 – 12 |
| Speed | Up to 6,000 rpm | Up to 6,500 rpm | Up to 3,600 rpm |
In a multistage centrifugal pump, the fluid enters the first stage impeller suction eye, gains velocity and pressure. It then passes through a diffuser or return channel to the next stage impeller. With each successive stage, pressure rises incrementally. The total head equals the head developed by one stage multiplied by the number of stages (less minor hydraulic losses). This allows a relatively compact pump to generate very high pressures without requiring excessive impeller diameter or rotational speed.
For example, a BB5 pump with 10 stages, each developing 150 m of head, produces 1,500 m total head – equivalent to 150 bar (2,175 psi) for water.
A major challenge in multistage pumps is axial thrust – the net hydraulic force pushing the rotor toward the suction side. API 610 multistage pumps solve this in two ways:
Opposed (back‑to‑back) impeller arrangement – identical impellers are mounted in opposing directions. They generate equal and opposite axial thrust, providing hydraulic self‑balancing. This is the preferred method for BB3 and many BB5 pumps because it eliminates complex balancing devices that can wear or foul. Opposed impellers are supplied on low‑density fluids (e.g., lean amine, light hydrocarbons) where rotor stability is critical.
Balance disc or balance drum – for in‑line impeller arrangements (all facing the same direction), a balance disc on the shaft downstream of the last stage counteracts thrust. This is common in BB5 pumps for water injection and boiler feed.
Opposed impeller designs have no contact faces, zero wear, and eliminate thrust bearing overload during start‑up and transient conditions.
In BB3 pumps, each stage incorporates a double volute casing that balances radial thrust forces, minimising shaft deflection and extending bearing life. In BB5 pumps, diffuser vanes surround each impeller, providing superior efficiency and much lower radial loads at off‑design (turndown) conditions – critical for water injection and pipeline service where flow varies.
Material selection for multistage pumps follows API 610 Table H, based on fluid corrosiveness, temperature, and pressure.
| Component | Low/Medium Duty | High Duty / Corrosive | Extreme (Seawater / Sour) |
|---|---|---|---|
| Casing (BB3) | Carbon steel (C‑6) | 316L SS (S‑8) | Duplex (D‑1/D‑2) |
| Outer barrel (BB5) | Low alloy steel (Class II) | 316L SS clad | Duplex clad or solid |
| Inner casing / diffusers | Carbon steel or 304 SS | 316L SS (S‑8) | Duplex 2205 / 2507 |
| Impellers | Carbon steel / 304 SS | 316L SS (S‑8) | Duplex / Super Duplex |
| Shaft | 4140 hardened steel | 17‑4 PH SS | Duplex / Super Duplex |
| Wear rings | 4140 or 316 SS hard faced | 316L SS + Stellite | Duplex + Stellite / tungsten carbide |
| Fasteners | 4140 (zinc plated) | 316 SS | Duplex / Inconel |
For boiler feed water, carbon steel casings are common for moderate pressure (≤100 bar). For high‑pressure, supercritical service, forged low‑alloy steel barrels are standard.
For water injection (seawater or produced water), super duplex (D‑2, UNS S32750) with PREN >40 is required to resist chloride pitting and H₂S cracking. NACE MR0175 / ISO 15156 certification is mandatory for sour service.
Multistage pumps have a seal chamber at each end of the shaft. API 682 provides the standard for sealing. Seal selection depends on pressure, temperature, and fluid hazard.
| Service | Recommended Seal | API 682 Plan | Notes |
|---|---|---|---|
| Boiler feed water (clean) | Single seal (Type B) | Plan 23 (cooled recirculation) | Maintains seal face temperature |
| Boiler feed water (high pressure) | Tandem seal (Arr. 2) | Plan 52 | Backup for safety |
| Water injection (seawater) | Dual pressurised (Arr. 3) | Plan 53B (bladder accumulator) | Zero emissions, seals faces SiC |
| Crude oil pipeline | Dual pressurised | Plan 53B | H₂S containment |
| Refinery charge (hydrocarbon) | Tandem or dual | Plan 52 / 53B | – |
Plan 23 is the standard for high‑temperature boiler feed water (up to 150°C+). It recirculates fluid from the seal chamber through a cooler and back, maintaining a stable, cool environment for the seal.
Plan 53B provides barrier fluid pressurised above process pressure, guaranteeing zero leakage of hazardous fluid.
Multistage pumps typically require very low Net Positive Suction Head at the first stage. The first stage impeller is specifically designed with a large eye and optimised inlet geometry (sometimes double suction) to minimise NPSHr. For low NPSHa applications (e.g., deaerator at 3‑5 meters head), an inducer (axial flow stage before the first radial impeller) can reduce NPSHr by 40–60%. This is common in boiler feed pumps taking suction from a low‑elevation deaerator.
Operating a multistage pump below its Minimum Continuous Stable Flow (MCSF) can cause:
Excessive radial vibration
Temperature rise (liquid heats up, may flash)
Damage to wear rings, balance device, and seals
Therefore, all multistage pumps must be equipped with a minimum flow recirculation system – either an automatically controlled recirculation valve (ARC) or a continuous bypass orifice that returns the required minimum flow to the suction tank or suction vessel.
| Industry | Application | Typical Configuration |
|---|---|---|
| Power generation | Boiler feed water (subcritical & supercritical) | BB5 barrel (high pressure) |
| Power generation | Booster feed (low‑pressure) | BB3 axial split |
| Oil & gas | Water injection (onshore / offshore) | BB5 barrel (super duplex) |
| Oil & gas | Crude oil pipeline mainline | BB5 barrel |
| Refining | Crude charge to CDU | BB3 or BB5 |
| Refining | Hydrocracker feed | BB5 barrel (special alloy) |
| Refining | Lean amine charge (high pressure) | BB3 or BB5 |
| Petrochemical | High‑pressure process feed | BB3 |
| Desalination | High‑pressure reverse osmosis feed | BB5 barrel (duplex) |
| Mining / mineral processing | High‑pressure slurry transport (limited) | BB5 with hard metal liners |
Design life: 20 years minimum
Continuous operation: Minimum 3 years uninterrupted service
Bearing life: L10 ≥25,000 hours
Critical speed: First lateral critical speed ≥120% of maximum operating speed
Centreline mounting: Standard for all multistage pumps (BB3, BB5) to accommodate thermal expansion
Hydrostatic test: Pressure casing tested at 1.5x design pressure
Performance test: Water per API 610 Grade 1 or 2, with specified tolerance
NPSH test: Full verification when specified
Material certification: EN 10204 3.1 full traceability
Hydrostatic test of outer barrel (BB5) and inner casing (BB3)
Performance test at rated speed and flow, measuring head, power, vibration, bearing temperature
Mechanical run test (minimum 4 hours) to confirm smooth operation
NPSH test (optional) using water with vacuum or gas content method
Non‑destructive examination (NDE): MPI, dye penetrant, or ultrasonic per API 610
Material certification and traceability for all pressure‑containing parts
Full API 610 compliance (BB3 / BB5 / VS6) – 11th/12th edition ISO 13709, 20‑year life
Opposed impeller (back‑to‑back) option – self‑balancing axial thrust, no balance disc wear or maintenance
Diffuser (BB5) or double volute (BB3) hydraulics – high efficiency and low radial loads
Broad hydraulic coverage – flows 10–3,200 m³/h, heads to 4,600 m, pressures to 500 bar
Material flexibility – carbon steel, 316L SS (S‑8), duplex (D‑1/D‑2), super duplex (U‑8), NACE MR0175
Centred mounting – maintains alignment for hot services (up to 450°C)
API 682 mechanical seal compatibility – Plan 23, Plan 52, Plan 53B all supported
Low NPSH options – inducer for problematic suction conditions
Balanced rotor design – minimal vibration at design and off‑design points
Field‑proven – thousands of BB3 and BB5 pumps in severe duty worldwide
| Component | Recommended Quantity |
|---|---|
| Complete mechanical seal cartridge | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Balance disc / drum (if fitted) | 1 set |
| Gasket / O‑ring kit (full) | 1 set |
| Throttle bushings | 1 set |
For detailed selection of the correct multistage centrifugal pump (BB3, BB5, or VS6) for your high‑head, high‑pressure application – including hydraulic design, NPSHa verification, material selection per API 610 Table H, seal plan (API 682), minimum flow protection, and complete API 610 data sheet – please contact our engineering team.
Email: info@hyrig.com
Our engineers support boiler feed, water injection, crude pipeline, refinery charge, and high‑pressure process projects worldwide with API 610 multistage centrifugal pumps – reliable, efficient, and built for 20 years of continuous service.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.