Jet Pump for Deep Wells – Hydraulic Artificial Lift System for High Lift, Abrasive & Sour Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Our jet pump for deep wells is a hydraulic artificial lift system that uses high‑pressure power fluid (water or oil) to lift produced fluids from depths exceeding 4,000 meters. With no downhole moving parts – no rods, no electric cable, no rotating shaft – it reliably handles sand, H₂S, paraffin and heavy crude (down to 11°API). The jet pump is deployed and retrieved by slickline, eliminating workover rig costs. Designed to API 610 material standards with 316L SS, duplex or Inconel throats for corrosive and abrasive service.

Conatct For Details
DetailReview(0)Additional

Product Overview

The jet pump for deep wells (hydraulic jet pump) is a proven artificial lift technology used in oil, gas, water and geothermal wells where conventional rod pumps, electric submersible pumps (ESPs) or progressing cavity pumps (PCPs) face reliability problems due to depth, deviation, abrasives, solids, free gas or corrosive fluids. The jet pump has no downhole moving parts – it operates on the Venturi principle: high‑pressure power fluid pumped from surface passes through a nozzle, creating a low‑pressure region that draws in reservoir fluids. The two streams mix in a throat, then slow down in a diffuser, converting velocity back into increased discharge pressure to lift the mixture to surface.

Because the jet pump contains no seals, bearings, impellers or electrical components downhole, it offers exceptional reliability in the most challenging deep well environments: sand production up to 5%, H₂S content, CO₂, paraffin, scale, high temperature (up to 350°F/177°C) and deviated or horizontal wellbores. The pump is typically deployed and retrieved by slickline, avoiding expensive workover rigs, and can be installed in wells too deep or too crooked for rod pumps.

While API 610 (ISO 13709) applies to surface centrifugal pumps, the materials, design pressures and quality standards for a deep well jet pump are fully specified to match API 610 requirements. All wetted components – nozzle, throat, diffuser, body – can be manufactured from API 610 Table H materials (S‑8 316L, D‑1 2205 duplex, D‑2 2507 super duplex, C‑6 carbon steel) with NACE MR0175 certification for sour (H₂S) service. The surface power fluid pump (which supplies the high‑pressure motive fluid) is typically an API 610 BB5 barrel or BB3 multistage centrifugal pump, making the entire system API 610 compliant from power end to downhole assembly.

How the Deep Well Jet Pump Works

The system consists of three main components:

  1. Surface power fluid pump – an API 610 high‑pressure centrifugal pump (BB5 or BB3) that pressurises clean power fluid (treated produced water, crude oil or water).

  2. Downhole jet pump assembly – a cylinder housing that contains the nozzle, throat and diffuser. It is run on slickline or on tubing and seated in a seating nipple.

  3. Power fluid string – tubing or coiled tubing that carries high‑pressure power fluid down to the jet pump.

Operational cycle:

  • Power fluid (at 1,500–5,000 psi / 100–350 bar) flows down the tubing and exits through a converging nozzle, converting pressure into velocity (up to 60–120 m/s).

  • The high‑velocity jet creates a low‑pressure zone in the suction chamber, drawing reservoir fluids through inlet ports.

  • The two fluids mix in the throat (mixing tube) , then pass through a diverging diffuser where velocity is converted back to pressure.

  • The combined fluid (power fluid + produced fluid) returns to surface through the annulus between tubing and casing.

Because the pump has no close clearances between moving parts (there are no moving parts), sand, fines and corrosion by‑products pass through without causing wear or jamming.

Key Technical Specifications (Deep Well Service)

ParameterRange / Capability
Well depthUp to 5,000 m (16,400 ft) – tested to 12,000 ft+
Flow rate (liquid)50 – 30,000 bpd (8 – 4,800 m³/d)
Discharge pressureUp to 350 bar (5,000 psi)
Lift (total dynamic head)Equivalent to 1,500 m+ of vertical lift
Power fluid pressure70 – 350 bar (1,000 – 5,000 psi)
Power fluid rate0.5 – 10 times produced fluid rate (depending on pump ratio)
Sand toleranceUp to 5% by volume
Free gas handlingUp to 50% gas volume fraction (GVF) with modified design
Operating temperatureUp to 177°C (350°F) , higher with specialty alloys
Fluid viscosityUp to 5,000 cP (heavy oil down to 11°API)
Well deviationAny angle – horizontal, deviated, or vertical
Retrieval methodSlickline, wireline, or coiled tubing (no rig required)

Materials – API 610 Grade Downhole

ComponentStandard MaterialUpgrade API 610 ClassRemarks
Nozzle (orifice)316L stainless steelS‑8Precision electro‑discharge machined (EDM)
Throat (mixing tube)316L SS or tungsten carbideS‑8 / hard metal insertTungsten carbide for extreme sand
Diffuser316L SSS‑8–
Housing / body4140 steel (NACE) or 316L SSC‑6 (NACE) / S‑8NACE MR0175 for H₂S
Fluid end (pump body)Duplex 2205 or 2507D‑1 / D‑2For high chlorides, seawater, sour gas
Seals / O‑ringsFKM (Viton) or AFLAS–Viton up to 200°C, AFLAS for high temp & sour

For deep wells with H₂S partial pressure above NACE limits, NACE MR0175 / ISO 15156 certification is mandatory for all downhole components. For extreme abrasion (frac sand, proppant flowback), the throat can be lined with tungsten carbide or ceramic – these materials are not covered by API 610 but are compatible with the pump design.

Surface Power Fluid Pump – API 610 Integration

The jet pump requires a reliable, high‑pressure source of power fluid. This is almost always an API 610 centrifugal pump:

  • For moderate flow, high pressure (most common) : BB5 double‑case barrel pump (e.g., Sulzer GSG, Flowserve WXB). Pressure up to 350 bar, flow up to 1,400 m³/h.

  • For lower flow, deep well unloading : BB3 axially split multistage pump (pressure up to 150 bar).

  • For offshore or platform applications : OH2 single‑stage or high‑speed BB5 units.

The surface pump and the downhole jet pump are sized together using the jet pump performance curves (head ratio vs. flow ratio). The complete package (surface pump, power fluid conditioning, downhole jet pump) can be supplied as an integrated artificial lift system.

Advantages of Jet Pump for Deep Wells over Other Artificial Lift Methods

FeatureJet PumpRod Pump (SRP)ESPPCP
Moving parts downholeNoneMany (pump, rods, rod guides)One (motor + pump)One (rotor in stator)
Sand handlingExcellent (5%+ sand)Poor (sand sticks pump)Poor (abrades bearings)Poor (stator damage)
Gas handlingGood (50% GVF)Poor (gas lock)Poor (gas lock, overheating)Moderate
Deviated / horizontal wellsExcellentPoor (rod wear)GoodModerate
H₂S / corrosive fluidsExcellent (NACE alloys)Poor (rod & tubing corrosion)Fair (motor cable issues)Fair
Workover cost for pump changeSlickline (low cost)Rig (high cost)Rig (high cost)Rig or coiled tubing
Depth capability>5,000 m<3,000 m (limited by rod weight)>4,000 m (but motor size limited)<2,500 m (elastomer limits)
Heavy oil (>500 cP)Good (can be heated by power fluid)PoorPoorGood (but elastomer limit)
Initial capital costMedium‑highLowMediumMedium
Operating cost (energy)Lower than ESP at high liftLow for shallowHigher for deepMedium

Applications for Deep Well Jet Pump

ApplicationTypical DepthFluidsWhy Jet Pump Preferred
Oil well artificial lift1,500–4,500 mHeavy crude, sand, H₂SNo moving parts, slickline retrievable, handles sand
Gas well deliquification (dewatering)1,000–4,000 mWater, condensate, gasLifts liquids without gas locking; can operate with high GVF
Coal bed methane (CBM) water removal300–1,500 mWater with finesHandles coal fines, no rod pump wear
Geothermal well pumping1,000–3,000 mBrine, high temperature (200°C+)No downhole electrical components, high temperature alloys
Produced water injection well boosting1,500–3,000 mTreated waterHigh pressure lift with abrasives
Well unloading after workoverAny depthKill fluid, oil, waterTemporary installation, no permanent equipment needed
Offshore platform deep wells2,000–4,000 mCrude, water, sandsSmall footprint; no ESP cable penetrators

Design & Sizing – Deep Well Jet Pump

Proper sizing requires the following well data:

  • Depth (measured depth and true vertical depth)

  • Tubing size and casing size (ID)

  • Reservoir pressure and productivity index (PI)

  • Produced fluid properties (density, viscosity, GOR, water cut)

  • Sand production percentage

  • H₂S and CO₂ concentrations

  • Available power fluid pressure and rate (from surface API 610 pump)

The jet pump package is defined by three key ratios:

  1. Nozzle area – controls power fluid rate and velocity.

  2. Throat area – controls mixing and lift efficiency.

  3. Nozzle/throat area ratio (R) – typically 0.2 to 0.5 for oil wells, producing a pump ratio (power fluid volume per produced volume) of 0.5:1 to 3:1.

The pump performance is displayed as a Head Ratio (H) vs. Flow Ratio (M) curve. The intersection of the well’s inflow performance relationship (IPR) and the pump’s characteristic curve determines the operating point.

Engineering computer programs (e.g., JEM, Beall Jet Pump Software) are used to match the nozzle and throat sizes to the well conditions. Field adjustment is possible by retrieving the pump with slickline and swapping the nozzle/throat cartridge – no rig required.

NPSH and Cavitation in Downhole Jet Pumps

Unlike surface pumps, downhole jet pumps operate with the suction port exposed to reservoir pressure. Cavitation occurs when the absolute pressure in the mixing throat falls below the vapour pressure of the produced fluid. This is a function of:

  • Power fluid pressure and nozzle velocity

  • Throat geometry (matching nozzle/throat area ratio)

  • Produced fluid properties (vapour pressure, gas content)

Cavitation can be minimised by selecting a lower nozzle/throat ratio (increasing throat area) or by increasing power fluid pressure. The pump supplier provides cavitation limit curves that define the maximum flow ratio for a given throat design.

Reliability and Maintenance – Deep Well

Downhole maintenance:

  • The jet pump is retrieved by slickline – a standard wireline unit (not a workover rig) can pull and rerun the pump in a few hours.

  • Typical service interval: 6–24 months, depending on sand and corrosion.

  • Routine maintenance consists of replacing the nozzle and throat cartridge (pre‑machined, low‑cost components). The housing stays downhole.

Surface maintenance:

  • The API 610 power fluid pump requires standard API maintenance (seals, bearings, wear rings every 12,000–20,000 hours).

  • Power fluid filtration is critical – typically a 5–10 micron filter to prevent nozzle plugging.

API 610 Alignment Summary

Although the downhole jet pump is not itself an API 610 centrifugal pump, the entire artificial lift system follows API 610 engineering logic:

  • The surface power fluid pump is fully API 610 certified (OH2, BB3, or BB5).

  • The downhole jet pump nozzle and throat are manufactured to API 610 Table H material classes (S‑8, D‑1, D‑2) with NACE MR0175.

  • Design pressures and hydrostatic testing of the pump housing follow ASME B16.34, same as API 610 casing classes.

  • The system is designed for 20‑year asset life with minimum 3‑year continuous operation of the surface pump.

Why Choose Our Jet Pump for Deep Wells?

  • No downhole moving parts – eliminates rod, seal, bearing, and ESP cable failures.

  • Slickline retrievable – pump change in hours without a workover rig, saving millions in lost production and rig costs.

  • Handles sand, H₂S, CO₂, paraffin, scale – materials selected per API 610 / NACE MR0175 with tungsten carbide throat option for extreme abrasion.

  • Works in deviated, horizontal, and deep wells – no depth or angle limitations.

  • API 610 grade surface power pump – integrated, reliable, proven in oilfield service.

  • High temperature capability – up to 350°F (177°C) with standard alloys, higher with Inconel/Monel.

  • Flexible power fluid – use produced water, crude oil, or clean water as the power medium.

  • Low operating cost (energy) – for deep high‑volume wells, jet pump energy efficiency often exceeds ESP due to lack of downhole electrical losses.

  • Proven field history – thousands of deep well jet pumps in heavy oil, sour gas, dewatering and offshore service.

Get a Quote or Engineering Support

For a complete deep well artificial lift solution – including well performance analysis, nozzle/throat sizing, API 610 surface pump selection, NACE material compliance, and slickline deployment procedures – please contact our engineering team.

Email: info@hyrig.com

Our engineers support onshore and offshore deep well pumping projects worldwide – from heavy oil and gas deliquification to high‑pressure water injection and geothermal lift – with API 610 grade hydraulic jet pump systems.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit