Pressure Seal vs Bolted Bonnet Gate Valve | Class Boundary

2026-11-16 19:08

Pressure Seal vs Bolted Bonnet Gate Valve

HYRIG supplies gate valves with both bolted and pressure-seal bonnets. This guide explains the mechanical difference, the pressure class boundary where pressure-seal becomes standard, and the maintenance implications for each design.

Key Facts

  • Bolted bonnet: Used for Class 150 through 900. Easy to disassemble. Bolt load must be maintained to prevent leaks.
  • Pressure-seal bonnet: Standard for Class 1500 and 2500. Line pressure assists the seal. No massive bolting required.
  • Boundary: ASME B16.34 allows bolted bonnets above Class 900, but industry practice shifts to pressure-seal for high pressure and large sizes.
  • Maintenance: Bolted bonnets are easier to access. Pressure-seal bonnets require specific procedures to release the gasket.

Key Specifications

FeatureBolted BonnetPressure-Seal Bonnet
Typical Pressure ClassClass 150 - 900Class 1500 - 2500
Sealing MechanismBolt load compresses gasketLine pressure pushes seal ring against body
Bolting SizeProportional to pressure classSmaller, independent of pressure
DisassemblyUnbolt and liftRemove seal ring, requires specific procedure
WeightIncreases with classLighter than equivalent bolted design

Dimensions

DimensionStandard
Face-to-faceASME B16.10
Flanged endsASME B16.5 / B16.47
Butt weld endsASME B16.25

Structure and Working Principle

A bolted bonnet uses studs and nuts to compress a gasket between the body and bonnet. As pressure class increases, the flange thickness and bolt size must increase to maintain sufficient gasket seating stress. Above Class 900, the bolts become very large and heavy, making assembly and disassembly difficult.

A pressure-seal bonnet uses a self-energizing seal. The bonnet is held in place by a retaining ring, and a soft metal gasket sits between the bonnet and the body. As internal pressure rises, it pushes the gasket outward and upward, increasing the sealing force. This means the seal gets tighter as pressure increases, and the bolting does not need to carry the full pressure load.

Cross-Reference and Replacement

When replacing or maintaining gate valves:

  1. Check the bonnet type: For Class 150-900, bolted bonnets are standard and easy to service. For Class 1500-2500, confirm the pressure-seal procedure before disassembly.
  2. Verify the gasket type: Bolted bonnets use spiral wound or ring joint gaskets; pressure-seal bonnets use specific pressure-seal rings.
  3. Review maintenance procedures: Pressure-seal bonnets require a specific sequence to release the retaining ring safely.

Applications

  • Bolted bonnet: General process piping, Class 150-900 steam and hydrocarbon lines, applications requiring frequent maintenance.
  • Pressure-seal bonnet: High-pressure steam, Class 1500-2500 boiler feedwater, high-pressure gas transmission where weight and sealing reliability are critical.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.

Frequently Asked Questions

Q: At what pressure class should I use a pressure-seal bonnet?

Industry standard practice is to use pressure-seal bonnets for Class 1500 and 2500. Bolted bonnets are standard for Class 150-900.

Q: Can a pressure-seal bonnet be repaired in the field?

Yes, but it requires specific procedures and tools to release the retaining ring and replace the pressure-seal gasket. Follow the manufacturer's instructions.

Q: Is a pressure-seal bonnet lighter than a bolted bonnet?

Yes. Because the bolting does not need to carry the full pressure load, the flange and bolts can be smaller, reducing the overall valve weight at high pressure classes.

Q: What is the typical lead time?

Standard lead time is 4 to 6 weeks depending on size, class, and material.

Selection Support

To select the correct bonnet design, provide the line pressure class and maintenance requirements. Our engineers will confirm the configuration.

Contact

For help selecting between pressure-seal and bolted bonnet gate valves, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment