HYRIG can supply the API 600 gate valve range. The API 600 gate valve is a rising-stem isolation valve designed for on/off service in high-temperature and high-pressure pipelines. Gate valves with NPS 2 and larger use flexible wedge discs; gate valves below NPS 2 use solid wedge discs.
| NPS | DN | L RF (mm) | L RTJ (mm) | L BW (mm) | d (mm) | H (mm) | W (mm) | Weight (kg) |
|---|---|---|---|---|---|---|---|---|
| 1/2 | 15 | 108 | 119 | 108 | 14 | 218 | 120 | 4 |
| 1 | 25 | 127 | 140 | 127 | 25 | 256 | 140 | 7 |
| 2 | 50 | 178 | 191 | 216 | 30 | 340 | 200 | 20 |
| 3 | 80 | 203 | 216 | 283 | 76 | 410 | 250 | 36 |
| 4 | 100 | 229 | 241 | 305 | 100 | 485 | 280 | 54 |
| 6 | 150 | 267 | 279 | 403 | 150 | 595 | 310 | 82 |
| 8 | 200 | 292 | 305 | 419 | 200 | 755 | 360 | 136 |
| 12 | 300 | 356 | 368 | 502 | 300 | 1040 | 460 | 299 |
| Dimension | Standard |
|---|---|
| Face-to-face (RF) | ASME B16.10 |
| Face-to-face (RTJ) | ASME B16.10 |
| Face-to-face (BW) | ASME B16.10 |
| Flanged ends | ASME B16.5 / B16.47 |
| Butt weld ends | ASME B16.25 |
| Pressure-temperature rating | ASME B16.34 |
| Wall thickness | API 600 |
The gate valve uses a wedge-shaped disc that seats against two inclined seat rings. When the handwheel is turned, the stem rises and lifts the disc out of the flow path, creating a straight-through bore with very low pressure drop.
Two structural details determine the valve's behavior:
The backseat design allows the stem packing to be replaced while the valve is under pressure, provided the valve is fully open.
Replacing an API gate valve requires verification of four factors:
Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. For high-temperature service, verify material compatibility and thermal expansion limits with the manufacturer.
Q: What is the difference between flexible and solid wedge gate valves?
A flexible wedge has a cut around its perimeter to allow slight deformation under thermal cycling, preventing sticking. A solid wedge is rigid and suited to smaller sizes and lower temperatures.
Q: When should I use a pressure seal bonnet?
Pressure seal bonnets are standard for Class 1500 and 2500 gate valves. For Class 150-900, bolted bonnets are sufficient and easier to maintain.
Q: What is the difference between a gate valve and a ball valve?
A gate valve uses a wedge disc that lifts out of the flow path, providing straight-through flow with low pressure drop. A ball valve uses a rotating ball with a through-hole. Gate valves are preferred for on/off service in high-temperature lines; ball valves offer faster operation and tighter shutoff.
Q: Can the stem packing be replaced under pressure?
Yes, when the valve is fully open, the backseat engages the bonnet, isolating the packing area. The packing can be replaced while the line remains pressurized, provided the backseat is in good condition.
Q: What is the typical lead time?
Standard lead time is 4 to 6 weeks depending on size, class, material, and actuation requirements.
To confirm the correct gate valve configuration for your line, provide the line size, pressure class, operating temperature, and end connection type. Our engineering team will verify the disc type and bonnet design.
For API 600 gate valve selection, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.