The SCSZ and DCSZ series are high‑pressure multistage centrifugal pumps designed and manufactured to API 610 10th Edition (ISO 13709) standards. They incorporate self‑balancing hydraulic technology to eliminate the traditional balancing disc/drum, significantly improving operational reliability and reducing maintenance requirements.
The SCSZ series is of Type BB4 construction – a single casing, radially split diffuser‑type, ring‑section (segmental) multistage pump with tie‑bolt assembly. It is well suited for medium‑to‑high pressure service (up to 30 MPa), where the robust segmented casing provides reliable pressure containment. The DCSZ series is of Type BB5 double casing (barrel) construction. The outer barrel (forged steel) serves as the primary pressure vessel, while the inner radially split core houses the opposed impeller stack. This BB5 design provides a second pressure containment barrier and is required for extra high pressure applications (up to 35 MPa) involving hazardous or toxic fluids like liquid ammonia (NH₃ is toxic, requiring zero‑atmospheric‑leakage containment). The DCSZ is the preferred configuration for ammonia synthesis loops at 15‑35 MPa / 150‑350 bar, while the SCSZ can also serve such duties at lower pressures.
Why Self-balancing for High Pressure Ammonia?
Conventional multistage pumps rely on a balancing disc/drum to counteract hydraulic axial thrust. These devices operate with very small clearances and degrade rapidly when handling non‑lubricating fluids like liquid ammonia, leading to increased vibration, seal failure, and unplanned shutdowns. The SCSZ/DCSZ self‑balancing design arranges two opposing groups of impellers (back‑to‑back), so the axial hydraulic forces generated by each group cancel each other – eliminating the fragile balance disc/drum entirely. This provides:
No balance disc wear – eliminates the most common multistage pump failure
Higher efficiency (no disc friction / balancing water recirculation loss)
No axial thrust pulses during start‑up or shut‑down
Extended mechanical seal life (up to 3× conventional design)
Unaffected by low‑viscosity, non‑lubricating fluids (ideal for liquid ammonia)
Series Comparison (BB4 vs BB5)
| Feature | SCSZ Series (BB4) | DCSZ Series (BB5) |
|---|---|---|
| API 610 Type | BB4 – single casing, radial split, diffuser‑type, ring‑section | BB5 – double casing (barrel), outer forged barrel + inner core |
| Casing construction | Single radially split casing, tie‑bolt assembly | Double casing – radial split inner + outer barrel pressure shell |
| Pressure rating | Up to 30 MPa / 300 bar | Up to 35 MPa / 350 bar |
| Temperature range | -80°C to +210°C | -80°C to +450°C |
| Flow range | 5 – 730 m³/h | Up to 1200 m³/h |
| Head capability | Up to 2800 m (8 – 12 stages) | Up to 3400 m (12 – 16 stages) |
| Best suited service | Medium‑high pressure ammonia feed (<300 bar) | Extra‑high pressure ammonia feed / carbamate (>300 bar) |
| Primary pressure containment | Single casing | Outer barrel + inner casing back‑up |
| Outage maintenance | Complete pump removal required | Cartridge pull‑out – full rotor removal without disturbing outer barrel or piping |
Design Features (Common to SCSZ & DCSZ)
| Feature | Description |
|---|---|
| Opposed impeller arrangement (back-to-back) | Impellers arranged in two opposing groups, generates inherent axial thrust self-balancing; no balance disc/drum – eliminates the most common multistage pump failure; specially suited for low‑density fluids like liquid ammonia; DCSZ double casing (BB5) feature – inner core extracted without disturbing outer barrel |
| Double suction first stage impeller (optional) | Significantly reduces Net Positive Suction Head Required (NPSHr); prevents cavitation when pumping ammonia from storage with limited submergence |
| Diffuser type casing (radial split) | Stationary diffusers between stages provide smooth hydraulics, high efficiency, and reduced radial loads; SCSZ single casing (BB4) – ring‑section joined by tie‑bolts; DCSZ double casing (BB5) – inner diffuser core sits inside outer forged barrel |
| Centerline support | Casing supported at horizontal centerline; uniform thermal expansion at elevated temperatures; prevents shaft misalignment |
| Renewable wear parts | Casing rings, impeller rings, and interstage bushings field replaceable; restores efficiency – no need for major casting changes |
| API 682 seal chamber | Fully compliant with API 682 4th Edition; accommodates single, tandem (Plan 52), and double (Plan 53B) cartridge mechanical seals; DCSZ barrel provides secondary zero‑leakage containment (Plan 53B mandatory for ammonia) |
| Heavy-duty bearings | Angular contact thrust bearings + cylindrical roller radial bearings; oil ring self‑lubricating (standard) or forced oil circulation (high power); water‑cooled bearing housings included for fluid >120°C |
| Cartridge pull-out design (DCSZ BB5) | Complete rotating assembly (impellers, diffusers, shaft, bearings, seal cartridge) removable axially from outer barrel without disturbing piping – simplifies maintenance in continuous chemical plant operation |
| Forged outer barrel construction (DCSZ BB5) | Robust forged steel cylinder; fully radiographed and hydro-tested to 1.5× design pressure; multiple closure options available |
DCSZ features include:
Flange orientation: side‑in / side‑out or side‑in / top‑out options for piping flexibility
High‑standardization design reduces spare parts inventory (interchangeability across sizes)
Extensive monitoring provisions include bearing RTD, vibration probes, discharge pressure, and temperature transmitters – fully compatible with DCS integration
Materials for High Pressure Ammonia – Copper‑free Alloys
Liquid ammonia (anhydrous) does not corrode carbon steel or stainless steel when dry, but trace moisture promotes corrosion, and copper and its alloys are rapidly attacked by ammonia. All wetted components shall be copper‑free. Material selection shall consider the worst‑case combination of temperature, pressure, purity, and possibility of moisture ingress.
| Component | Standard (Liquid Ammonia) | Upgrade (High Purity / Severe Conditions) |
|---|---|---|
| Outer barrel (DCSZ) | Forged carbon steel (A216 WCB) | Forged 316L stainless steel |
| Inner casing / diffusers | 316L stainless steel | Duplex 2205 / super duplex 2507 (25% Cr) |
| Impellers | 316L stainless steel (back‑to‑back) | Duplex / super duplex (25% Cr min) |
| Shaft | 17-4PH stainless steel | Duplex / super duplex / Inconel 718 |
| Wear rings / interstage bushings | 316L with Stellite hard facing | Silicon carbide / tungsten carbide |
| Casing bolting (tie‑rods, flanges) | A193 B7 (carbon steel) | A193 B8M (316 SS) / duplex |
| Gaskets / O‑rings | PTFE or EPDM | FFKM (Kalrez) |
SCSZ vs DCSZ material selection guidance: For ammonia / urea service, all wetted parts must be copper‑free. DCSZ outer barrel – forged carbon steel WCB (cost‑effective) or forged 316L SS (higher corrosion allowance). Inner casing, diffusers, impellers – 316L SS or duplex / super duplex depending on temperature and corrosivity. Shaft – 17-4PH SS stands up in most ammonia duties. Wear rings, interstage bushings – hard carbide recommended for long service life. Gaskets – PTFE, FFKM (upgrade for broadest chemical resistance).
Seal & Flush Plan Selection – API 682 Plan 53B
Liquid ammonia is toxic. Zero leakage to atmosphere is mandatory.
| Service | Recommended Seal Configuration | Flush Plan |
|---|---|---|
| High pressure liquid ammonia feed (>250 bar) | Double mechanical seal (pressurized) | Plan 53B – Pressurized barrier fluid reservoir with bladder accumulator (barrier fluid pressurized 1‑3 bar above pump suction pressure) |
| Ammonia synthesis feed (15‑35 MPa / 150‑350 bar) | Double mechanical seal (pressurized) | Plan 53B (zero ammonia leakage) |
| Ammonia with low hazard / low pressure | Single mechanical seal | Plan 11 (internal recirculation) – not recommended for high‑pressure, toxic service |
| Dual barrier / severe service | Double mechanical seal (pressurized) | Plan 54 – external barrier fluid circulation system (with pumps, filters, coolers) |
Seal face selection: Inner seal – tungsten carbide vs. carbon (for non‑lubricating, low viscosity ammonia). Outer seal – silicon carbide vs. carbon. Secondary seals: FFKM (Kalrez) or PTFE – EPDM and Buna‑N NOT suitable for anhydrous ammonia.
Plan 53B system requirements: Pressurized barrier fluid reservoir with bladder accumulator; pressure transmitter; level transmitter (low level alarm indicates inner seal leakage); temperature transmitter; nitrogen supply connection.
Auxiliary Systems & Monitoring
| System | Requirement |
|---|---|
| Minimum flow protection | Automatic recirculation valve (ARC) – prevents overheating and cavitation during low load or start‑up; Must be sized for continuous recirculation or equipped with temperature control |
| Bearing cooling | Water‑cooled bearing housings recommended for fluid >120°C and for all continuous high‑pressure ammonia service – extends bearing life |
| Casing drains | Low‑point drains with double isolation valves – for safe purging and maintenance (ammonia is toxic and corrosive) |
| Casing vents | High‑point vents – for startup air removal (vent to flare or safely treated) |
| Baseplate | Heavy duty fabricated steel baseplate – epoxy grouted, designed to 2× API 610 nozzle loads |
| Coupling | Flexible spacer type – allows seal/bearing replacement without moving driver |
Monitoring Systems (per API 670)
| Parameter | Monitoring Method |
|---|---|
| Bearing temperature | RTD probes (PT100) in both drive‑end and non‑drive‑end housings – 4‑20 mA to DCS, alarm at 85°C, trip at 95°C |
| Vibration | Proximity probes (eddy current) for shaft displacement – mandatory for BB5; accelerometers for bearing housing velocity (optional) |
| Suction pressure | Pressure transmitter with low suction interlock – protect against NPSH violation (cavitation) |
| Discharge pressure | Pressure transmitter with high limit alarm to DCS – over‑pressure protection |
| Process temperature | Thermowell‑mounted temperature transmitter on suction and discharge nozzles – real‑time monitoring |
| Seal support system (Plan 53B) | Reservoir level, pressure, temperature – continuous monitoring for leakage detection |
Advantages of SCSZ/DCSZ for High Pressure Ammonia Feed
Full API 610 10th Edition (ISO 13709) compliance – heavy‑duty process pump design; certified for demanding chemical service
BB4 (SCSZ) and BB5 (DCSZ) design options – covering medium to extra‑high ammonia pressure requirements (300‑350 bar)
Self‑balancing symmetrical opposed impeller arrangement – eliminates balance disc/drum failures; specially suited for low‑density, non‑lubricating, high‑pressure liquid ammonia
Double casing (BB5) DCSZ design – second pressure containment barrier for toxic ammonia service
Zero ammonia emission to atmosphere – API 682 Plan 53B double mechanical seals with pressurized barrier fluid; full API 682 4th Edition compatibility
Low NPSH capability – optional double suction first stage; reduces NPSHr by up to 70% compared to standard single‑suction configuration
Continuous heavy‑duty operation – 25‑year design life; 3‑5 years mean time between overhauls
Copper‑free materials – 316L, duplex, super duplex available; fasteners, gaskets selected for ammonia compatibility
Cost‑effective alternative to imported BB5 pumps – drastically lower price; comparable API 610 quality and performance; proven in fertilizer and green ammonia applications
Applications
| Industry | Service |
|---|---|
| Fertilizer plants (urea / green ammonia) | High pressure ammonia feed pump – 15‑35 MPa liquid ammonia to synthesis loop |
| Urea production | High pressure carbamate recirculation (with 25% Cr super duplex materials) |
| Green ammonia – renewable‑driven synthesis | Ammonia charge pump / NH₃ feed for high pressure loop (15‑20 MPa common) |
| Oil & gas – water injection | High pressure injection pump for reservoir pressure maintenance |
| Power generation (nuclear / thermal) | Boiler feed water (BSFW) – carbon steel / alloy construction |
| Coal chemical | High pressure ash water transport |
| Steel industry | High pressure descaling applications |
| Refineries | High pressure hydrocarbon transport / crude oil shipment lines |
| General industrial & mining | High pressure high lift mine drainage / long‑distance water pipeline pumping |
For more information or a custom proposal for your high pressure ammonia feed pump (SCSZ BB4 / DCSZ BB5 self‑balancing multistage pump) application, contact us at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.