Submersible Borehole Pump – Multi‑Stage Deep Well Pump for Water Supply, Irrigation & Mining

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Multi‑stage submersible borehole pump for clean water extraction from deep wells, boreholes, and reservoirs. Designed for 4″, 6″, 8″, 10″ and 12″ diameter wells. Stainless steel AISI 304 or 316 wetted parts. Corrosion‑resistant, abrasion‑tolerant, suitable for sand content up to 0.25%. NEMA standard motors. Flows to 520 m³/h, heads to 780 m, immersion to 350 m. Applications: municipal water supply, agricultural irrigation, mining dewatering, groundwater lowering, pressure boosting.

Conatct For Details
DetailReview(0)Additional

Product Overview

A submersible borehole pump is a multi‑stage vertical centrifugal pump designed to operate fully submerged in a borehole, well, or reservoir. The pump and motor are integrally coupled into a single compact unit – the motor sits below the pump, and the entire assembly is lowered into the borehole suspended from the discharge pipe. The surrounding water cools the motor, and the multi‑stage design generates high discharge pressure to lift water from significant depths to the surface.

Submersible borehole pumps are indispensable for:

  • Municipal water supply systems drawing from groundwater sources

  • Agricultural irrigation (center pivots, sprinkler systems, drip irrigation)

  • Mining dewatering and groundwater management

  • Industrial process water and pressure boosting

  • Groundwater lowering for construction and civil engineering

  • Domestic water supply for rural and peri‑urban housing

Within API 610 (ISO 13709) classification, large heavy‑duty submersible borehole pumps are categorised under the VS (Vertically Suspended) group. They correspond to the VS4 structural type — vertical suspended, single or multi‑stage, long‑shaft design with intermediate bearings, capable of deep immersion and operating under the pumped liquid level. For the most demanding high‑pressure clean water applications (municipal supply, large‑scale irrigation, high‑pressure boosting), the VS4 configuration is the standard. For extremely aggressive or corrosive fluids, a VS6 double‑casing design can be specified, which fully encloses the internal pump stages within an outer can.

Pump Configurations & Borehole Diameters

Submersible borehole pumps are sized to fit standard borehole diameters. The pump outer diameter determines the minimum well size required, expressed in inches (e.g., 4″, 6″, 8″, 10″, 12″) or in millimeters (e.g., 100 mm, 150 mm). All pumps can be coupled to NEMA standard submersible motors.

Borehole DiameterTypical Pump SeriesStandard MaterialFlow Range (max)Head Range (max)Applications
4″ (100 mm)4ST, SP, 4” seriesAISI 304 stainless steelUp to 24 m³/hUp to 330 mDomestic water, small irrigation, rural supply
6″ (150 mm)6SP, CORAChrom, Lowara Z6AISI 304 / DuplexUp to 60 m³/hUp to 400 mFarm irrigation, industrial supply, mining
8″ (200 mm)Lowara Z8/ZR8, Grundfos SPAISI 304 / DuplexUp to 180 m³/hUp to 550 mMunicipal water, multiple homes, large irrigation
10″–12″ (250–300 mm)GZ10/GZ12, GouldsAISI 304 / Duplex / 316Up to 520 m³/hUp to 545 mLarge‑scale municipal, flood irrigation, fire fighting

The table above provides general guidance; exact performance varies by model and number of stages.

Key Technical Specifications

Parameter4″ Models6″ Models8″ Models10″–12″ Models
Flow rangeUp to 24 m³/hUp to 100 m³/hUp to 180 m³/hUp to 520 m³/h
Head rangeUp to 330 mUp to 400 mUp to 550 mUp to 545 m
Motor power0.37 – 7.5 kW5.5 – 37 kW5.5 – 150 kW4 – 350 kW
Maximum immersion100 m150 m350 m350 m
Maximum operating pressure25 bar40 bar55 bar55 bar
Liquid temperature0 – 35°C0 – 40°C0 – 40°C0 – 60°C
Sand tolerance≤0.25% by weight≤0.25% by weight≤0.25% by weight≤0.25% by weight
Speed2,850 – 2,900 rpm (50Hz)2,850 – 2,900 rpm2,850 – 2,900 rpm2,850 – 2,900 rpm

Materials – Corrosion & Abrasion Resistance

Submersible borehole pumps must withstand corrosive groundwater (high iron content, salinity, chlorides, low pH) and abrasive sand. AISI 304 stainless steel is standard, AISI 316 is recommended for more aggressive environments, and Duplex stainless steel is specified for the most demanding conditions (seawater intrusion or extremely aggressive groundwater chemistry).

ComponentStandard (AISI 304)Premium (AISI 316)Heavy Duty (Duplex)Extreme Duty
Pump casing / outer shellAISI 304AISI 316Duplex (UNS S31803 / S32205)Super Duplex (UNS S32750)
Impellers (floating)Thermoplastic / NorylStainless steel AISI 304Stainless steel AISI 316Duplex / Super Duplex
Diffusers / stagesThermoplastic or stainless steelStainless steelStainless steelDuplex
ShaftStainless steel AISI 420 / 431Stainless steel AISI 316DuplexSuper Duplex
Motor housingStainless steel AISI 304Stainless steel AISI 316Stainless steel AISI 316 / DuplexSuper Duplex
Wear rings / bearingsThermoplastic or bronzeStainless steel hard‑facedStainless steel + StelliteHard metal / ceramic
FastenersStainless steelStainless steelDuplexDuplex

Floating impeller design is a critical feature: each impeller “floats” independently of adjacent stages. When the pump starts, the impellers automatically lift and seal against fixed diffusers, providing dynamic self‑adjustment that compensates for wear due to abrasion and sand. This design ensures easy starting, long life, and automatically aligns under varying pumping conditions.

Hydraulic Design – Multi‑Stage for High Head

The submersible borehole pump is a multi‑stage vertical centrifugal pump with each stage comprising an impeller and a diffuser. Fluid enters the first stage impeller, gains velocity, passes through the diffuser (which converts velocity to pressure), then flows to the next stage. The total head is the sum of each stage head. With as many as 26 stages, the pump can deliver heads exceeding 780 meters (2,560 feet).

Key hydraulic features:

  • Multi‑stage diffuser design – Each diffuser converts kinetic energy into pressure efficiently; optimized hydraulics achieve 75‑85% efficiency at best efficiency point (BEP).

  • Dynamic wear rings (on premium models) – Reduce hydraulic recirculation losses and prevent blocking during standby periods.

  • Independently floating impellers – Automatically adjust to match pumping conditions, ensuring optimal performance across varying flow demands.

  • Sand‑tolerant design – Handles sand content up to 0.25% without rapid wear.

Motor – Submersible, IP68, NEMA Standard

The pump is close‑coupled to a submersible electric motor. The motor is installed below the pump, immersed in the pumped liquid, which provides continuous cooling.

Motor specifications:

Parameter4″ motors6″ motors8″ motors10″+ motors
Power range0.37 – 7.5 kW5.5 – 45 kW5.5 – 200 kW4 – 350 kW
Voltage230V (single‑phase) / 400V (three‑phase)400V / 415V three‑phase400V / 690V three‑phase400V / 3.3kV / 6.6kV
Frequency50Hz (or 60Hz)50Hz / 60Hz50Hz / 60Hz50Hz / 60Hz
Protection classIP68 (permanent submersion)IP68IP68 (IP58 optional)IP68
Insulation classF (155°C)FFF / H
Flange standardNEMANEMANEMANEMA
Motor type (small)Oil‑filled, water‑lubricated bearingsCanned type / resin‑filled statorSand‑shielded, liquid‑lubricated bearingsCustom

The MS6000 series motors (Franklin Electric) are widely used in 6″ and 8″ borehole pumps, featuring:

  • Built‑in sand shield to protect bearings from abrasive particles

  • Liquid‑lubricated bearings (water‑lubricated, self‑replenishing)

  • Pressure‑equalising diaphragm to balance internal and external pressure at different depths

  • NEMA flange design for universal compatibility

Motor cooling is achieved by the surrounding water flowing past the motor housing. The pump must be fully submerged below the minimum water level before starting.

Power and Control Options

Power typeOptionsSuitability
Single‑phase AC (230V / 240V)Up to 2.2 kWDomestic wells, residential water supply, small farms
Three‑phase AC (400V / 415V / 690V)2.2 – 350 kWAgricultural irrigation, industrial, municipal, mining
Solar DC (solar‑ready models)Direct PV connection (with/without inverter)Off‑grid areas, remote boreholes, drought‑prone regions

Control and protection:

  • Control box with starting capacitor and thermal device (single‑phase models)

  • Motor protection via thermal sensors (PTC thermistors) and moisture detection in oil chamber

  • Variable frequency drive (VFD) compatible on three‑phase models for variable flow applications

  • Soft starter option for large motors (reduces starting current)

  • Dry‑run protection via pressure switch or level control relay

Mechanical Seal – Dual Seals with Oil Chamber

The motor is sealed from the pumped liquid by a mechanical seal system, typically a dual seal arrangement with an intermediate oil chamber:

Seal positionSeal facesElastomerLubrication
Lower seal (product side)Silicon carbide vs. silicon carbide (or tungsten carbide)NBR / FKMOil from chamber
Upper seal (motor side)Carbon vs. ceramicNBR / FKMClean oil in chamber
Intermediate oil chamberDielectric oil, moisture sensor—Contains & lubricates seals

Features:

  • Oil chamber acts as a barrier, protecting the motor from pumped liquid

  • Moisture sensor detects water ingress and alerts before motor damage

  • Silicon carbide seal faces are standard – extremely hard (Richwell >900Hv), providing long life even in abrasive water

  • Sand shield protects the lower seal from abrasive particles

Quality Assurance and Testing

All submersible borehole pumps undergo rigorous testing per international standards:

TestStandardDescription
Hydrostatic testAPI 610 / ISO 9906Casing and housing tested at 1.5x maximum operating pressure
Performance testISO 9906:2012 Grade 3BFlow, head, power efficiency measured at rated speed
Dielectric testIEC 60034Motor insulation integrity
Seal integrity testManufacturer standardOil chamber pressure test before assembly
Material certificationEN 10204 3.1Full traceability for pressure‑containing components

Applications

IndustryApplicationTypical Pump Size
Municipal water supplyGroundwater extraction for drinking water6″–12″, 15–200 kW
Agricultural irrigationCenter pivot, sprinkler systems, drip irrigation, livestock water4″–10″, 5–110 kW
MiningMine dewatering, groundwater control, quarry drainage6″–8″, 30–200 kW (MSHA/ATEX optional)
ConstructionGroundwater lowering for foundation excavation4″–8″, 5–75 kW (portable)
IndustrialProcess water supply, cooling water, wash‑down systems4″–8″, 5–90 kW
Domestic / residentialSingle‑family homes, rural housing, small housing developments4″, 0.37–2.2 kW (single‑phase)

Installation Guidelines

Borehole preparation:

  • The borehole must be straight, vertical, and free of obstructions.

  • Minimum borehole diameter must exceed pump OD by 10‑20 mm (0.4″–0.8″).

  • For 4″ pumps, minimum borehole diameter is 100 mm (3.9″). For 3″ slim‑line models, minimum diameter is 76 mm (3.0″).

Installation steps:

  1. Assemble pump to motor (close‑coupled via NEMA flange).

  2. Lower the pump assembly into the borehole using the discharge pipe as support.

  3. Secure with a clamp at the wellhead.

  4. Connect the electric cable to the surface control box.

  5. Fill the borehole with water (if dry) before starting the first time.

  6. Start the pump with the discharge valve partially closed; slowly open to operating point.

Important:

  • Never run the pump dry – mechanical seal and motor bearings are water‑lubricated and depend on the pumped liquid.

  • Pump must be fully submerged and set below the dynamic water level to ensure cooling flow.

  • For sandy bores, install a sand trap or pre‑filter between the pump and well casing.

Maintenance Schedule

TaskFrequency
Check motor insulation resistanceAnnually (or if moisture alarm triggers)
Measure pump flow and head (compare to curve)Annually
Inspect electrical cable for damageAnnually
Check control box / starter contactsAnnually (single‑phase models)
Replace mechanical sealsWhen moisture alarm triggers or at major overhaul (10,000‑15,000 hours)
Lift pump and inspect impellers, diffusers, wear rings15,000‑20,000 hours or when performance degrades

Troubleshooting

ProblemLikely CauseSolution
Pump does not startNo power, control box fault, thermal overload trippedCheck breaker, fuses, capacitor; reset thermal
Pump starts but no waterPump set below static water level? – check water level; blocked discharge pipe; impellers jammedRaise pump; clear blockage; pull pump and clean
Low flow / headWorn impellers, wear rings, or diffusers; sand or debris blocking stages; voltage dropPull pump; inspect and replace worn parts; clean stages; check supply voltage
Overcurrent (motor trips)Pump running dry, fluid density too high, voltage imbalance, pump not fully submergedEnsure submerged; check water quality; check supply
Moisture alarm (oil chamber)Mechanical seal leakPull pump; replace seal kit and oil immediately

Why Choose Our Submersible Borehole Pump?

  • Multi‑stage diffuser design – High head (up to 780 m) in compact vertical format.

  • Stainless steel wetted parts (AISI 304 / 316 / duplex) – Corrosion‑resistant, even in aggressive groundwater.

  • NEMA standard motors – Interchangeable with major brands; IP68 submersible; thermal and moisture protection included.

  • Floating impeller design – Self‑adjusting for wear, optimised performance, easy starting, long service life in abrasive sandy water.

  • Single‑phase (230V) models up to 2.2 kW – Direct connection to residential power, no three‑phase needed.

  • Three‑phase (400V / 690V) up to 350 kW – For large boreholes with high flow and head demands.

  • Solar DC ready models – Off‑grid operation in remote areas - operates directly from PV panels or batteries.

  • Sand‑tolerant hydraulics – Handles up to 0.25% sand content without rapid wear.

  • World‑wide spindle compatibility – NEMA flange pattern matches Franklin Electric, Grundfos, and other major motor brands.

  • ISO 9906 performance certified – Guaranteed real‑world efficiency.

  • CE, UL, and ATEX options available – For explosive environments (methane in mining).

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity for 10 years Minimum order (MOQ) pricing available for bulk
Mechanical seal kit (lower + upper) = 1 set per pump; inquire for bulk pricing1 set (contact for custom)
Floating impeller set (complete stages)1 set (all stages)
Diffuser set (complete stages)1 set (all stages)
Stage wear ring set1 set (all stages)
Motor O‑ring / gasket kit1 set (complete)
Control box / capacitor1 (for single‑phase models)

Get a Quote or Engineering Support

For detailed selection of the correct submersible borehole pump for your application – including borehole diameter, depth and flow/head requirements, water chemistry (corrosiveness, sand content), power supply, and installation conditions – please contact our engineering team.

Email: info@hyrig.com

Our engineers support municipal water supply, agricultural irrigation, mining dewatering, and industrial water projects worldwide with reliable, high‑efficiency submersible borehole pumps – stainless steel, NEMA motors, built for deep well service.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit