Submersible Sewage Pump – Vortex & Channel Impeller for Wastewater & Sludge

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Submersible sewage pump for raw wastewater, sludge, and solids‑laden liquids. Vortex (non‑clog) or channel (wear‑resistant) impeller options. Passes solids up to 80 mm. Flows to 2,000 m³/h, heads to 80 m, motor to 315 kW. Cast iron or stainless steel construction. Built‑in thermal protection, double mechanical seal with oil chamber, IP68 rating. Ideal for municipal wastewater, industrial effluent, lift stations, and flood control.

Conatct For Details
DetailReview(0)Additional

Product Overview

A submersible sewage pump is a rugged centrifugal pump designed to operate fully submerged in raw wastewater, sewage, sludge, and industrial effluent. Unlike clean water pumps, sewage pumps are engineered to pass soft solids (rags, wipes, fecal matter, organic debris) and withstand abrasive particles without clogging. The motor is hermetically sealed, oil‑filled or water‑filled, and cooled by the surrounding liquid. The pump is typically installed in a wet well (lift station) or submersible pump pit, connected to guide rails for easy removal and maintenance.

These pumps are the backbone of municipal wastewater collection systems, industrial effluent treatment plants, flood control stations, and construction dewatering where solids are present.

Key Pump Configurations – Impeller Types

Impeller TypeSolids HandlingEfficiencyBest Application
Vortex (recessed)Excellent – passes large, stringy solids without cloggingLower (40‑60%)Raw sewage, unscreened wastewater, high solid content
Channel (single or multi‑vane)Good – passes moderate solids (up to 80mm)Higher (60‑75%)Screened sewage, sludge, industrial effluent
Semi‑open / multi‑vaneModerate – for light solidsMedium‑highDrainage with some debris, stormwater
GrinderReduces solids to small particles before pumpingLowPressure sewer systems with small diameter pipes

For most raw sewage applications, the vortex impeller is preferred because the recessed design creates a whirlpool that draws solids into the pump without the impeller touching them – virtually eliminating clogging. For higher efficiency with screened sewage or sludge, a channel impeller provides better energy performance.

Key Technical Specifications

ParameterRange
Flow range5 – 2,000 m³/h (22 – 8,800 GPM)
Head range5 – 80 m (16 – 260 ft)
Motor power1.5 – 315 kW (2 – 420 HP)
Solids handling (vortex impeller)Up to 80 mm (3″) spherical solids
Solids handling (channel impeller)Up to 50 mm (2″)
Voltage / frequency400V / 50Hz or 460V / 60Hz three‑phase (single‑phase small units optional)
Speed1,450 / 2,900 rpm (50Hz) ; 1,750 / 3,500 rpm (60Hz)
Maximum submersion depth20 m (standard) , up to 50 m on request
Liquid temperature0 – 40°C (standard) , up to 90°C with special sealing
pH range5 – 9 (standard) ; wider with stainless steel
Protection classIP68 (continuous submersion)
Insulation classF or H
Motor coolingJacket cooling (standard) or external cooling shroud (dry well)

Materials – Abrasion & Corrosion Resistance

ComponentStandard MaterialUpgrade Option
Pump casing / voluteCast iron (GG25 / ASTM A48)Ductile iron, stainless steel 316
Impeller (vortex or channel)Cast iron (hardened)Ni‑hard, stainless steel, high‑chrome alloy
ShaftStainless steel (AISI 420 / EN 1.4021)AISI 316, duplex
Wear rings (if fitted)Cast ironStainless steel, hard coating
Mechanical sealCarbon / silicon carbide (oil‑cooled)Silicon carbide / silicon carbide (for abrasives)
FastenersStainless steel–
Cable entryResin sealed with strain relief–

For aggressive industrial effluent (low pH, high chlorides) or abrasive sand‑laden sewage, select stainless steel or high‑chrome materials.

Mechanical Seal System – Dual Seal with Oil Chamber

Submersible sewage pumps use a double mechanical seal arrangement with an intermediate oil chamber. This design is critical for reliability:

  • Lower seal (product‑side) – Silicon carbide vs. silicon carbide (hard faces) , immersed in the pumped liquid. Resists abrasion.

  • Upper seal (motor‑side) – Carbon vs. ceramic or silicon carbide, runs in clean oil.

  • Oil chamber – Contains dielectric oil that lubricates the seals, transfers heat, and provides a moisture barrier. A moisture sensor (probe) detects water ingress and alarms before motor damage.

This dual seal system allows the pump to handle abrasive and corrosive sewage while protecting the motor. For highly abrasive service, specify tungsten carbide vs. silicon carbide seals.

Motor Features – Built for Continuous Duty

  • Fully submersible motor – IP68, tested at maximum depth.

  • Thermal sensors (PTC or thermistors) embedded in stator windings – trip motor if overheating.

  • Moisture sensor in oil chamber – alerts to seal failure.

  • Bearing temperature monitor (optional for large pumps).

  • Cooling system – Jacket cooling (heat transferred to pumped liquid) is standard; external cooling shroud required for dry pit installation or when pump is not fully submerged.

  • Motor protection class – Class F insulation (155°C) , Class H optional.

Pump Hydraulics – Optimized for Solids

Vortex impeller design:

  • Impeller is recessed away from the flow path.

  • Creates a vortex that pulls solids through the pump without impeller contact.

  • Very low NPSHr.

  • Ideal for raw unscreened sewage, stringy materials (rags, wipes).

  • Efficiency is lower (40‑60%) but clog‑free operation reduces downtime.

Channel (single‑vane or multi‑vane) impeller:

  • Smooth, open channels for solids passage.

  • Higher efficiency (60‑75%) – reduces energy consumption.

  • Suitable for screened sewage, sludge, industrial effluent with moderate solids.

  • Available with wear‑resistant hard coating.

Grinder pump:

  • Cutter bar and impeller with sharp edges reduce solids to 6‑8 mm.

  • Used in pressure sewer systems (small diameter pipes) and low‑flow lift stations.

Guide Rail System – Easy Installation & Removal

Most submersible sewage pumps are installed on a guide rail system in a wet well:

  1. A fixed discharge base (elbow) is mounted at the bottom of the wet well, connected to the discharge pipe.

  2. Guide rails (two pipes) run from the top of the well down to the base.

  3. The pump is lowered onto the guide rails using a chain.

  4. When the pump reaches the bottom, it automatically couples to the discharge base via a duck‑foot coupling.

  5. To remove, pull up the chain; the pump disengages.

This system allows one person to remove a pump weighing hundreds of kilograms without entering the wet well.

Applications

ApplicationTypical Pump SizeImpeller Type
Municipal wastewater lift station5 – 500 kWVortex (raw sewage)
Wastewater treatment plant (inlet / return sludge)10 – 200 kWChannel (screened) or vortex
Industrial effluent pumping5 – 150 kWStainless steel vortex or channel
Flood control / stormwater pumping50 – 315 kWChannel (high flow)
Construction dewatering (dirty water)1.5 – 30 kWSemi‑open (small solids)
Portable sewage bypass pumping5 – 150 kWVortex (trailer‑mounted)
Pressure sewer system (grinder)1 – 5 kWGrinder (cutter)

Key Features – Why Choose Our Submersible Sewage Pump

  • Clog‑free operation – Vortex impeller eliminates clogging in raw sewage; channel impeller offers higher efficiency for screened applications.

  • Dual mechanical seals – Silicon carbide faces for long life; oil chamber with moisture sensor.

  • IP68 submersible motor – Thermal sensors, moisture probe, IP68 cable entry.

  • Guide rail system – Easy installation and removal; no well entry required.

  • Wide solids handling – Passes spherical solids up to 80 mm.

  • Corrosion / abrasion resistant options – Cast iron, stainless steel, high‑chrome impellers.

  • Efficient hydraulics – Optimised impeller and volute for lowest energy consumption.

  • ATEX certified – Available for explosive atmospheres (Zone 1, Zone 2).

  • VFD ready – Suitable for variable frequency drive operation (consult for minimum speed).

  • Global standards – CE, EN 12050 (wastewater lifting plants), NSF/ANSI 61 (potable water contact – for clean water versions).

Quality Assurance and Testing

  • Hydrostatic test – Casing tested at 1.5x maximum working pressure.

  • Performance test – Water at rated speed per ISO 9906 Grade 3 (or Grade 2 on request).

  • Mechanical run test – 1 hour minimum, including vibration and temperature check.

  • Electrical test – Insulation resistance, polarity, and hi‑pot test.

  • Seal integrity test – Oil chamber pressure‑tested before assembly.

  • Material certification – EN 10204 3.1 for wetted parts on request.

Installation and Operation Notes

Wet well installation (standard):

  • Pump sits on guide rail base, fully submerged.

  • Ensure minimum submergence to avoid vortexing (see curve).

  • Provide high‑level and low‑level floats or ultrasonic level sensor.

Dry pit installation (optional):

  • Pump installed in a dry pump room with flooded suction.

  • External cooling shroud required for motor cooling.

Important operating rules:

  • Never run pump dry – seals and bearings will fail within minutes.

  • Do not start pump against a closed discharge valve for more than a few seconds.

  • Maintain minimum flow to avoid overheating (see manufacturer's curve for MCSF).

Maintenance

TaskFrequency
Check motor current and vibrationMonthly
Inspect cable for damageAnnually (or when pump is pulled)
Check oil chamber moisture sensorEach time pump is pulled
Change dielectric oil10,000 hours or 3 years (if no leaks)
Replace mechanical sealsWhen moisture alarm occurs or at major overhaul (20,000 hours)
Clean impeller and voluteAs needed (when flow drops)

Troubleshooting

ProblemLikely CauseSolution
Pump does not startNo power, thermal overload tripped, control float stuckCheck breaker, thermal reset, float operation
Pump runs but no flowImpeller clogged, check valve stuck, discharge line blockedPull pump; clean impeller; inspect check valve
Low flow / headWorn impeller or wear rings, partial blockageInspect and replace worn parts; clean pump
Motor overload (overcurrent)Impeller partially blocked, fluid density too high, phase lossClean impeller; check fluid; verify supply
Moisture alarmMechanical seal leakPull pump; replace seals; change oil
Excessive vibrationImpeller clogged or damaged, bearing wearClean or replace impeller; check bearings

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal set (lower + upper)1 set
Impeller (vortex or channel)1
Wear ring set (if fitted)1 set
Oil chamber gasket / O‑ring kit1 set
Moisture sensor probe1
Cable (complete with connector)1 (for spare)

Why Choose Our Submersible Sewage Pump?

  • Reliable clog‑free operation – Vortex impeller handles rags and wipes without failure.

  • Dual silicon carbide seals – Proven in abrasive sewage service, long life.

  • IP68 fully submersible – No risk of flood damage.

  • Easy guide rail installation – One‑person removal and replacement.

  • Wide range – Flows to 2,000 m³/h, heads to 80 m, powers to 315 kW.

  • Corrosion‑resistant options – Stainless steel for aggressive industrial waste.

  • ATEX available – For explosive environments like methane‑rich sewage.

  • Global support – Spare parts and field service worldwide.

Get a Quote or Engineering Support

For detailed selection of the correct submersible sewage pump – including flow/head requirements, solids size and type, wet well dimensions, power supply, and materials – please contact our engineering team.

Email: info@hyrig.com

Our engineers support municipal wastewater, industrial effluent, and flood control projects worldwide with reliable, clog‑resistant submersible sewage pumps – built for the toughest solids and longest service life.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit