The Sulzer OHH is an API 610 (ISO 13709) Type OH2 overhung, horizontal, single stage, centerline mounted, radially split process pump. It has the broadest performance range in the industry for Type OH2 pumps and is used in heavy-duty refinery, petrochemical, gas processing, and offshore oil production services. When applied as a nitric acid pump, the OHH reliably transfers nitric acid (HNO₃) in fertilizer plants, ammonium nitrate units, and chemical processing facilities.
The OHH features a radially split casing with end-suction, top-discharge configuration, centerline mounting for uniform thermal expansion, and back pull-out design allowing internal component removal without disturbing piping or driver.
As a specialized China API 610 pump manufacturer, we supply Sulzer OHH nitric acid pumps with corrosion‑resistant materials tailored to specific nitric acid concentrations and temperatures.
| Concentration | Temperature | Recommended Material |
|---|---|---|
| ≤30%, ambient | Standard operating range | 304L / 316L stainless steel |
| 30–70%, ambient | Standard range | 316L stainless steel (with corrosion allowance) |
| ≤98%, ≤40°C | Within OHH temperature limits | 316L or 904L |
| ≤98%, ≤80°C | Near upper OHH operating limit | High silicon stainless steel (SS920/SS940) |
| All concentrations, elevated temperature | Special consideration | 904L, high silicon SS, or Alloy 20 |
Nitric acid is an oxidizing medium. Chromium and silicon provide oxidation resistance; stainless steels and materials containing Si and Cr are ideal for concentrated nitric acid resistance.
316L stainless steel – suitable for dilute and moderate nitric acid up to 60°C
904L super austenitic stainless steel – suitable for various concentrations up to boiling point
High silicon stainless steel (SS920/SS940) – recommended for concentrated hot nitric acid (98%, 80°C). High silicon content provides excellent resistance in strongly oxidizing environments up to approximately 93% at elevated temperatures.
High silicon cast iron (STSi15R) – alternative for less critical services, suitable for all temperatures below 93% concentration.
Not suitable: Carbon steel, cast iron, aluminum, copper alloys — all corrode rapidly in nitric acid service.
Elastomers: Use PTFE or FKM (Viton) for gaskets and O‑rings; EPDM and Buna‑N are not suitable.
| Parameter | Sulzer OHH Standard Range | Notes for Nitric Acid Service |
|---|---|---|
| Capacities | Up to 2,250 m³/h | Select based on plant acid flow |
| Heads | Up to 360 m | Typically 30–150 m for acid transfer |
| Pressures | Up to 75 bar | Nitric acid service typically <20 bar |
| Temperature | -75°C to +425°C | Concentrated acid <80°C; dilute ambient |
| Discharge sizes | 25 to 400 mm | Depends on flow requirements |
| Max speed | Up to 3,600 rpm | Standard at 2,950/2,980 rpm |
| Flange rating | ASME Class 150 / 300 standard; 600 optional | Class 300 recommended for concentrated acid |
| NSS | 11,000 standard (improved suction optional) | Beneficial for low NPSH availability |
For concentrated nitric acid service, high silicon stainless steel (SS920/SS940) is the recommended material. 904L is suitable for low to medium concentration and moderate temperature.
| Component | Dilute/Cold Acid (≤30%) | Concentrated Hot Acid (98%, 80°C) |
|---|---|---|
| Casing | 316L stainless steel | High silicon SS (SS920/SS940) / 904L |
| Impeller | 316L stainless steel | High silicon SS / 904L |
| Shaft | 17-4PH stainless steel | 17-4PH or Alloy 20 / Hastelloy C‑276 |
| Wear rings | 316L with Stellite facing (or omit) | High silicon SS with hard facing |
| Flange bolting | A193 B8M (316 SS) | A193 B8M Class 2 |
| Gaskets / O‑rings | PTFE or FKM | PTFE or FFKM (Kalrez) |
Material notes: Ensure low carbon content in 316L to prevent carbide precipitation. Add corrosion allowance of 2‑3 mm for extended service life. Avoid copper‑bearing alloys. For concentrated hot acid, high silicon materials are required.
The Sulzer OHH frame accommodates the following API 610 material classes for nitric acid and corrosive chemical services: S‑4, S‑5, S‑6, S‑8, C‑6, A‑8, D‑1, D‑2.
S‑4 to S‑8 – austenitic stainless steels (304, 316, high silicon grades)
C‑6 – duplex stainless steel
A‑8 – Alloy 20 (CN7M) – suitable for many nitric acid applications
D‑1 / D‑2 – higher alloys (Hastelloy, others) for severe corrosion conditions
| Feature | Benefit for Nitric Acid Service |
|---|---|
| Back pull-out design | Rotating assembly removable without disturbing acid piping; reduces maintenance time and chemical exposure risk |
| Centerline mounting | Uniform thermal expansion; prevents misalignment during temperature cycling up to 80°C |
| Radially split casing | Robust pressure containment; easy to inspect and clean; acid‑resistant materials |
| Rigid shaft with minimal deflection | Extends mechanical seal and bearing life; critical for low lubricity nitric acid |
| Closed impeller (dynamically balanced) | High efficiency; renewable wear rings extend casing life |
| API 682 seal chamber | Accommodates single seal (Plan 11) for dilute acid, or double seal (Plan 53B) for concentrated/hazardous acid |
| Finned bearing housing with fan cooling | Long bearing life under continuous hot acid pump operation |
| Heavy‑duty baseplate | Designed to 2x ISO 13709 nozzle load requirements; minimizes vibration |
| Service | Recommended Seal Configuration | Flush Plan |
|---|---|---|
| Dilute nitric acid (<30%) | Single mechanical seal | Plan 11 |
| Moderate concentration (30–60%) | Single or tandem seal | Plan 11 or Plan 21 |
| Concentrated acid (>60% to 98%) | Tandem or double seal | Plan 52 or Plan 53B |
| Fuming red nitric acid | Double seal | Plan 53B |
| Hot acid (>60°C) | Tandem seal | Plan 52 |
Seal faces: Silicon carbide vs. carbon (standard); tungsten carbide vs. carbon (abrasive or high temperature). Secondary seals: FKM, PTFE, or FFKM.
Calcium Ammonium Nitrate (CAN) plant (P‑301): Nitric acid transfer from absorption tower to neutralizer
Nitric acid plant circulation: Weak acid to bleacher, strong acid to storage
Ammonium nitrate plant: Acid feed to neutralization reactor
Phosphate fertilizer complex: Nitric acid for phosphate rock digestion
Chemical processing: Nitration reactions, acid recovery systems
Full API 610 12th Edition (ISO 13709) compliance
Broad hydraulic coverage – up to 2,250 m³/h, 360 m head
Multiple corrosion‑resistant alloys – 316L, 904L, high silicon SS, Alloy 20
API 682 seal compatibility for zero leakage
Back pull-out design – easy maintenance without disturbing piping
Centerline mounting – thermal stability for hot acid service
Cost‑effective alternative to Western imports
Lead time: 20–28 weeks for standard stainless steel
Factory testing: hydraulic performance, mechanical run, hydrostatic
Complete documentation: curves, drawings, API datasheets, material certifications
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type OH2 – horizontal, overhung, single stage, radially split, centerline mounted |
| Standard | API 610 12th Edition (2020) & ISO 13709 |
| Medium | Nitric acid (HNO₃) – dilute to concentrated (up to 98%) |
| Capacities | Up to 2,250 m³/h |
| Heads | Up to 360 m |
| Temperature | -75°C to +425°C (acid service typically ≤80°C) |
| Pressure rating | Up to 75 bar |
| Materials (wetted) | 316L, 904L, high silicon SS, Alloy 20, Hastelloy |
| Seals | API 682 Plan 11/21/52/53B |
| Flange rating | ASME Class 150 / 300 / 600 |
| Lubrication | Oil ring self‑lubricating |
| Maintenance | Back pull‑out design |
For more information or a custom proposal for your nitric acid pump (Sulzer OHH) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.