O-Ring Set for Seal 0600-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

2026-03-15 15:10

O-Ring Set for Seal 0600-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

Product Overview

HYRIG's O-Ring Set for Seal (Part No. 0600-200400) is engineered as a direct replacement for Sulzer BBS 200-400 centrifugal pumps, fully complying with API 610 standards. This precision-manufactured seal O-ring kit ensures leak-free performance, perfect dimensional fit, and long-term reliability in industrial pumping applications—equivalent to Sulzer's original specifications at a cost-effective price point.

Designed specifically for the seal assembly of Sulzer BBS 200-400 pumps, the kit includes all required O-rings for a complete seal service, eliminating the need for multiple part purchases. Our O-rings are crafted with industry-proven materials to resist corrosion, temperature fluctuations, and mechanical wear, extending maintenance intervals and reducing downtime.


Key Specifications

ItemDetails
Part Number0600-200400
Compatible Pump ModelSulzer BBS 200-400 (API 610 Centrifugal Pump)
ApplicationSeal Assembly Maintenance/Replacement
Kit ContentsPrecisely sized O-rings for seal housing, gland, and adapter (complete set for one pump seal)
Dimensional ToleranceComplies with JIS B 2401 and ISO 3601 standards
Cross-Section DiameterMatched to Sulzer original design (optimized for seal groove fit)

Material Options & Compatibility

Choose the ideal material based on your pumped media and operating conditions—all materials meet industrial sealing requirements and are compatible with Sulzer BBS 200-400's seal system:

MaterialOperating Temperature RangeKey PropertiesRecommended Applications
NBR (Nitrile Rubber)-30°C to 100°C (-22°F to 212°F)Excellent oil resistance, good tensile strength (JIS HS 70±5)Petroleum products, mineral oils, water-based fluids, general industrial media
FKM (Viton® Fluoroelastomer)-15°C to 200°C (5°F to 392°F)Superior chemical/corrosion resistance, high temperature stabilityStrong acids, alkalis, solvents, aggressive chemicals, high-temperature fluids
EPDM (Ethylene-Propylene)-40°C to 120°C (-40°F to 248°F)Outstanding weather/ozone resistance, compatibility with polar mediaWater, steam, weak acids/alkalis, HVAC fluids
PTFE-Coated NBR-20°C to 150°C (-4°F to 302°F)Low friction, enhanced chemical resistanceAbrasive media, high-pressure applications (up to 20MPa)

Reference: Material compatibility aligns with industry standards (Sterlitech O-Ring Compatibility Chart and eFunda Chemical Compatibility Ratings).


Replacement Guidelines & Installation Best Practices

When to Replace

  • Visible signs of wear: cracks, hardening, deformation, or extrusion

  • Seal leakage (exceeds 3 drops/minute)

  • During scheduled seal maintenance (recommend replacing O-rings even if undamaged—old O-rings lose elasticity over time)

  • After exposure to contaminated media or temperature spikes

Step-by-Step Installation (Avoid Common Failures)

Pre-Installation Preparation

  1. Depressurize the pump system and disconnect power to ensure safety.

  2. Thoroughly clean the seal groove, gland, and mating surfaces—remove oil, debris, and rust (use a solvent or compressed air).

  3. Inspect the seal groove for burrs, scratches, or corrosion (smooth with fine sandpaper if needed).

Installation Process

  1. Always use new O-rings (never reuse old ones).

  2. Lightly lubricate O-rings with compatible fluid (same as pumped media or silicone grease)—dry installation causes cuts and leaks.

  3. Gently stretch O-rings evenly (avoid over-stretching to prevent rebound failure) and place into the groove.

  4. Ensure O-rings are fully seated, not twisted or misaligned (twisting leads to premature leakage).

  5. Use a protective sleeve when passing O-rings over threads or sharp edges to avoid cuts.

Post-Installation Check

  1. Reassemble the seal assembly and torque bolts evenly (follow Sulzer's recommended torque values).

  2. Gradually repressurize the system and inspect for leaks.

  3. For high-pressure applications (>20MPa), install backup rings (included in optional premium kits) on the low-pressure side.


Why Choose HYRIG's 0600-200400 O-Ring Set?

  • Perfect Fit: Engineered to match Sulzer BBS 200-400's seal dimensions—no modification required for installation.

  • Durability: Industrial-grade materials with strict quality control (tensile strength ≥9.8MPa, elongation ≥200%).

  • Cost-Effective: Direct replacement for Sulzer original parts at a competitive price, without compromising performance.

  • Convenience: Complete kit with all necessary O-rings—simplifies procurement and maintenance.

  • Reliability: Backed by HYRIG's quality guarantee—compatible with original seal components and API 610 operational requirements.


Order & Inquire

For pricing, availability, or custom material requests (e.g., extreme temperature/corrosion resistance), contact our technical sales team:

Email: info@hyrig.com

Please include your pump's serial number and operating conditions for personalized recommendations.


Name:
Message:
Verification code:
Submit
Comment