Double Suction Impeller 1100-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

2026-03-15 17:25

Double Suction Impeller 1100-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

Product Overview

HYRIG's Double Suction Impeller (Part No. 1100-200400) is a precision-engineered direct replacement for Sulzer BBS 200-400 centrifugal pumps, fully adhering to API 610 standards for industrial centrifugal pump design and performance. As a core hydraulic component of the BBS 200-400 series, this double suction impeller delivers balanced axial thrust, high flow capacity, and efficient fluid transfer—matching Sulzer's original design specifications in dimensions, hydraulic performance, and material quality, while offering cost-effective value.

Crafted for reliable operation in demanding industrial environments (chemical processing, petroleum refining, power generation, and water treatment), the impeller features a symmetric double suction structure that minimizes vibration, reduces bearing load, and extends the pump's overall service life. Each unit undergoes strict quality control, including dynamic balance testing and dimensional inspection, to ensure seamless integration with Sulzer BBS 200-400 pump assemblies.


Key Specifications

ItemDetails
Part Number1100-200400
Compatible Pump ModelSulzer BBS 200-400 (API 610 Centrifugal Pump)
Pump TypeDouble Suction Centrifugal Pump
Design StandardAPI 610 (12th Edition)
Structure FeatureSymmetric double suction design (axial thrust self-balanced)
Hydraulic PerformanceMatches Sulzer original: Flow rate, head, and efficiency identical to OEM specifications
Precision StandardDynamic balance: ISO 1940 G2.5 (critical speed compliance)
Dimensional ToleranceComplies with ISO 2768-m and DIN 40683 standards
Shaft ConnectionKeyway fit (matches Sulzer BBS 200-400 shaft dimensions)

Material Options & Application Suitability

Choose the optimal material based on your pumped media, temperature, and abrasion/corrosion conditions—all materials are engineered for double suction impeller's high-pressure, high-flow operating demands:

MaterialOperating Temperature RangeKey PropertiesRecommended Applications
Cast Iron (HT250)-20°C to 120°C (-4°F to 248°F)Cost-effective, good machinability, moderate wear resistanceClean water, low-solids fluids, non-corrosive general industrial applications
Stainless Steel 304-50°C to 300°C (-58°F to 572°F)Excellent corrosion resistance, good tensile strength (≥515MPa)Mild acids, alkalis, food-grade fluids, freshwater, and low-chloride media
Stainless Steel 316L-50°C to 350°C (-58°F to 662°F)Superior corrosion resistance (chloride, sulfuric acid), high ductilitySeawater, chemical solvents, pharmaceuticals, aggressive industrial fluids
Duplex Steel 2205-40°C to 315°C (-40°F to 600°F)High strength (yield strength ≥450MPa), excellent abrasion/corrosion resistanceOil & gas production, desalination, mining slurries, high-sulfur media
Hastelloy C276-20°C to 450°C (-4°F to 842°F)Exceptional resistance to strong acids (HCl, H2SO4), chlorides, and oxidizing agentsSevere corrosion environments, chemical processing, petrochemical refining

*Material certification available upon request (including mill test reports, EN 10204 3.1/B).*


Replacement Guidelines & Installation Precautions

When to Replace

  • Impeller blade wear exceeds 1mm (measured at the blade tip)

  • Visible cracks, pitting, or erosion on blade surfaces or hub

  • Pump efficiency drops by >10% (compared to original performance data)

  • Imbalance-induced vibration (vibration velocity >2.8mm/s at pump bearing)

  • Cavitation damage (pitting on blade leading edges)

  • After prolonged operation in abrasive media (recommended 2-3 year preventive replacement for critical applications)

Installation & Maintenance Best Practices

Pre-Installation Inspection

  1. Verify impeller part number, material, and dimensional fit with pump casing (reference Sulzer BBS 200-400 maintenance manual).

  2. Check for transportation damage (scratches, dents) and ensure impeller rotates freely without binding.

  3. Confirm dynamic balance certification (included with each unit) meets ISO 1940 G2.5 standards.

Installation Process

  1. Clean the pump shaft, keyway, and impeller hub thoroughly—remove rust, debris, or old gasket material.

  2. Apply a thin layer of anti-seize compound to the shaft (compatible with impeller material) to facilitate future removal.

  3. Align the impeller keyway with the shaft key, then slide the impeller onto the shaft until fully seated against the shaft shoulder.

  4. Torque the impeller nut to Sulzer's recommended specification (typically 80-120 N·m for BBS 200-400) using a torque wrench—avoid over-tightening to prevent hub deformation.

  5. Install the impeller wear ring (sold separately or as part of HYRIG's Wear Parts Kit) and verify clearance (0.2-0.5mm, per API 610 requirements).

Post-Installation Validation

  1. Perform static rotation test to ensure no contact between impeller and casing/wear ring.

  2. Conduct pump performance test (flow rate, head, power consumption) to confirm alignment with design specifications.

  3. Monitor vibration and temperature during initial operation (first 24 hours) to detect potential misalignment.


Why Choose HYRIG's 1100-200400 Double Suction Impeller?

  • Perfect Hydraulic Match: Engineered to replicate Sulzer's original hydraulic design, ensuring identical flow, head, and efficiency.

  • Precision Manufacturing: CNC-machined blades and hub for tight tolerances, paired with ISO 1940 G2.5 dynamic balance for low vibration.

  • Durable Materials: Industrial-grade alloys with corrosion/abrasion resistance tailored to harsh operating conditions.

  • Direct Replacement: No modifications required—fits seamlessly with Sulzer BBS 200-400 pump casings, shafts, and wear rings.

  • Quality Guaranteed: 12-month warranty against material defects and manufacturing errors; full technical support available.


Order & Inquire

For pricing, material availability, lead time, or custom material requests (e.g., high-temperature alloys), contact HYRIG's technical sales team:

Email: info@hyrig.com

Please include your pump model, serial number, and operating conditions for personalized recommendations.



Name:
Message:
Verification code:
Submit
Comment