The SULZER SJD 7APC/19 is a vertical, suspended, double‑case, multistage can pump from Sulzer’s SJD series. It is specifically designed for very high head, medium flow applications where low NPSH is not the primary constraint (unlike the D‑version with double‑suction first stage). With 19 impeller stages, this pump achieves heads up to 850 metres, making it suitable for ultra‑high‑pressure duties in power generation and petrochemical industries. The SJD series offers two sub‑lines: SJD‑CEP (power condensate / boiler feed service) and SJD‑API (fully compliant with API 610 for refinery and chemical plant high‑pressure transfer).
Model Breakdown (SJD 7APC/19)
SJD – Vertical suspended double‑case multistage can pump series
7 – Hydraulic size code (approx. 7‑inch bowl / diffuser casing – smaller than the 9DHC model)
A – First‑stage single‑suction impeller (higher specific speed, larger flow capacity than double‑suction)
P – Material & pressure class: carbon steel casing, chrome steel internals, high‑pressure rating
C – Can & bearing configuration: standard can length, graphite self‑lubricating line shaft bearings
/19 – Number of impeller stages = 19 (very high head)
Key Technical Parameters (50 Hz, typical for 7APC/19 trim)
| Parameter | Value (CEP / API variant) |
|---|---|
| Model | SULZER SJD 7APC/19 |
| Pump type | Vertical multistage can pump (double‑case, suspended) |
| Flow range | 180 – 300 m³/h (medium flow) |
| Head range | 750 – 850 m (approx. 40‑45 m per stage × 19) |
| Number of stages | 19 |
| Speed | 2950 rpm (50 Hz) – high speed for high head |
| Max working pressure | 78 bar (7.8 MPa) – up to 80 bar typical |
| Temperature range | ≤ 100°C (SJD‑CEP) / ≤ 205°C (SJD‑API) |
| Materials | Outer can / Casing: Carbon steel; Inner casing / Diffusers: Chrome steel; Impellers: Chrome steel; Shaft: Chrome steel; Bearings: Carbon graphite (self‑lubricating) |
| Seal type | Mechanical seal (single or dual, API Plan as required) |
| NPSH characteristic | Moderate – first‑stage single‑suction impeller (higher NPSHr than double‑suction “D” version, suitable for systems with adequate NPSHa) |
Design & Performance Features
Extremely high head with 19 stages – Each stage contributes approx. 40‑45 m of head, totalling 750‑850 m. For even higher head, stage counts up to 30+ are possible in the SJD platform.
First‑stage single‑suction (Type A) – Compared to the double‑suction D version (e.g., 9DHC), the A impeller allows larger flow capacity (up to 300 m³/h) at slightly higher NPSH requirement. Ideal when NPSH is sufficient but flow and head must both be high.
Double‑case (can) construction – The outer can is a low‑pressure vessel supporting the inner assembly, which contains full discharge pressure. This design ensures safety, contains high‑pressure fluid in the inner core, and allows removal of the rotating element without disturbing the can or connected piping.
High‑pressure rating (P class) – Materials and wall thickness designed for up to 78 bar (7.8 MPa) working pressure, suitable for supercritical boiler feed or high‑pressure hydrocarbon transfer.
Self‑lubricating graphite line shaft bearings – Located at each stage and along the long shaft, these bearings run in the pumped fluid, requiring no external lubrication or maintenance for clean liquids (condensate, water, light hydrocarbons).
Extended coupling (long coupler) – The motor is mounted above the pump on a separate support structure. The long coupling allows removal and replacement of the mechanical seal and thrust bearings without lifting the motor or extracting the pump from the pit – critical for high‑availability plants.
API 610 compliance (SJD‑API version) – For petrochemical service, the SJD‑API meets API 610 (VS6 or VS7) requirements, including full pressure containment, high‑temperature rating (205°C), API 682 seal systems, and heavy‑duty thrust bearings.
Comparison with SJD 9DHC‑VC10A/6
| Feature | SJD 7APC/19 | SJD 9DHC‑VC10A/6 |
|---|---|---|
| Hydraulic size | 7 (smaller) | 9 (larger) |
| Stages | 19 | 6 |
| Head | 750‑850 m | 240‑300 m |
| Flow | 180‑300 m³/h | 250‑450 m³/h |
| First‑stage impeller | Single‑suction (A) | Double‑suction (D) |
| NPSHr | Moderate | Very low |
| Typical application | High head, medium flow | Low NPSH, medium head |
Typical Applications
Power Generation (SJD‑CEP)
High‑pressure condensate booster pump (for supercritical / ultra‑supercritical boilers)
Boiler feed water booster pump (pre‑feed to main boiler feed pump)
Heater drain pump (HP feedwater heater drains at high pressure)
Nuclear island reactor coolant fill / charge pump (high head)
Petrochemical & Oil & Gas (SJD‑API)
LPG / ethylene high‑pressure transfer and loading (up to 80 bar)
High‑pressure propane or butane pipeline booster pumps
Oilfield water injection (high pressure, medium flow)
Refinery high‑pressure process water injection (desalter, hydrotreater wash water)
Chemical reactor feed (e.g., methanol synthesis loop, high‑head hydrocarbon feed)
Why Choose SULZER SJD 7APC/19 for Very High Head, Medium Flow Service?
When you need heads approaching 850 m at moderate flow rates with vertical installation and limited floor space, the SJD 7APC/19 is an optimal solution. Its 19 stages pack high head into a single vertical can pump, avoiding the complexity of multiple pumps in series or high‑speed integrally geared units. The double‑case construction, chrome steel metallurgy, self‑lubricated graphite bearings, and long coupling design ensure reliability, safety, and ease of maintenance. Whether for supercritical power plants or high‑pressure LPG transfer, this pump delivers continuous, trouble‑free operation at extreme pressures.
Contact
For technical datasheets, stage configuration options, material selection, or quotation:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.