The SULZER SJD 9DHC‑VC10A/6 is a vertical, suspended, double‑case, multistage can pump from Sulzer’s SJD series. It is specifically engineered for applications demanding very low NPSH (Net Positive Suction Head), high head, and reliable operation with clean or slightly contaminated liquids. Typical duties include power plant condensate extraction (CEP), heater drain transfer, and petrochemical cryogenic/high‑pressure pumping. The SJD series is available in two sub‑lines: SJD‑CEP (designed for power generation condensate service) and SJD‑API (fully compliant with API 610 for refinery and petrochemical duties).
Model Breakdown (SJD 9DHC‑VC10A/6)
SJD – Vertical suspended double‑case multistage can pump series
9 – Hydraulic size code (approx. 9‑inch bowl / diffuser casing)
D – Multistage configuration with double‑suction first stage (low NPSH feature)
HC – Material & hydraulic combination: high head, carbon/chrome steel wetted parts
VC10A – Can length and bearing configuration (10‑stage equivalent length, graphite self‑lubricating bearings)
/6 – Number of impeller stages = 6
Key Technical Parameters (Typical for 9DHC/6 trim)
| Parameter | Value (CEP / API variant) |
|---|---|
| Model | SULZER SJD 9DHC-VC10A/6 |
| Pump type | Vertical multistage can pump (double‑case, suspended) |
| Flow range | 250 – 450 m³/h (typical) |
| Head range | 240 – 300 m (approx. 40‑50 m per stage ×6) |
| Number of stages | 6 |
| Speed | 1480 or 2950 rpm (50 Hz) – depending on driver |
| Max working pressure | 4.7 – 9.4 MPa (47 – 94 bar) – CEP lower, API higher |
| Temperature range | ≤100°C (SJD‑CEP) / ≤205°C (SJD‑API) |
| Materials | Can / Outer casing: Carbon steel; Inner casing / Diffusers: Chrome steel; Impellers: Chrome steel; Shaft: Chrome steel; Bearings: Carbon graphite (self‑lubricating) |
| Seal type | Mechanical seal (single or dual, API Plan dependent) |
| NPSH characteristic | Very low (first‑stage double‑suction impeller + long can) |
Design & Performance Features
Low NPSH design – The long can (VC10A length) immerses the first‑stage impeller below the liquid surface, combined with a double‑suction first‑stage impeller, significantly reducing NPSH requirement. Ideal for condensate, near‑saturated liquids, and boiling cryogenic fluids.
Double‑case (can) construction – The outer can (barrel) withstands minimal pressure; the inner casing (bowl assembly) contains full discharge pressure. This provides safety, ease of maintenance, and allows removal of the inner assembly without disturbing the can.
Multistage high head capability – 6 stages produce heads up to 300 m. Can be configured with more or fewer stages (e.g., /8, /10) for different head requirements.
Self‑lubricating graphite bearings – Located at each stage and along the line shaft, these bearings run in the pumped liquid, requiring no external lubrication – maintenance‑free for clean water/condensate service.
Extended coupling (long coupler) – The motor is mounted above the pump on a separate support. The long coupling allows removal and replacement of the mechanical seal and thrust bearings without lifting the motor or removing the pump from the pit – significantly reducing maintenance time.
API 610 compliance (SJD‑API version) – For petrochemical and refinery services, the SJD‑API meets API 610 (OH3/OH4 vertical inline or VS6/VS7 can pump) requirements, including full pressure containment, high‑temperature rating (up to 205°C), and API 682 seal systems.
Removable sealing housing – The throat bushing and stuffing box can be serviced without dismantling the suction or discharge piping.
Typical Applications
Power Generation (SJD‑CEP)
Condensate extraction pump (CEP) in thermal, combined cycle, and nuclear power plants
Heater drain pump (HP/LP feedwater heater drains)
Geothermal and solar thermal power plant working fluid pumps
Petrochemical & Oil & Gas (SJD‑API)
LPG / LNG booster pumps and transfer
Refinery tank farm and pipeline transfer (light hydrocarbons)
Depropaniser / debutaniser reboiler feed (low NPSH)
Crude oil and product pipeline booster pumps (low NPSH suction)
High‑pressure cryogenic service (ethylene, propylene, LNG)
Why Choose SULZER SJD 9DHC‑VC10A/6 for Low NPSH High‑Head Service?
No other horizontal pump can match the low NPSH capability of a vertical can pump. The SJD 9DHC‑VC10A/6 combines Sulzer’s proven hydraulic design with robust double‑case construction, self‑lubricating bearings, and easy‑maintenance features. Whether for power plant condensate or API 610 hazardous service, this pump delivers reliable, continuous operation at heads up to 300 m with exceptionally low NPSH requirements – reducing pit depth and avoiding cavitation damage.
Contact
For technical data sheets, selection assistance, or quotation:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.