The 1st Stage Reactor Feed Pump CP 4x6x9FX is a horizontal, heavy‑duty, single‑stage end‑suction centrifugal pump specifically engineered for high‑pressure reactor feed service in refineries, petrochemical plants, and hydrogenation units. It delivers feedstock (hydrocarbon liquids, gas oils, or chemical intermediates) from low‑pressure storage or pre‑treatment to the first stage of a high‑pressure reactor – typically a hydrocracker (HCU), hydrotreater (HDS), or catalytic reactor. The “CP” designation indicates an API 610 compliant centreline‑mounted, heavy‑duty process pump (Type OH2), designed for severe high‑temperature, high‑pressure, and potentially abrasive or corrosive services.
The model number 4x6x9FX follows industry convention:
4” – discharge nozzle size (DN100)
6” – suction nozzle size (DN150)
9” – nominal impeller diameter (approx. 229 mm)
FX – hydraulic trim variant (e.g., high efficiency, specific flow/head curve, or special metallurgy)
Key Technical Parameters
| Parameter | Value |
|---|---|
| Model | 1st Stage Reactor Feed Pump CP 4x6x9FX |
| Pump type | Horizontal single‑stage end‑suction, API 610 OH2 (centreline mounted, heavy duty) |
| Suction size | DN150 (6 inch) |
| Discharge size | DN100 (4 inch) |
| Impeller diameter | 229 mm (9 inch) |
| Flow range | 150 – 450 m³/h (typical) |
| Head range | 300 – 550 m (3.0 – 5.5 MPa) |
| Speed | 2950 – 3550 rpm (50/60 Hz) |
| Efficiency | 78% – 86% (BEP) |
| Shaft power | 200 – 600 kW |
| Motor power | 250 – 750 kW, IE3 / IE4, explosion‑proof for Class I Div 1/2 |
| Max working pressure | 6.0 – 8.0 MPa (casing rating dependent) |
| Temperature range | -20°C to 200°C (higher with special materials) |
| Materials (wetted parts) | Casing / Impeller / Wear rings: Chrome steel (ASTM A217 WC6 / WC9), 316SS, Duplex, or alloy steel (12% Cr) for hydrogen service |
| Seal type | Dual pressurised mechanical seal with API Plan 53B or 54, SiC/SiC faces, with seal support system |
Design & Performance Features
API 610 compliant (OH2, centreline mounted) – designed for continuous high‑temperature, high‑pressure service in hydrogen‑rich environments. Centreline mounting ensures casing thermal expansion does not misalign the shaft. Bearing life >25,000 hours.
High head capability – up to 550 m (5.5 MPa) – essential for overcoming reactor pressure drop and injection into high‑pressure loop.
Hydrogen service materials – chrome steel (WC6/WC9) or 12% Cr alloy offers resistance to hydrogen attack, H₂S corrosion, and temper embrittlement. Optional 316SS or Duplex for more corrosive feedstocks.
Large suction (6”)/discharge (4”) ratio – maintains low NPSH requirements and handles high flow without cavitation.
Back pull‑out design – rotor assembly can be removed without disturbing piping or motor, reducing turnaround time significantly.
Dual pressurised mechanical seal – API Plan 53B (pressurised barrier fluid) or Plan 54 (external pressurised seal), with SiC/SiC faces for abrasive/high‑temperature service. Engineered to contain high‑pressure hydrocarbon and hydrogen safely.
Heavy‑duty bearing housing – forced oil circulation or oil mist lubrication options (API 614), with temperature and vibration monitoring.
High efficiency hydraulic design – “FX” trim optimises the impeller and volute for the specific first‑stage reactor duty, reducing power consumption.
Typical Applications
First‑stage hydrocracker (HCU) charge pump
Hydrotreater (HDS / HDM) reactor feed pump
Catalytic reforming reactor charge pump
Chemical reactor feed (high‑pressure polyethylene, methanol synthesis, etc.)
High‑pressure boiler feed or high‑head process injection
Why Choose 1st Stage Reactor Feed Pump CP 4x6x9FX for Reactor Feed Service?
Reactor feed pumps operate at the extreme limits of pressure, temperature, and reliability. Any failure forces a complete unit shutdown. This CP series pump is built to API 610 for maximum uptime in hydrogen service. The centreline‑mounted casing, chrome steel metallurgy, dual pressurised seals, and high‑efficiency hydraulics make it the ideal choice for first‑stage reactor charge duties. The “FX” hydraulic trim offers tailored performance for your specific flow/head requirement, avoiding oversizing and energy waste.
Contact
For API datasheets, material selection (WC6/WC9 vs 316SS vs Duplex), seal system design, or quotation:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.