ZQ127/25Y TEDA Drill Pipe Power Tong – Common Troubles and Effective Remedies

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The ZQ127/25Y TEDA drill pipe power tong troubleshooting guide covers three common operational issues. Tong dies slip: hard objects in die grooves, worn dies, or unlevel tong body – clean grooves, replace dies, or level tong. Master tong head and backup tong head misalignment: retaining pin not contained by reset knob axle – turn reset knob and reset. Master tong clamps well while backup tong slips: reverse rotation direction of jaw plate frame – exchange positions of the two hoses. Quick remedies restore reliable operation.

Conatct For Details
DetailReview(0)Additional

Even the most robust hydraulic power tongs can encounter operational issues, particularly in demanding well workover environments. The ZQ127/25Y TEDA Drill Pipe Power Tong is designed for reliability, but when problems do arise, a systematic approach to troubleshooting and repair minimizes downtime and maintains safety. This guide covers the three most frequently reported troubles, their root causes, and proven corrective actions.

Trouble 1: Tong Dies Slip

Possible Causes and Remedies:

Die grooves filled with hard objects – Over time, debris, scale, or metallic particles can become packed into the die‑holding grooves, preventing the dies from seating firmly against the pipe. Remedy: Clean the die grooves thoroughly, removing all foreign material and sundries from the groove. Ensure the dies are free to move and fully engage the pipe.

Dies excessively worn – The gripping teeth on the dies become blunt or rounded after extended use, losing their ability to bite into the pipe. Remedy: Replace with new dies of the correct size and specification. Always replace dies in matched sets to maintain even grip pressure.

Tong body not level – If the master tong and backup tong are not perfectly horizontal, the clamping force is unevenly distributed, causing the dies to contact the pipe at an angle. Remedy: Adjust the tong level for both the master tong and backup tong. Use a spirit level to confirm horizontal alignment in both directions. Re‑level the tong at the start of each work shift or whenever the suspension has been adjusted.

Trouble 2: Master Tong Head and Backup Tong Head Not in Alignment with the Opening

Possible Causes and Remedies:

Retaining pin cannot be contained by reset knob axle – The retaining pin is not properly engaged with the reset knob axle, preventing the mechanism from returning to the correct starting position. Remedy: Turn the reset knob and reset the mechanism again. This action allows the retaining pin to be properly captured by the reset knob axle, restoring correct alignment. If the issue persists, inspect the reset knob and axle for wear or damage and replace if necessary.

Trouble 3: Master Tong Clamps Well While Backup Tong Slips

Possible Causes and Remedies:

The turning direction of the jaw plate frame of the backup tong is opposite to the turning direction of the master tong – This occurs when the hydraulic hoses supplying the backup tong are connected in reverse polarity, causing the backup tong jaw mechanism to rotate in the opposite direction to the master tong. Remedy: Exchange the positions of the two hoses connected to the backup tong. Swapping the hoses reverses the flow direction, synchronizing the rotation of the backup tong jaw plate frame with that of the master tong. After swapping, perform a test run with a spare piece of pipe to confirm proper gripping and rotation before resuming production work.

General Troubleshooting Tips

  • Always engage the safety door and ensure the torque control system is set before diagnosing mechanical issues.

  • Keep a log of remedies applied – this helps identify recurring issues that may indicate deeper mechanical wear.

  • When replacing dies or adjusting level, also check the condition of the die holders and guide poles for wear.

  • For hydraulic issues (like hose swapping), ensure the system is depressurized and the tong is suspended securely before disconnecting any lines.

Troubleshooting Quick Reference

ProblemPrimary CausesPrimary Remedies
Tong dies slipDebris in grooves, worn dies, unlevel tongClean grooves, replace dies, level tong
Head misalignmentRetaining pin not contained by reset knob axleTurn reset knob and reset
Backup tong slips (master tong normal)Reverse hose connectionExchange hose positions

Preventive Measures

  • Perform daily pre-use inspections as outlined in the Maintenance and Lubrication section.

  • Replace dies at the first sign of wear – worn dies cause slippage and inconsistent torque.

  • Check tong level regularly – an unlevel tong is a common cause of die slippage.

  • Verify hose connections are correct before operation.

For further technical support, fault diagnosis assistance, or to order replacement components, please contact us via email at info@hyrig.com.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit