Establishing a regular maintenance and lubrication program is essential for the safe, efficient, and long‑term operation of the ZQ127/25Y TEDA Drill Pipe Power Tong. Adhering to the following procedures minimizes wear, prevents unexpected downtime, and ensures that the tong consistently delivers its rated torque and speed performance under demanding well workover conditions.
5.1 Pre-Work Fastener Checks
Before commencing any make‑up or break‑out operation, all fastening screws must be checked for tightness. Loose screws can compromise clamping force and lead to misalignment or component damage. Tighten any loose screws to the specified torque.
5.2 Pre-Work Lubrication
Before each work shift, sufficient lubricating grease must be added to every transmission part. Proper pre‑operation lubrication reduces friction, dissipates heat, and prevents premature wear of critical internal components including gears, bearings, and pivot points.
5.3 Post-Use Cleaning
After each use, the tong body must be inspected to clean up water or oil stains in a timely manner. Accumulated contaminants can cause corrosion, reduce performance, and accelerate wear of moving parts.
5.4 End of Well Operation Cleaning
After each well operation is completed, the tong must be thoroughly cleaned with diesel fuel. Following cleaning, lubricating grease must be added to each transmission part to ensure they remain protected during storage.
5.5 Steam Cleaning Prohibition
Steam cleaning is strictly prohibited for the ZQ127/25Y. High‑pressure steam penetrates seals and bearing housings, forcibly displacing essential lubricating grease and leaving internal components dry. This accelerates wear and can cause rapid failure of gears and bearings. Always use diesel fuel or approved solvent‑based cleaning methods.
5.6 Hydraulic Oil Temperature Management
The hydraulic oil temperature must be maintained below 65°C at all times during operation. Excessive oil temperature degrades the oil's lubricating properties and, more critically, causes premature failure of hydraulic system seals. Overheating leads to seal hardening, cracking, and leakage, which results in pressure drop and reduced tong performance. Monitor the hydraulic oil temperature regularly; if it approaches 65°C, reduce the workload or allow the system to cool before resuming operations.
5.7 Hydraulic Oil Cleanliness
Hydraulic oil must be kept clean to guarantee the normal filtering of the oil filter. Contaminated oil with particles or water will clog the filter element, bypass the filtration system, and cause abrasive wear to precision‑matched components. If the oil appears discoloured, milky, or contains visible debris, it must be replaced immediately. Never top up dirty oil with fresh oil – drain the entire system and refill with clean oil of the correct grade.
5.8 Hydraulic Oil Selection
Selecting the appropriate hydraulic oil grade is crucial for maintaining correct viscosity and flow characteristics across varying environmental conditions. Three oil types are recommended based on ambient temperature:
YC-N46 Low Freezing Hydraulic Oil: Suitable ambient temperature range -20°C to +40°C. Recommended for cold climate operations where low temperatures may affect oil flow.
YB-N46 Wear Resistant Hydraulic Oil: Suitable ambient temperature range -10°C to +40°C. Provides enhanced anti‑wear properties for extended component life in moderate or warm environments.
YA-N46 Ordinary Hydraulic Oil: Suitable ambient temperature range 0°C to +40°C. A cost‑effective option for consistently mild conditions.
Maintenance Checklist
| Frequency | Task |
|---|---|
| Before each use | Check and tighten all fastening screws |
| Before each use | Apply grease to all transmission parts |
| After each use | Clean water and oil stains from tong body |
| After each well operation | Diesel clean and re-grease all transmission parts |
| Continuous | Monitor hydraulic oil temperature (<65°C) |
| As needed | Replace dirty hydraulic oil |
| As needed | Clean oil filter |
| By ambient temperature | Select appropriate hydraulic oil (YC-N46/YB-N46/YA-N46) |
Benefits of Regular Maintenance
Extended equipment service life
Reduced downtime and repair costs
Consistent torque application accuracy
Enhanced operator safety
Lower total cost of ownership
Reliable performance in demanding well workover conditions
For detailed maintenance schedules, lubrication diagrams, or to order replacement parts, please contact us via email at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.