XBSY 32SB180J-4kW Sand Pump | Mud Pump Spraying Pump

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The XBSY 32SB180J-4kW sand pump is a spraying pump matched to mud pumps for flushing and cooling sleeves and pistons. The manual lists 9 m³/h flow, 14 m lift, 48% efficiency, 1750 r/min and 0.93 kW shaft power. The extracted table lists 3 kW motor power while the model designation includes 4kW; confirm at ordering.
Conatct For Details
DetailReview(0)Additional

XBSY 32SB180J-4kW Sand Pump — Spraying Pump for Mud Pump

Overview:

XBSY is the product brand shown in the sand pump manual; HYRIG can supply the XBSY sand pump range and its spare parts. The XBSY 32SB180J-4kW sand pump is a spraying pump especially matched to mud pumps for oil drilling.

Primary Structure

The pump mainly consists of pump body, mechanically sealed pump cover, mechanical seal, impeller and pump base. Mechanical sealing is adopted to ensure operation without leakage. Two drive types are available: motor direct drive and pulley drive.

Installation Requirements

  • Install as near to the pumping source as possible to shorten the suction section.
  • Installation shall be horizontal, firm, reliable and vibration-prevention.
  • For motor direct drive, coupling alignment requires parallel offset ≤ 0.25 mm and angular error ≤ 0.12 mm.
  • For pulley drive, pulley axles shall be parallel with end error ≤ 2 mm; belt aligned and equally tensioned; motor balanced and locked.
  • Inlet pipeline section area must be larger than or equal to the pump section area.
  • Suction pipeline shall not be fitted with a throttle valve; a normally open valve may be used and closed only during inspection/repair.
  • Inlet pipeline must be horizontal and straight, with length at least twice the suction pipeline diameter.
  • Each pipeline must have its own support; the pump must not bear pipeline weight.

Operation

  • Manually turn the pump shaft before startup.
  • Fill the pump body and inlet pipeline with fluid to bleed off air.
  • No-load running time cannot exceed 5 seconds.
  • Start the prime mover and gradually open the gate valve.
  • Stop the machine if noise or abnormal phenomena occur.

Lubrication and Maintenance

  • Bearings shall be lubricated with universal lithium-based grease.
  • Replace the grease every 1500 hours of operation.
  • Inspect impeller, shaft, oil seal and bearings according to the manual.
  • Shaft radial runout shall not exceed 0.05 mm; repair or replace if exceeded.

Specifications:

  • Model: 32SB180J-4kW
  • Flow: 9 m³/h
  • Lift: 14 m
  • Efficiency: 48%
  • Speed: 1750 r/min
  • Shaft power: 0.93 kW
  • Motor power: 3 kW as listed in the extracted technical data table; model designation includes 4kW; confirm at ordering
  • Drive type: Motor direct drive or pulley drive
  • Seal: Mechanical seal
  • Data source: Series Sand Pump (Spraying pump) Installation and Operation Instructions, Technical Data table. The motor power field should be verified against the original PDF before ordering.
  • Applications: According to the manual, the sand pump is especially matched for mud pumps in oil drilling. It flushes and cools the sleeve and pistons during pump operation, and can also be used in other situations for transporting mud.

FAQ:

  • Q1: What is the XBSY 32SB180J-4kW sand pump? A1: It is a spraying pump matched to mud pumps for flushing and cooling sleeves and pistons.
  • Q2: What are the listed flow and lift? A2: 9 m³/h flow and 14 m lift.
  • Q3: What is the motor power? A3: The extracted technical data table lists 3 kW, while the model designation includes 4kW; confirm at ordering.
  • Q4: How often should bearing grease be replaced? A4: Every 1500 hours of operation.

Contact Us:

For XBSY 32SB180J-4kW sand pump selection and spare parts, contact HYRIG: info@hyrig.com

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit