XBSY 32PL / 32PL(B) Sand Pump — Spraying Pump for Mud Pump
Overview:
XBSY is the product brand shown in the sand pump manual; HYRIG can supply the XBSY sand pump range and its spare parts. The XBSY 32PL and 32PL(B) are spraying pumps especially matched to mud pumps for oil drilling.
Primary Structure
The pump mainly consists of pump body, mechanically sealed pump cover, mechanical seal, impeller and pump base. Mechanical sealing is adopted to ensure operation without leakage. Two drive types are available: motor direct drive and pulley drive.
Installation Requirements
- Install as near to the pumping source as possible to shorten the suction section.
- Installation shall be horizontal, firm, reliable and vibration-prevention.
- For motor direct drive, coupling alignment requires parallel offset ≤ 0.25 mm and angular error ≤ 0.12 mm.
- For pulley drive, pulley axles shall be parallel with end error ≤ 2 mm; belt aligned and equally tensioned.
- Inlet pipeline section area must be larger than or equal to the pump section area.
- Suction pipeline shall not be fitted with a throttle valve; a normally open valve may be used.
- Inlet pipeline must be horizontal and straight, with length at least twice the suction pipeline diameter.
- Each pipeline must have its own support; the pump must not bear pipeline weight.
Operation
- Manually turn the pump shaft before startup.
- Fill the pump body and inlet pipeline with fluid to bleed off air.
- No-load running time cannot exceed 5 seconds.
- Start the prime mover and gradually open the gate valve.
- Stop the machine if noise or abnormal phenomena occur.
Lubrication and Maintenance
- Bearings shall be lubricated with universal lithium-based grease.
- Replace the grease every 1500 hours of operation.
- Inspect impeller, shaft, oil seal and bearings according to the manual.
- Shaft radial runout shall not exceed 0.05 mm.
Specifications:
- Flow: 32PL 7.5 m³/h; 32PL(B) 7.5 m³/h
- Lift: 32PL 10 m; 32PL(B) 10 m
- Efficiency: 32PL 48%; 32PL(B) 48%
- Speed: 32PL 1420 r/min; 32PL(B) 1420 r/min
- Shaft power: 32PL 0.55 kW; 32PL(B) 0.65 kW
- Motor power: 32PL Not listed in the technical data table; 32PL(B) Not listed in the technical data table
- Drive type: 32PL Motor direct drive or pulley drive; 32PL(B) Motor direct drive or pulley drive
- Seal: 32PL Mechanical seal; 32PL(B) Mechanical seal
- Data source: Series Sand Pump (Spraying pump) Installation and Operation Instructions, Technical Data table.
- Applications: According to the manual, the sand pump is especially matched for mud pumps in oil drilling. It flushes and cools the sleeve and pistons during pump operation, and can also be used in other situations for transporting mud.
FAQ:
- Q1: What is the difference between XBSY 32PL and 32PL(B)? A1: The manual lists shaft power 0.55 kW for 32PL and 0.65 kW for 32PL(B); flow, lift, efficiency and speed are the same.
- Q2: What are the listed flow and lift? A2: 7.5 m³/h flow and 10 m lift.
- Q3: Is motor power listed? A3: No, motor power is not listed in the technical data table.
- Q4: How often should bearing grease be replaced? A4: Every 1500 hours of operation.
Contact Us:
For XBSY 32PL / 32PL(B) sand pump selection and spare parts, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.