XBSY 40SB180J-3kW Sand Pump | Mud Pump Spraying Pump

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The XBSY 40SB180J-3kW sand pump is a spraying pump matched to mud pumps for flushing and cooling sleeves and pistons. The manual lists 15 m³/h flow, 10 m lift, 53% efficiency, 1420/1750 r/min, 0.78 kW shaft power and 4 kW motor power. It uses a mechanical seal and can be motor direct driven or pulley driven.
Conatct For Details
DetailReview(0)Additional

XBSY 40SB180J-3kW Sand Pump — Spraying Pump for Mud Pump

Overview:

XBSY is the product brand shown in the sand pump manual; HYRIG can supply the XBSY sand pump range and its spare parts. The XBSY 40SB180J-3kW sand pump is a spraying pump especially matched to mud pumps for oil drilling.

Primary Structure

The sand pump mainly consists of pump body, mechanically sealed pump cover, mechanical seal, impeller and pump base. Mechanical sealing is adopted to ensure operation without leakage. The pump has two drive types: motor direct drive and pulley drive.

Installation Requirements

  • Install the pump as near to the pumping source as possible to shorten the suction section and reduce suction loss.
  • Installation shall be horizontal, firm, reliable and vibration-prevention.
  • For motor direct drive, the elastic shaft coupling alignment requires parallel offset no more than 0.25 mm and angular error no more than 0.12 mm.
  • For pulley drive, the two pulley axles shall be parallel with end error no more than 2 mm; the belt must be aligned and equally tensioned; the motor shall be balanced and locked.
  • The inlet pipeline section area must be larger than or equal to the pump section area.
  • The suction pipeline shall not be fitted with a throttle valve; a normally open valve may be used and closed only during inspection/repair.
  • The pipeline at the pump inlet must be horizontal and straight, with a length of at least twice the suction pipeline diameter.
  • Each pipeline must have its own support. The pump must not bear pipeline weight.
  • When operating condition is unclear or unstable, the outlet pipeline must be equipped with a throttle valve to ensure operation at the design point.

Operation

Before startup:

  • Manually turn the pump shaft to ensure smooth operation without grating.
  • Fill the pump body and inlet pipeline with fluid to bleed off air.
  • No-load running time cannot exceed 5 seconds. The pump must run with liquid; otherwise the mechanical seal may be damaged.

Startup and operation:

  • Start the prime mover and gradually open the gate valve to the required position.
  • Stop the machine if noise or other abnormal phenomena occur.

Lubrication and Maintenance

  • Bearings shall be lubricated with universal lithium-based grease.
  • Replace the grease every 1500 hours of operation.
  • During disassembly, remove the pump body, impeller nut and stop washer, then remove the impeller; remove the mechanical seal pump cover and mechanical seal; remove the bearing glands; use a copper stick or wood block to remove the shaft and bearing components without damaging the shaft shoulder.
  • Inspect the impeller for serious cavitation, excessive corrosion, ablation or breakage; replace if necessary.
  • Inspect the shaft: when radial runout exceeds 0.05 mm, oil seal location is seriously abraded, or shaft thread/groove/pedestal is damaged, repair or replace the shaft.
  • Disassembled oil seals must be replaced.
  • Bearings that are excessively worn, too tight/loose, or noisy during operation must be replaced with the same type and dimensions.

Parts and Exploded View

The manual includes a 40SB180J sand pump exploded drawing and bill of materials. Key part numbers include:

ItemDescriptionPart No.Qty
5Impeller40SB180J00051
11Mechanical seal40SB180J00111
12Shaft sleeve40SB180J00121
16Oil seal40SB180J00162
19Bearing40SB180J00192
20Shaft40SB180J00201

The full 28-item main pump parts list and 18-item set drawing parts list are on the 40SB180J parts and exploded view page.

Specifications:

  • Model: 40SB180J-3kW
  • Flow: 15 m³/h
  • Lift: 10 m
  • Efficiency: 53%
  • Speed: 1420/1750 r/min
  • Shaft power: 0.78 kW
  • Motor power: 4 kW (as listed in the technical data table; model designation includes 3kW; confirm at ordering)
  • Drive type: Motor direct drive or pulley drive
  • Seal: Mechanical seal
  • Data source: Series Sand Pump (Spraying pump) Installation and Operation Instructions, Technical Data table.
  • Applications: According to the manual, the sand pump (spraying pump) is especially matched for mud pumps in oil drilling. It flushes and cools the sleeve and pistons during pump operation, and can also be used in other situations for transporting mud.

FAQ:

  • Q1: What is the XBSY 40SB180J-3kW sand pump? A1: It is a spraying pump matched to mud pumps for flushing and cooling sleeves and pistons, and for transporting mud in other situations.
  • Q2: What are the listed flow and lift? A2: The manual lists 15 m³/h flow and 10 m lift.
  • Q3: What is the no-load running limit? A3: No-load running time cannot exceed 5 seconds; the pump must run with liquid.
  • Q4: How often should bearing grease be replaced? A4: Replace universal lithium-based grease every 1500 hours of operation.
  • Q5: What drive types are available? A5: Motor direct drive and pulley drive.

Contact Us:

For XBSY 40SB180J-3kW sand pump selection, installation information or spare parts, contact HYRIG: info@hyrig.com

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit