10" Desander Cone | Derrick 6066-51 Compatible Replacement

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 10-inch desander cone is a drop-in compatible replacement for the Derrick 6066-51 assembly, rated at 500 GPM per cone at 75 ft of head. It is used in drilling fluid solids control to remove sand-sized particles in the 40–100 μm range. The polyurethane cone body and Victaulic coupling match the original installation dimensions, so existing pipework and manifold brackets require no alteration. HYRIG supplies independent, compatible replacement products for Derrick desander installations; we are not affiliated with, authorized by, or endorsed by Derrick Corporation.
Conatct For Details
DetailReview(0)Additional

Key Facts



Cone Size10 inches
Replacement Part No.Derrick 6066-51
Flow Capacity500 GPM at 75 ft head (≈ 113 m³/h)
Separation Size40–100 μm
Cone MaterialPolyurethane (ceramic liner optional)
Operating Pressure0.06–0.3 MPa
Compatible HostDerrick desander units, mud cleaners (FLC series)
Replacement CompatibilityDerrick 6066-51; verify apex and coupling before order

Key Specifications (10" Desander Cone 6066-51 Compatible)

ParameterValue
Cone diameter10 in (254 mm)
Inlet / outlet connectionMatches Derrick 6066-51 flange configuration
Flow capacity per cone500 GPM at 75 ft head
Separation range40–100 μm
Cone body materialPolyurethane, optional ceramic lower-section liner
Apex size1.250 in standard; variable apex available
Operating pressure0.06–0.3 MPa
Mud temperature range0–100 °C
Coupling type5" Victaulic #75

Data source: Technical data table.

Dimensions

DimensionValue
Overall assembly heightMatches 6066-51 outline
Upper section ODMatches 6066-52 upper section
Mounting interfaceDrop-in replacement; existing brackets and pipework require no alteration
Weight (approx.)18–22 kg depending on liner option

Structure / Working Principle

Drilling mud enters the cone tangentially under pressure. Centrifugal force drives denser solids toward the cone wall and down to the apex as underflow, while clarified fluid exits through the vortex finder as overflow. The polyurethane body absorbs continuous abrasive wear, keeping the cut point stable between replacement intervals. Separate ball valves on each cone inlet allow individual shut-off during operation, so you can isolate a worn cone without stopping the whole manifold. The 6066-57 apex and 6066-58 holder are replaceable without discarding the full cone body, which reduces wear-part cost during scheduled maintenance.

Cross-Reference & Replacement

Looking for a compatible replacement for a Derrick 6066-51? Here's what to check:

  1. Inlet/outlet flange dimensions — confirm against your existing 6066-51 cone drawing; the replacement matches the standard 10" Derrick desander interface.
  2. Apex size — standard 1.250 in vs. variable apex; match your current underflow density target.
  3. Coupling type — 5" Victaulic #75. Verify the clamp groove on your manifold before ordering.
  4. Liner option — polyurethane standard; specify ceramic lower-section liner if your mud contains high-abrasive sand.

Not interchangeable with: 4" desilter cones or 10" cones from non-Derrick manifold patterns without dimension verification.

Compatible Host Models

This 10" desander cone is intended for use in:

  • Derrick FLC 503 / FLC 504 mud cleaner desander sections
  • Derrick standalone desander units with one to three 10" cone manifolds
  • Derrick-style mud cleaner systems where 6066-51 cone assemblies are specified

For the full Derrick-compatible hydrocyclone range, see Derrick-compatible hydrocyclone cones — covering both 10" desander and 4" desilter sizes.

Applications

  • Weighted mud systems — removes sand-sized solids ahead of the desilter stage while limiting barite loss.
  • Mud cleaner desander section — replaces worn 10" cones on FLC 503/504-style units during scheduled maintenance shutdowns.
  • High-flow drilling operations — each cone handles 500 GPM at 75 ft head; three-cone manifolds are rated up to 1,500 GPM.
  • Year-end shutdown planning — keep spare cone assemblies on hand to avoid non-productive time when a cone’s cut point drifts.

Selection Support

Not sure whether your existing manifold takes a standard 1.250" apex or a variable apex? Send us your current cone drawing or the part number stamped on the cone body, and our team will confirm the matching replacement configuration before you order.

Spare Parts

HYRIG provides replacement parts for the 10" desander cone assembly. Whether you need a complete cone assembly or specific wear components, the following part-level items can be quoted separately:

Part NameReference Part No.Notes
Upper section6066-52Cone body upper
Upper band6066-53Clamp band
Middle section6066-54Cone body middle
Lower band6066-55Clamp band
Lower section6066-56Cone body lower
Apex 1.2506066-57Standard apex
Apex holder6066-58Apex retention
5" Victaulic couplingMC-5-75Manifold connection

Qty as per parts list; verify against original drawing. For individual wear parts and inspection guidelines, view our Derrick hydrocyclone wear parts index.

Frequently Asked Questions

Q1: Is this an original Derrick product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by Derrick.

Q2: How do I confirm this cone replaces my 6066-51?
A: Match the 10" cone diameter, 5" Victaulic coupling, and 1.250" standard apex. Send us a photo of your existing cone nameplate if the part number is worn.

Q3: What is the typical lead time for a replacement 10" desander cone?
A: Standard polyurethane cones ship in 2–3 weeks; ceramic-lined versions take 4–5 weeks. Plan around year-end shutdown windows to avoid downtime.

Q4: Can I order the apex separately without the full cone assembly?
A: Yes. The 6066-57 apex and MC-5-75 coupling are available as separate wear components. Confirm the apex size before ordering.

Q5: What should I inspect if the cone cut point starts drifting?
A: Check the apex opening for erosion and the lower cone section for grooving. A worn apex is the most common cause of coarse underflow.

Contact

For 10" desander cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing cone part number or nameplate photo
  • Required quantity
  • Apex size (1.250" standard or variable)
  • Destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit