4" Desilter Cone | Derrick 10523-12 Compatible Replacement

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 4-inch desilter cone is a drop-in compatible replacement for the Derrick 10523-12 assembly, processing 80 GPM per cone with a 15–45 μm cut point. It is used in desilter and mud cleaner manifolds to remove fine silt and sand from drilling fluid after the shaker and desander stages. The polyurethane cone body and thread-on tip match the original installation dimensions, so existing pipework and manifold brackets require no alteration. HYRIG supplies independent, compatible replacement products for Derrick desilter installations; we are not affiliated with, authorized by, or endorsed by Derrick Corporation.
Conatct For Details
DetailReview(0)Additional

Key Facts



Cone Size4 inches
Replacement Part No.Derrick 10523-12
Flow Capacity80 GPM per cone
Separation Range15–45 μm
Cone MaterialPolyurethane (ceramic liner optional)
Compatible HostDerrick FLC 503 / 504 desilter sections; round desilter manifolds
Replacement CompatibilityDerrick 10523-12; verify apex and tip configuration before order

Key Specifications (4" Desilter Cone 10523-12 Compatible)

ParameterValue
Cone diameter4 in (102 mm)
Feed inlet / overflow outletMatches Derrick 10523-12 manifold interface
Flow capacity per cone80 GPM
Separation range15–45 μm
Cone body materialPolyurethane; ceramic lower-section liner optional
Underflow tipThread-on cone tip (10523-01 equivalent), drop-in apex compatible
Operating pressureVerify against your desilter manifold pressure; typical desilter feed is below 50 PSI
Coupling type2" Victaulic snap coupling and ball valve per cone

Data source: Technical data table.

Dimensions

DimensionValue
Overall cone heightMatches 10523-12 assembly height
Cone body OD4 in (102 mm) nominal
Manifold interface2" Victaulic snap coupling; existing round desilter manifold accepts the replacement without bracket modification
Weight (approx.)3–5 kg depending on tip/apex configuration

Structure / Working Principle

Drilling mud enters the 4" cone tangentially through the 2" Victaulic feed inlet. Centrifugal force pushes silt-sized solids to the cone wall and down through the thread-on tip as underflow, while clarified fluid exits upward through the vortex finder. Each cone has a separate ball valve on the feed side, so you can shut off an individual cone for inspection or replacement without interrupting the other cones on the manifold. The thread-on tip allows tip replacement without replacing the entire cone body—a wear-management advantage when the lower cone section is still within tolerance.

Cross-Reference & Replacement

Looking for a compatible replacement for a Derrick 10523-12 desilter cone? Check these 4 points before ordering:

  1. Manifold coupling — 2" Victaulic snap coupling. Confirm your round desilter manifold uses the same groove profile; most FLC 503/504 configurations do, but older manifolds may use a different clamp style.
  2. Tip and apex configuration — standard thread-on tip (10523-01 equivalent) vs. drop-in apex. Match your current underflow setup; if you run a variable apex, confirm the holder is compatible.
  3. Ball valve — each cone should have its own 2" Victaulic ball valve on the feed side. If your existing valve is seized or missing, order the valve with the cone to avoid a second shutdown.
  4. Manifold orientation — round desilter manifolds accept cones in a radial pattern. Confirm the replacement cone’s inlet orientation matches your manifold’s feed direction before installation.

Not interchangeable with: 10" desander cones, or 4" cones designed for non-Victaulic flange manifolds, without verifying coupling and inlet dimensions first. If your manifold uses a flanged rather than grooved connection, contact HYRIG with the manifold drawing before ordering.

Compatible Host Models

This 4" desilter cone is intended for Derrick desilter and mud cleaner configurations, including:

  • Derrick FLC 503 and FLC 504 mud cleaner desilter sections (round manifold, up to twenty 4" cones)
  • Derrick standalone desilter units with 2" Victaulic feed and overflow connections
  • Derrick-style mud cleaners where 10523-12 cones are specified

For the full Derrick-compatible hydrocyclone range, see Derrick-compatible hydrocyclone cones — covering both 10" desander and 4" desilter sizes. For FLC 503/504 configurations that include a desander stage, see the 10" desander cone 6066-51 compatible replacement.

Applications

  • Desilter stage on FLC 503/504 mud cleaners — removes silt-sized solids in the 15–45 μm range after the shaker and desander stages, protecting the centrifuge from fine-solids overload.
  • Fine-solids control in weighted mud systems — the 4" cone’s cut point helps maintain low-speed rheology without excessive weighting-agent loss when the underflow is routed correctly.
  • HDD and CBM compact mud systems — 80 GPM per cone suits multi-cone manifolds on smaller-footprint rigs where a full desander stage is not installed.
  • Scheduled cone replacement during manifold maintenance — the thread-on tip allows tip-only replacement when the body is still serviceable, reducing parts cost during planned shutdowns.

Selection Support

Not sure whether your existing cone uses a thread-on tip or a drop-in apex, or whether your manifold’s Victaulic groove matches the standard 2" profile? Send us a photo of the cone nameplate and the manifold connection, and we will confirm the matching tip and coupling configuration before you order.

Spare Parts

HYRIG provides replacement wear components for the 4" desilter cone. Whether you need a complete cone assembly or specific wear parts, the following part-level items can be quoted separately:

Part NameReference Part No.Notes
4" urethane cone assembly10523-12Complete cone
Hydrocyclone body10523-00Cone body only
Thread-on cone tip10523-01Standard tip
Drop-in apex10523-02Alternative apex style
Triangular nut10523-04Apex retention
2" Victaulic snap couplingVIC-2-78Manifold connection
2" Victaulic ball valveG0002077Feed-side isolation
180° urethane elbow6431-00Overflow routing

Qty as per parts list; verify against original drawing. For individual wear parts and inspection guidelines, view our Derrick hydrocyclone wear parts index.

Frequently Asked Questions

Q1: Is this an original Derrick product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by Derrick.

Q2: How do I confirm this 4" cone replaces my 10523-12?
A: Match the 4" cone diameter, 2" Victaulic coupling, and thread-on tip configuration. Send a nameplate photo if the part number is worn.

Q3: What is the typical lead time for a 4" desilter cone?
A: Standard polyurethane cones ship in 2–3 weeks; orders placed before year-end shutdown windows are scheduled to avoid rig downtime.

Q4: Can I order the thread-on tip separately without the full cone?
A: Yes. The 10523-01 tip and 10523-02 drop-in apex are available as separate wear components. Confirm your tip style before ordering.

Q5: What should I check if the cone starts losing cut point?
A: Inspect the thread-on tip for erosion and the lower cone section for grooving. A worn tip is the most common cause of coarse underflow on 4" desilters.

Contact

For 4" desilter cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing cone part number or nameplate photo
  • Tip style (thread-on vs. drop-in apex)
  • Required quantity
  • Destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit