2" 7500psi Demco HP Mud Valve Dimensions & Installation Guide | HYRIG

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Comprehensive dimensions and installation procedure for 2" 7500psi Demco HP mud valve. BW height 410mm, flanged 410mm height and 305mm width. RTJ flange 8‑7/8" bolts, R‑24 ring. High‑pressure welding prep, orientation, torque, and hydrostatic testing.

Conatct For Details
DetailReview(0)Additional

Overview
Correct installation of the HYRIG 2" 7500psi Demco high‑pressure mud valve is critical to ensuring safe, leak‑free operation at extreme pressures. This guide provides all necessary dimensional data and a step‑by‑step installation procedure in full compliance with API 6A high‑pressure class standards.

Valve Dimensions by Connection Type

ConnectionHeight (mm)Width (mm)
Butt-Weld (BW)410240
RTJ Flanged410305
Hammer Union410255

RTJ Flange Detailed Data

  • Flange O.D.: 216 mm

  • Bolt Quantity/Size: 8 bolts, 7/8" diameter

  • RTJ Ring: R-24

  • Bolt Circle: Standard API 6A high‑pressure dimensions

Butt‑Weld End Preparation

  • Schedule: XXH (Extra Extra Heavy)

  • Material: 4130 Alloy Steel compatible

  • Pre‑heat and post‑weld heat treatment (PWHT) required per API 6A

  • Prior to welding, the seat and bonnet seal must be removed from the valve body

Step‑by‑Step Installation Procedure

Step 1: Pre‑Installation Checks

  • Verify the valve size, pressure rating (7,500 PSI), and connection type match your piping.

  • Inspect all sealing surfaces for transit damage.

  • Ensure the valve is in the fully closed position before installation.

Step 2: Orientation & Clearance

  • Install with the flow arrow pointing downstream.

  • For rising stem valves, provide adequate vertical clearance for full stem extension.

  • Ensure the heavy‑duty handwheel has clearance for full rotation.

Step 3: Connection‑Specific Mounting

  • Butt‑Weld (BW) :

    • Remove seat and bonnet seals before welding.

    • Use XXH schedule pipe with 4130 compatible material.

    • Apply pre‑heat and perform post‑weld heat treatment (PWHT) per API 6A.

    • Allow cooling before reinstalling seals.

  • RTJ Flanged :

    • Install RTJ ring (R‑24) in the groove.

    • Align flange bolt holes.

    • Install bolts (8 bolts, 7/8") and tighten in star pattern.

    • Torque to API 6A high‑pressure recommended values.

  • Hammer Union :

    • Align union halves.

    • Install HP O‑ring seal.

    • Tighten union nut with hammer wrench to API recommended torque.

Step 4: Post‑Installation Testing

  • Perform hydrostatic test per API 6A requirements (test pressure: 11,250 PSI).

  • Check all connections for leaks.

  • Cycle valve fully open and closed to verify smooth operation.

Step 5: Lubrication

  • Apply high‑pressure compatible grease through grease fitting (STD-HP01).

  • Use grease suitable for high‑pressure and high‑temperature service.

Critical Installation Notes

  • Do not use any 5,000 PSI rated components or seals in this 7,500 PSI valve.

  • For sour service (H₂S), ensure all materials are NACE MR‑01‑75 compliant.

  • Use only high‑pressure rated fasteners (B7/L7).

For detailed torque charts or installation troubleshooting, contact info@hyrig.com.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit