This API 610 centrifugal pump series is engineered to handle the full range of refinery and petrochemical process media – from wet crude oil and corrosive inhibitors to high-temperature liquid sulfur, sour water, caustic, amines, and light hydrocarbons. Each pump model is specifically selected or hydraulically trimmed for its intended medium, while fully complying with API 610 8th / 11th / 12th edition (ISO 13709) design standards.
The series includes OH2 (centerline mounted overhung), VS4 (vertical suspended sump), and BB3 (axially split multistage) configurations, ensuring the right hydraulic and mechanical fit for every service. All pumps are designed for continuous 24/7 operation, minimum 3-year uninterrupted run, and a 20-year design life.
| Pump Model | Medium |
|---|---|
| 80AY60 | Wet crude oil |
| TR32-200 | Corrosion inhibitor |
| 100AYⅡ 120A | Hydrogenated diesel |
| 80AYⅢ100×2 | Jet fuel / aviation kerosene fraction |
| HL40-315 | Liquid sulfur |
| HA100-315 | Sour water |
| HA80-400 | Petroleum, sulfides 0.56-1.2 |
| HA40-200 | Caustic / alkali |
| HL25-200 | Liquid sulfur |
| HY32-200 | MDEA solution |
| HLD50-30×2 | Liquid sulfur |
| 80AYP100×2 | Stabilised gasoline |
| HDH6-35×6 | Condensate oil |
| DL6-15×11 | Raw stabilised light hydrocarbon |
| HGPH100-315 | Purified oil |
| HGPN81-160 | Hot water |
| HY50-40×2 | Oil-water mixture |
| HLB32-200 | Crude oil |
| HE50-315 | Fresh water |
| HYB40-250 | Amine solution |
| HLF50-25-146 | (Medium not specified) |
| HA25-250 | (Medium not specified) |
Hydraulic range: Flows from 5 to 500 m³/h, heads from 30 to 250 m (customised per duty)
Temperature range: –45°C to +420°C, depending on materials and medium
Pressure rating: Up to 6.4 MPa (64 bar) for OH2; higher for BB3 configurations
NPSHr: Optimised impeller design, inducer available for low NPSHa conditions
| Medium | Recommended Material (API 610 Table H) | Remarks |
|---|---|---|
| Wet crude / crude oil | Carbon steel (Class II) or 316L SS | Upgrade to duplex if chlorides >500 ppm |
| Corrosion inhibitor | 316L SS (S-8) | Good general corrosion resistance |
| Hydrogenated diesel / jet fuel | Carbon steel or 304 SS | Clean hydrocarbon service |
| Liquid sulfur | 316L SS with hardened wear rings | Temperature up to 150°C; avoid rapid solidification |
| Sour water (H₂S) | 316L SS (S-8) or duplex | NACE MR0175 compliance required |
| Caustic (alkali) | 304/316 SS | Avoid stress corrosion cracking above 50°C |
| MDEA / amine solution | 316L SS (S-8) | Dual seals mandatory for rich amine |
| Stabilised gasoline / light hydrocarbons | Carbon steel | Standard refinery service |
| Condensate / purified oil | Carbon steel or 304 SS | Clean service |
| Hot water | Carbon steel or 304 SS | Above 100°C, use balanced seals |
| Oil-water mixture | 316L SS (S-8) | Similar to wet crude |
All pumps are fitted with API 682 (4th edition) cartridge mechanical seals. Seal type and flush plan are selected based on medium characteristics:
| Medium | Recommended Seal Configuration | Flush Plan |
|---|---|---|
| Wet crude / oil-water | Dual pressurized seal (Type A) | Plan 53B |
| Sour water (H₂S) | Dual pressurized seal (Type B) | Plan 53B or 52 |
| Caustic / MDEA / amine | Dual seal (Type A) | Plan 53A / 53B |
| Liquid sulfur | Single seal with quench (Type A) | Plan 62 (steam quench) |
| Diesel / jet fuel / gasoline | Single seal (Type A) | Plan 11 / 21 |
| Hot water | Single balanced seal (Type B) | Plan 23 (cooled) |
| Fresh water / clean service | Single seal (Type A) | Plan 11 |
Sour water contains dissolved H₂S and ammonia, highly corrosive and toxic. Pumps in this service must meet NACE MR0175 / ISO 15156 material requirements. Dual mechanical seals with Plan 53B are mandatory. 316L stainless steel wetted parts are standard.
Rich amine (loaded with H₂S/CO₂) is corrosive and releases toxic gas. Use 316L SS (S-8) or higher. Sealing must be API 682 dual pressurized (Plan 53B). For lean amine, single seals with Plan 11 may be acceptable but dual seals are strongly preferred.
Liquid sulfur is typically handled at 130–150°C. Cooling or solidification on shutdown is a major risk. Pumps require steam jacketed casings and steam-quenched seals (Plan 62). Material: 316L SS with hard face wear rings.
Concentrated caustic can cause stress corrosion cracking in stainless steels above 50°C. For ambient temperature dilute caustic, 304/316 SS is acceptable. For higher concentrations or temperatures, use nickel-based alloys or controlled caustic service guidelines.
Clean hydrocarbon services are the most straightforward. Carbon steel casings with single mechanical seals (Plan 11 or 21) are sufficient. Ensure API 610 bearing housing and centreline mounting for thermal growth.
Full compliance with API 610 (8th/11th/12th) – verified design records
Complete material traceability and NACE options
API 682 sealing systems – customised for each medium’s hazard level
Long bearing life (L10 ≥25,000 hours) and modular construction
Proven field performance in refineries, gas plants, and oilfields
Direct interchangeability with legacy Y-type and other API pumps
For a detailed selection of the right API 610 centrifugal pump for your specific medium – including hydraulic calculation, material recommendation, and sealing plan – please contact us.
Email: info@hyrig.com
Our engineers support refinery and petrochemical projects worldwide with reliable, API-compliant pumping solutions for every medium listed above.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.