API 610 Wet Crude Oil Transfer Pump – Model 80AY60 (Two-Stage Single-Suction OH2)

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 wet crude oil transfer pump Model 80AY60. Two-stage single-suction OH2 centerline design. Capacity 50m³/h, total head 120m, temperature -45°C to +420°C. Ideal for oil-water mixture (≤80% water content, low sand). API 682 mechanical seals, balance disc+balance drum for axial thrust. Retrofits legacy Y-type pumps. Explosion-proof motor ready.

Conatct For Details
DetailReview(0)Additional

Product Overview

The Model 80AY60 is a two-stage, single-suction, overhung centrifugal pump specifically engineered for wet crude oil transfer in oilfields, refineries, and central processing stations. The pump is fully developed following API 610 8th / 11th / 12th edition design criteria and features a centerline mounting configuration (OH2 type) – ensuring thermal stability and mechanical integrity under severe process conditions.

This pump is designed to handle oil-water mixtures (wet crude) with up to 80% water content and very low sand content (<0.1%). It reliably serves applications from –45°C up to +420°C, making it a direct energy‑efficient upgrade for traditional Y‑type crude oil pumps in petrochemical service.


Model Number Decoding – 80AY60

CodeMeaning
80Inlet diameter DN80 (mm)
AFirst impeller trim – allows fine adjustment of flow/head for specific duty
YPetrochemical centrifugal oil pump series code
60Nominal single‑stage head: 60 meters (total head ~120 m with two stages)

Key Performance Parameters (50Hz, 2950 rpm, fresh water basis)

ParameterValueCorrection for wet crude duty
Rated flow Q50 m³/hDesign range 30–60 m³/h; slight reduction with higher viscosity
Rated head H60 m × 2 stages = 120 mHead decreases 5%–10% as water content rises (density effect)
Efficiency η62%Approx. 58%–60% on wet crude, varies with water cut
Shaft power13.19 kWIncreases with higher fluid density (water cut ↑); verify motor sizing
NPSHr3.2 mEnsure NPSHa ≥ NPSHr + 1 m for wet crude (vapor pressure effect)
Speed2950 r/min
Temperature range–45°C to +420°CFully compatible with ambient to ≤120°C wet crude service
Standard motor power18.5 kWExplosion‑proof YB160L‑2, suitable for oilfield hazardous area

Construction & API 610 Compliance

Pump configuration:
Horizontal, radially split, centerline mounted (API 610 OH2). Two‑stage single‑suction overhung design – impellers arranged in series. Compact, no intermediate bearing. Designed for continuous 24/7 operation in refinery and oilfield environments.

Wetted parts materials (recommended for wet crude):

ComponentStandard materialUpgrade for corrosive service
Casing / ImpellerCarbon steel (Class II, –45~400°C)304/316 SS, Duplex (for Cl⁻ or H₂S)
Shaft45# steel / 2Cr13316 SS for severe corrosion
Mechanical sealCartridge type (API 610/API 682)Bellows seal for >150°C service
BearingsRolling bearings (oil bath)Heavy‑duty wear‑resistant bearings for trace sand ≤0.1%

API 610 compliance highlights for wet crude service:

  • Axial thrust balance: Combination of balance disc + balance drum – no friction at start/stop. Ideal for frequent start‑stop and variable flow conditions common in wet crude systems.

  • Sealing system: API 682 cartridge mechanical seals with leak‑containment design. Optional Plan 32 external flush or Plan 52 seal pot for oil‑water emulsions.

  • Reliability: Bearing L10 life ≥25,000 hours (API 610 mandatory). Modular construction for easy maintenance.


Wet Crude Service – Application Suitability

Perfectly suited for:

  • Oilfield gathering systems: Wet crude with water content ≤80%, sand ≤0.1%, temperature ≤120°C

  • Refinery / central processing stations: Crude before dehydration, oil‑water mixture transfer, tank farm circulation

  • Media conditions: Viscosity 5–50 mm²/s, no hard solid particles

Critical engineering considerations for wet crude:

  • Water cut effect: Each 10% increase in water content raises fluid density ~5–8% → shaft power increases. Verify motor power to prevent overload. Actual head must be corrected: H_actual = H_water × (ρ_water / ρ_actual).

  • Corrosion protection: If wet crude contains chlorides (≥500 ppm) or sulfides, upgrade to 316 SS or duplex stainless steel to avoid pitting and stress corrosion cracking.

  • Cavitation control: Water has higher vapor pressure than crude. Wet crude is more prone to cavitation. Ensure NPSHa ≥ NPSHr + 1 m. Consider a booster pump for low suction pressure.

  • Wear management: Sand content must be kept ≤0.1%. For higher sand, install a pre‑filter or specify hardened/cermet coated impellers.


API 610 Design Advantages for Wet Crude Transfer

FeatureBenefit for wet crude service
Robust centerline mountingHandles thermal expansion from hot crude; maintains alignment
Balance disc + drumReliable during frequent start‑stop and two‑phase (oil/water) slugs
API 682 seal compatibilityPrevents leaks from unstable emulsions; field‑proven Plan 32/52 options
Heavy‑duty bearings (L10 ≥25,000 hrs)Reduces unplanned downtime by >30% compared to non‑API pumps
Interchangeable with legacy Y‑typeDirect retrofit – no foundation or piping changes; lower CAPEX

Troubleshooting – Wet Crude Specific

ProblemRoot cause (wet crude service)Corrective action
Motor overloadHigh water content → increased fluid densityReduce flow; upgrade motor; optimize operating point
Mechanical seal leakageOil‑water emulsion → poor lubrication, seal face wearInstall API 682 seal with Plan 32 external flush
Pump vibrationUnstable water cut; impeller imbalanceStabilize feed; re‑balance impeller
Head lossDensity increase; over‑trimmed impellerRe‑size impeller for actual wet crude SG; verify speed
Corrosion/erosionChlorides, sulfides, or sandUpgrade to 316/duplex; install sand filter

Why Choose Model 80AY60 for Your Wet Crude Application?

  • API 610 compliance (8th/11th/12th) – field‑proven reliability, designed for 20‑year life

  • Optimized for oil‑water mixtures – up to 80% water cut without derating

  • High thermal capability – from –45°C to +420°C, suitable for hot crude or cold start‑up

  • Energy efficient – replaces inefficient Y‑type pumps; direct retrofit reduces OPEX

  • Safety ready – explosion‑proof motor + leak‑tight seals, meeting HSE requirements


Get a Quote or Engineering Support

For a detailed selection, hydraulic correction for your specific water cut and crude properties, or a complete API 610 pump package, please contact us.

Email: info@hyrig.com

Our engineers support oilfield and refinery projects worldwide – from onshore gathering to refinery crude units.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit