The cryogenic in-tank pump is a vertically suspended, submersible centrifugal pump designed for installation inside storage tanks handling liquefied gases – LNG (liquefied natural gas), LOX (liquid oxygen), LN₂ (liquid nitrogen), LAr (liquid argon), and LH₂ (liquid hydrogen). The pump fully complies with API 610 11th/12th edition (VS6 type) and ISO 24490 cryogenic vessel pump standards, ensuring the highest safety and reliability for critical cryogenic services.
By integrating the pump and motor inside the tank without mechanical seals or couplings, the design eliminates all dynamic leak paths, minimizes heat in-leak, and achieves near-zero Net Positive Suction Head Required (NPSHr). This allows maximum usable tank capacity and 100% leak-free operation.
| Feature | Specification |
|---|---|
| API 610 Type | VS6 (vertical double-casing can pump) |
| Mounting | Submerged inside tank or suction vessel |
| Sealing | No shaft seal – motor and pump fully immersed in cryogenic liquid |
| Stages | Single-stage or multi-stage diffuser-type |
| Motor Cooling | Direct cooling by cryogenic fluid |
| Parameter | Range |
|---|---|
| Flow rate | Up to 20,000 m³/h (88,000 GPM) |
| Head | Up to 2,000 m (6,560 ft) |
| Discharge pressure | Up to 220 bar (3,190 psig) |
| Operating temperature | –200°C (–328°F) to +60°C |
| Speed | 1,450 – 3,600 rpm |
Casings & column: 316/316L stainless steel (S-8) or 9% nickel steel for LNG down to –196°C
Impellers & diffusers: 316L / austenitic stainless steel (A-7/A-8)
Bearings: Cryogenically compatible, life >16,000 hours
Thrust bearings: Optional tilting-pad for high-head applications
All materials are NACE MR0175 / ISO 15156 compliant upon request for sour cryogenic gas services.
Zero leakage, seal-less design – No mechanical seals, no gland packing, no seal flush plans. The submerged motor eliminates all rotating shaft penetrations through the tank wall. Only stationary electrical connections exit the tank, providing absolute fugitive emission control.
Ultra-low NPSHr – Integrated inducer at the suction inlet reduces NPSHr to as low as 0.37 m, enabling lower minimum liquid levels and higher usable storage capacity.
High efficiency – Optimized hydraulic design achieves efficiencies up to 80.2% at rated point (verified by independent testing), significantly reducing operating costs.
Retractable option – For large LNG storage tanks, retractable in-tank pump columns allow pump removal and maintenance without tank decommissioning or liquid removal.
Reliable submerged motor – Stator and rotor are cooled directly by the cryogenic liquid. Coil temperature rise is limited to approximately 12°C under full load, ensuring long insulation life.
| Industry | Application |
|---|---|
| LNG receiving terminals | Unloading, transfer, and send-out to regasification |
| FSRU / FPSO | Floating regasification and production storage |
| LNG bunkering stations | Fuel transfer to marine vessels and trucks |
| LNG carriers | Cargo handling pumps |
| Air separation plants | LOX, LN₂, LAr transfer and loading |
| Peak shaving / satellite stations | Reliable send-out during peak demand |
| Hydrogen liquefaction plants | LH₂ transfer (special materials and design) |
Independent benchmark at LNG terminal duty conditions (Q = 319 m³/h, H = 275 m):
| Supplier | Efficiency | NPSHr |
|---|---|---|
| Our API 610 VS6 pump | 80.2% | 0.37 m |
| Competitor A (NIKKISO) | 69.5% | 0.50 m |
| Competitor B (EBARA) | 68.1% | 0.58 m |
Higher efficiency directly reduces annual power cost. For a typical 9-pump LNG terminal, the efficiency advantage can save over RMB 2 million per year in electricity.
API 610 11th/12th edition (ISO 13709) – Full compliance for VS6 vertical pumps
ISO 24490:2025 – Cryogenic vessels – Centrifugal pumps for cryogenic service
API 682 4th edition – For any auxiliary seal systems (if applicable)
NACE MR0175 / ISO 15156 – For sour cryogenic service (H₂S-containing)
ATEX / IECEx – For explosive atmospheres (LNG vapor zones)
100% hydrostatic testing – Each pump casing tested at 1.5x design pressure
Performance testing – Using LN₂ or LNG as test fluid per ISO 24490
Fixed in-tank pump – Permanently installed, lowest cost, suitable for medium and large tanks.
Retractable in-tank pump – Removable column assembly via top flange; pump can be withdrawn through a vacuum-insulated tube without tank shutdown. Ideal for large LNG storage tanks (60,000 m³ and above).
Submerged motor in suction vessel – Pump installed inside a separate suction pot or vessel, suitable for smaller satellite stations and bunkering skids.
Bearing life >16,000 hours continuous operation
Motor insulation resistance easily monitored
Retractable design allows full pump overhaul without draining or purging the tank
Global spare parts and field service support available
For detailed sizing, material selection, hydraulic analysis, or a complete API 610 cryogenic in-tank pump proposal, please contact our engineering team.
Email: info@hyrig.com
Our engineers are ready to support your LNG, LOX, LN₂, or LAr pumping requirements – from small satellite stations to large-scale LNG export terminals.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.