The API 610 OH2 (Overhung Type 2) crude oil pump is the industry’s most widely used heavy‑duty centrifugal pump for crude oil services in refineries, oilfields, and pipeline terminals. Its centerline‑mounted casing (distinguishing it from foot‑mounted OH1) provides superior resistance to thermal expansion, vibration, and nozzle loads – essential for continuous, high‑temperature, high‑pressure crude oil applications.
Structural Definition – OH2 per API 610
Horizontal, single‑stage, single‑suction, end suction (axial inlet, radial/top discharge).
Centerline‑mounted – casing supported from the centreline flange, not from the bottom.
Overhung impeller – impeller mounted at the end of the shaft, outside the bearing housing.
Radially split volute casing.
Closed impeller, heavy‑duty independent bearing housing.
Back pull‑out design – rotor, seal, and bearing housing can be removed without disturbing piping or motor.
Key Specifications for Crude Oil Duty
Compliance: API 610 12th Edition, ISO 13709, API 682 (sealing), NACE MR0175 (H₂S resistant), ATEX (explosive atmospheres).
Flow: 50 – 3000 m³/h (typical optimum 100 – 2000 m³/h).
Head: 30 – 380 m (single‑stage, typical ≤250 m).
Design pressure: Up to 11 MPa (110 bar) – commonly 5–10 MPa (Class 300/600).
Temperature: –40°C to +450°C (typical crude oil 20–200°C; waxy/heavy crude requires steam/electric tracing to 60–150°C).
Speed: 1480 or 2980 rpm (1480 rpm preferred for lower vibration, longer seal/bearing life).
NPSH: Requires adequate NPSHa (≥ NPSHr + 0.5–1.0 m); inducer optional for low NPSH crude.
Materials for Crude Oil (Sour, Salty, Waxy, Fine Sand)
Crude oil often contains H₂S, salts, wax, gums, asphaltenes, and trace sand. Materials must be resistant to sulphide stress cracking, abrasion, and corrosion:
Casing/Volute: Carbon steel (A36/WCB), 12% chrome (CA6NM), or duplex stainless steel – NACE MR0175 compliant.
Impeller: 12% chrome, 316L, or duplex – closed type, wear rings, dynamically balanced.
Shaft: 4140/42CrMo, 17‑4PH, or duplex – large diameter, low deflection (≤0.05 mm per 100 mm).
Bearing housing / seal chamber: Carbon steel or stainless steel with abrasion‑resistant bushings.
Applicable Crude Oil Media & Services
Fully applicable:
Light, medium, heavy crude oil; condensate; atmospheric/vacuum distillates; refinery residues (low solids).
Sour crude (H₂S), acidic crude (organic acids), salty crude, waxy crude, crude with trace sand (≤3%, particles <100 μm).
Viscosity up to 500 cP (optimal ≤200 cP).
Low‑temperature to high‑temperature crude, offshore platform crude, oilfield produced fluids (oil/water mixtures).
Crude reflux, tower overhead reflux, side‑stream draw‑off, tank farm transfer, pipeline boosting.
Limit or avoid (use BB between‑bearing pumps instead):
High abrasion, large particles (>100 μm, solids >5%) – rapid impeller wear.
Very high viscosity (>500 cP), severe asphaltene fouling, crystallising fluids – low efficiency, cavitation risk.
Flow >3000 m³/h, head >380 m, pressure >110 bar – beyond overhung pump capability.
Highly corrosive non‑hydrocarbon media (strong acids/bases) – unless special alloys.
Optimal refinery / oilfield services:
Crude unit charge pump (atmospheric / vacuum distillation feed).
Crude transfer pump (tank farm to refinery).
Pipeline booster pump for crude oil.
Offshore platform crude lift / export pump.
Reflux and side‑stream pumps in crude towers.
Essential Auxiliary Systems for Crude OH2
1. Sealing System – API 682
Preferred: Dual mechanical seals (Plan 53 or 54) with barrier fluid – prevents crude leakage, handles sour service, explosion‑safe.
Alternative: Single seal with API Plan 11 or 32 (for clean, low‑sulphur light crude).
Prohibited: Packed gland seals – unsafe for crude.
2. Bearing & Lubrication
Heavy‑duty bearings: radial cylindrical roller + angular contact thrust bearings (for high axial thrust from crude).
Lubrication: Oil ring or forced oil circulation with cooler / fan. Bearing housing equipped with temperature and vibration monitoring.
Bearing isolators: non‑contact labyrinth seals – keep crude vapours and moisture out.
3. Crude‑specific features
Steam / electric tracing – jacketed casing for waxy crude to prevent solidification and reduce viscosity (maintain 60–150°C).
Flushing / cooling – seal flush (Plan 11/32), bearing cooling water.
Monitoring – Vibration (accelerometer), bearing temperature (RTD), seal leakage (pressure switch), suction/discharge pressure and temperature – per API 610 on‑line monitoring requirements.
Selection Summary – When to Use API 610 OH2 Crude Oil Pump
| Condition | Recommendation |
|---|---|
| Medium‑high pressure (≤110 bar), medium‑high temperature (≤450°C), continuous refinery/oilfield service | OH2 – optimal |
| Sour (H₂S), waxy, salty, trace sand crude | OH2 with NACE MR0175, dual seals, tracing |
| Flow 100–2000 m³/h, head ≤250 m, speed 1480 rpm | OH2 – most economical and reliable |
| High abrasion, large particles, solids >5% | Use BB2/BB3 between‑bearing pumps |
| Flow >3000 m³/h, head >380 m, pressure >110 bar | Use BB3/BB5 |
| Very high viscosity (>500 cP) or severe fouling | Consider positive displacement pump or heated BB pump |
Why OH2 is the Crude Oil Workhorse
The centerline‑mounted design ensures that high operating temperatures (e.g., 200–400°C) do not misalign the shaft – the casing expands evenly around the centreline. Its overhung configuration allows a compact footprint while the back pull‑out feature minimises maintenance downtime. When combined with API 682 dual seals and NACE MR0175 materials, the OH2 pump delivers safe, long‑life operation on crude oil services that would quickly destroy lesser pump types.
For complete technical datasheets, sizing assistance, or a quotation for any API 610 OH2 crude oil pump, please contact info@hyrig.com. We respond within 24 hours.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.