HYRIG can supply the API 599 sleeve type plug valve range. The sleeve type plug valve uses a PTFE liner (sleeve) between the plug and the body to provide a bubble-tight seal. It is designed for 90-degree on/off operation in chemical processing and water treatment where a cavity-free design is required.
| NPS | DN | Class 150 L (mm) | Class 150 H (mm) | Class 150 Wt (kg) | Class 300 L (mm) | Class 300 H (mm) | Class 300 Wt (kg) |
|---|---|---|---|---|---|---|---|
| 1/2 | 15 | 108 | 110 | 8.5 | 140 | 110 | 9.5 |
| 1 | 25 | 127 | 115 | 10.5 | 165 | 115 | 12 |
| 2 | 50 | 178 | 150 | 18 | 216 | 150 | 20 |
| 3 | 80 | 203 | 180 | 26 | 283 | 180 | 29 |
| 4 | 100 | 229 | 380 | 40 | 305 | 380 | 53 |
| 6 | 150 | 267 | 520 | 70 | 403 | 520 | 85 |
| 8 | 200 | 292 | 580 | 130 | 419 | 580 | 185 |
| 12 | 300 | 356 | 680 | 381 | 502 | 680 | 390 |
Data source: Technical data table.
| Dimension | Standard |
|---|---|
| Face-to-face | ASME B16.10 / API 6D |
| Flanged ends | ASME B16.5 |
| Butt weld ends | ASME B16.25 |
| Pressure-temperature rating | API 599 |
The valve consists of a tapered plug rotating inside a PTFE sleeve. The sleeve is inserted into the valve body, and the plug is seated inside it. When the plug rotates 90 degrees, the through-port aligns with the pipeline, opening the valve. The PTFE sleeve acts as the primary seal, providing a bubble-tight shutoff with low operating torque.
Unlike a ball valve, which has a cavity between the ball and the body, the sleeve type plug valve has no void space where solids can accumulate. This cavity-free design makes it suitable for abrasive slurries or viscous fluids that would otherwise cause a ball valve to jam. The soft PTFE sleeve also provides a wiping action as the plug rotates, clearing the seating surface.
Replacing a ball valve or another plug valve requires verification of four factors:
Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.
Q: What is the difference between a sleeve type plug valve and a lubricated plug valve?
A sleeve type uses a PTFE liner for soft sealing and is suitable for chemical service. A lubricated type injects sealant to maintain sealing in high-pressure or dry gas service.
Q: Can a sleeve type plug valve be used for steam?
No. The PTFE sleeve has a limited temperature range. For high-temperature steam, a metal-seated or lubricated plug valve is required.
Q: What is the advantage of a plug valve over a ball valve for slurries?
A plug valve has no cavity between the plug and the body, so solids cannot accumulate. A ball valve has a cavity that can trap particles and cause the valve to jam.
Q: What is the typical lead time?
Standard lead time is 4 to 6 weeks depending on size, class, and material.
To confirm the correct sleeve type plug valve for your line, provide the medium, operating temperature, pressure class, and end connection. Our engineering team will verify the sleeve material and valve dimensions.
For API 599 sleeve type plug valve selection, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.