The API 610 BB2 high temperature bottom pump is a between‑bearing, single‑stage, single‑suction, radially split horizontal centrifugal pump. It is the refinery standard for atmospheric tower bottom, vacuum tower bottom, fractionator bottom, and other high temperature heavy oil services. Unlike overhung OH2 pumps, the BB2 configuration places the impeller between two bearing sets, providing extreme shaft rigidity, minimal deflection, low vibration, and excellent tolerance to thermal expansion and nozzle loads.
Why BB2 for High Temperature Bottom Service
Between bearing support – impeller located between two bearings. Shaft stiffness is much higher than OH2, eliminating deflection and vibration at high temperatures and heavy fluid viscosities.
Radially split casing – uniform thermal expansion, no distortion, maintains alignment. Easier maintenance than axially split casings for hot services.
Superior nozzle load capacity – handles heavy piping stresses from thermal expansion of tower connections.
Applicable Media (High Temperature Bottom Exclusive)
Fully applicable:
Atmospheric tower bottom heavy oil
Vacuum tower bottom residue (vacuum resid)
Waxy oil, catalytic slurry oil, circulating oil, hot feed
Heavy diesel, heavy aromatics, high temperature fuel oil, gas oil
Fluids with trace coke fines, catalyst fines, or mild coking tendency
Not recommended:
Highly volatile light hydrocarbons (gasoline, naphtha, LPG, condensate) – OH2 is preferred for those services.
Operating Envelope (Key BB2 Advantage)
Temperature: 250 – 420°C (OH2 limit is typically ≤280°C)
Pressure: Medium to high – Class 300, 600, or 900
Flow: Medium to high (100 – 5000 m³/h)
Service: 24/7 continuous, heavy duty, severe process conditions
Fluid properties: High viscosity, high temperature, coking tendency, trace solids, high axial thrust
Critical Design & Configuration for High Temperature Bottom
Between bearing support – bearings straddle the impeller. Rigid shaft, low vibration, handles high axial thrust and radial loads.
Radially split casing – uniform thermal expansion, no flange binding, easy access to rotor for maintenance without disturbing piping.
Forced lubrication with cooling – high heat conduction from hot fluid requires:
Oil cooler (water or air) or fan cooling
Forced feed lubrication (lube oil console) – prevents bearing seizure at high temperature
API 682 mechanical seals (dual seals mandatory) – high temperature heavy oil tends to coke and foul seal faces.
Standard: Dual mechanical seals (pressurised) with Plan 54 (external barrier fluid circulation) or Plan 53B (pressurised with bladder accumulator)
Barrier fluid isolates process fluid from seal faces, prevents coking and fouling.
Seal chamber steam jacketed to keep fluid fluid and avoid solidification.
Steam jacketing & insulation – pump casing, cover, and seal chamber fitted with steam or thermal oil jackets. Prevents heavy oil from cooling, solidifying, or coking inside the pump during standby or low flow.
Materials – Heat resistant alloys
Casing: WC9 (1-1/4Cr-1/2Mo) or C12A (9Cr-1Mo-V) – high temperature creep resistant, good thermal fatigue resistance.
Impeller / wear rings: 12% chrome (CA6NM) or heat resistant stainless steel – resists erosion from fines and coking.
Shaft: high strength heat resistant alloy steel (e.g., 4140 hardened and tempered for high temperature).
Comparison – OH2 vs. BB2 for Tower Bottom Service
| Feature | OH2 (Overhung) | BB2 (Between Bearing) |
|---|---|---|
| Temperature limit | ≤280°C (practical) | 250‑420°C (standard) |
| Shaft rigidity | Lower – overhung, deflection under high load | Very high – impeller between bearings |
| Vibration | Higher risk at high temperature | Very low, stable |
| Axial thrust handling | Limited – heavy thrust may require duplex bearings | Excellent – balanced design |
| Coking / solids tolerance | Moderate | High – thicker wear parts, radial split easy cleaning |
| Typical refinery service | Clean light/medium hydrocarbons (dies, kerosene, crude) | Tower bottom, resid, slurry, waxy oil |
Why API 610 BB2 is the Only Choice for High Temperature Bottom Pumps
Between bearing construction eliminates high temperature deflection and vibration that cause seal and bearing failures in OH2 pumps.
Radially split casing withstands thermal cycling without leakage or misalignment.
Forced lubrication with cooling and steam jacketing are mandatory – integrated into standard BB2 design.
Dual mechanical seals with Plan 54 or 53B barrier fluid systems prevent coking at seal faces – the number one failure mode in hot heavy oil service.
WC9/C12A materials provide long creep life at 400°C+.
Standards & Compliance
API 610 (12th Edition) – BB2 type
API 682 – dual mechanical seals, Plan 54/53B
NACE MR0175 (if sour resid)
ASME B16.5 flanges (Class 300/600/900)
ISO 13709
For complete technical datasheets, sizing assistance, or a quotation for any API 610 BB2 high temperature bottom pump (atmospheric bottom, vacuum bottom, slurry, waxy oil), please contact info@hyrig.com. We respond within 24 hours.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.