API 610 BB2 Residue Pump – Between Bearing Radial Split for Atmospheric & Vacuum Residue Service

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 BB2 residue pump – mandatory for atmospheric residue, vacuum residue, heavy fuel oil, ultra heavy crude. Between bearing, radial split, handles 300‑420°C, high viscosity, coking tendency, and fine coke particles. Features steam jacketing, forced lube oil cooling, API 682 dual seals (Plan 53B/54), WC9/C12A high temperature alloy. OH2 prohibited. Flow up to 5000 m³/h. Contact info@hyrig.com
Conatct For Details
DetailReview(0)Additional

The API 610 BB2 residue pump is a between‑bearing, single‑stage, single‑suction, radially split horizontal centrifugal pump. It is the mandatory pump type for handling atmospheric residue, vacuum residue, heavy fuel oil, ultra‑heavy crude, and other high‑temperature, high‑viscosity, coking‑prone refinery bottom streams. Overhung OH2 pumps are strictly prohibited for these services because their flexible shaft, lower rigidity, and higher vibration lead to rapid failure under high temperature, heavy loads, abrasive fines, and coking conditions.

Why BB2 is Mandatory for Residue

  • Between bearing support – impeller located between two bearings. Extremely rigid shaft, minimal deflection, low vibration even at 400°C.

  • Radially split casing – uniform thermal expansion, no distortion, easy maintenance without disturbing piping.

  • Superior heavy load capacity – handles high axial thrust, radial loads, and piping stresses from tower connections.

Applicable Media

  • Atmospheric residue (long residue)

  • Vacuum residue (short residue, vacuum resid)

  • Heavy fuel oil, ultra‑heavy crude oil

  • Tower bottom high temperature heavy oil

  • Coker feed, heavy waxy oil mixed with residue

  • Fluids containing fine coke dust, carbon particles, and trace abrasives

All share: high temperature (300‑420°C), high viscosity, coking tendency, poor flowability, and fine solids.

Operating Parameters

  • Temperature: 300 – 420°C (among the hottest refinery services)

  • Viscosity: High to ultra‑high – solidifies upon cooling

  • Solids: Fine coke powder, carbon fines, trace abrasive particles

  • Operation: 24/7 continuous, heavy duty, strong coking tendency

Critical Design Features for Residue BB2

  1. Structural advantage – between bearing, short rigid shaft. High temperature low deflection, anti‑vibration, wear resistant, handles large axial thrust.

  2. Pump casing – radially split with full steam / thermal oil jacketing. Prevents residue from cooling, solidifying, and coking inside flow passages.

  3. Lubrication & cooling – bearing housing with water cooling + forced feed lubrication. Eliminates bearing seizure from heat conduction.

  4. Mechanical seals (API 682 mandatory) – dual mechanical seals (pressurised).

    • Preferred plans: Plan 53B (bladder accumulator) or Plan 54 (external barrier fluid circulation).

    • Barrier fluid is cooled and circulated – prevents coke build‑up on seal faces, eliminating the most common failure mode.

  5. Heat & abrasion resistant materials (residue specific)

    • Casing: WC9 (1-1/4Cr-1/2Mo) or C12A (9Cr-1Mo-V) – high temperature creep resistant, good thermal fatigue resistance.

    • Impeller / wear rings: 12% chrome (CA6NM) or heat resistant wear alloy – resists erosion from coke fines.

    • Shaft: high strength heat resistant alloy steel.

Strict Pump Type Classification (Complete Refinery Media)

Pump TypeServices
OH2 (overhung)Gasoline, naphtha, LPG, condensate, aromatics, solvent oil, kerosene, jet fuel, diesel, conventional crude – clean, low to medium temperature, low solids, light to medium oils
BB2 (between bearing)Atmospheric residue, vacuum residue, catalytic slurry, high temperature tower bottom, hot waxy oil, heavy coker oil – ultra‑high temperature, high viscosity, coking, fines, heavy duty continuous
BB1High flow circulating water, large flow crude oil / diesel double‑suction services
BB3/BB4High pressure multistage – boiler feed, high pressure hydrogenation feed

Comparison – OH2 vs. BB2 for Residue Service

FeatureOH2 (Overhung)BB2 (Between Bearing)
Suitability for residueNot permittedMandatory
Shaft rigidityLower – overhang, deflection under high loadVery high – impeller between bearings
Vibration at high temperatureHigh riskLow, stable
Axial thrust capacityLimitedExcellent – balanced design
Coking / fines tolerancePoor – high failureGood – thick wear parts, jacketed, dual sealed
Temperature limit≤280°C practical300‑420°C standard
JacketingNot typicalFull steam jacketing

Why API 610 BB2 is the Only Choice for Residue

  • Between bearing construction eliminates high temperature deflection and vibration that cause premature failure in OH2 pumps.

  • Radially split casing with steam jacketing prevents solidification and coking.

  • Forced lubrication with cooling maintains bearing integrity at 400°C+.

  • Dual mechanical seals with Plan 53B/54 barrier systems prevent seal face coking – the number one failure mode in hot heavy oil service.

  • WC9/C12A materials provide long creep life and resistance to thermal fatigue.

Standards & Compliance

  • API 610 (12th Edition) – BB2 type

  • API 682 – dual mechanical seals, Plan 53B or 54

  • NACE MR0175 (if sour residue contains H₂S)

  • ASME B16.5 flanges (Class 300/600/900)

For complete technical datasheets, sizing assistance, or a quotation for any API 610 BB2 residue pump (atmospheric residue, vacuum residue, fuel oil, heavy crude), please contact info@hyrig.com. We respond within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit