API 610 BB2 Wax Oil Pump – Between Bearing Radial Split for Refinery Wax Oil & Hot Fractions

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 BB2 wax oil pump – between bearing, radial split, single‑stage. Designed for atmospheric wax oil, vacuum wax oil, heavy wax oil, and hot refinery fractions at 220‑380°C. High viscosity, solidifies upon cooling, trace coke fines. Features steam jacketing, API 682 dual seals (Plan 53B/54), forced lube cooling, 12Cr impeller. OH2 only for low temperature clean service. Flow up to 4000 m³/h. Contact info@hyrig.com
Conatct For Details
DetailReview(0)Additional

The API 610 BB2 wax oil pump is a between‑bearing, single‑stage, single‑suction, radially split horizontal centrifugal pump. It is the preferred pump type for handling atmospheric wax oil, vacuum wax oil, light/heavy wax oil, catalytic cracker feed, hydrocracker feed, and other hot middle distillate fractions in refineries. While a few low temperature, clean, low flow wax oil services may use OH2 (overhung) pumps, the majority of refinery side‑stream and high temperature wax oil services require BB2 for reliable long‑term operation.

Why BB2 is Recommended for Wax Oil (Most Cases)

  • Between bearing support – impeller between two bearings. Rigid shaft, minimal thermal deflection, low vibration.

  • Radially split casing – uniform thermal expansion, no distortion. Suitable for long term high temperature duty.

  • Jacketing capability – full steam or thermal oil jacketing prevents wax oil from cooling, solidifying, and plugging.

  • High axial thrust capacity – handles high viscosity, heavy load service.

Applicable Media

  • Atmospheric wax oil, vacuum wax oil

  • Light wax oil, heavy wax oil, raffinate

  • Catalytic cracker feed, hydrocracker feed

  • Hot middle distillates, side‑stream cuts from atmospheric/vacuum towers

Media Characteristics

  • Temperature: 220 – 380°C (high temperature service)

  • Viscosity: Medium to high – solidifies upon cooling (requires jacketing)

  • Solids: Trace coke fines, slight coking tendency

  • Other: Non‑volatile, no cavitation risk; continuous heavy duty operation as hot feed

Operating Parameters

  • Temperature: 220‑380°C

  • Pressure: Class 300/600 typical

  • Flow: Medium to high – up to 4000 m³/h

  • Operation: 24/7 continuous, heavy duty

Key Design Features for Wax Oil BB2

  1. Casing – radially split, heat resistant carbon/alloy steel, full steam jacketing plus insulation. Prevents wax freezing and coking.

  2. Sealing (API 682 mandatory) – dual mechanical seals (pressurised).

    • Preferred plans: Plan 53B (bladder accumulator) or Plan 54 (external barrier fluid circulation).

    • Barrier fluid circulation prevents wax from coking on seal faces.

  3. Bearing & lubrication – forced feed lubrication with oil cooler. Dissipates conducted heat from hot fluid, prevents bearing seizure.

  4. Materials

    • Casing: Heat resistant carbon steel (WC6, WC9) or alloy steel.

    • Impeller / wear rings: 12% chrome (CA6NM) – resists erosion from trace fines.

    • Shaft: High strength alloy steel.

When is OH2 Permissible for Wax Oil?

OH2 may be considered only for:

  • Very low temperature (≤200°C) wax oil

  • Clean wax oil, no solids or coking tendency

  • Small flow (≤300 m³/h)

  • Non‑continuous or low duty service

For all other wax oil duties – BB2 is mandatory.

Comparison – Wax Oil Pump Selection

ConditionRecommended PumpReason
High temperature (220‑380°C), any flowBB2Rigid shaft, jacketing, dual seals, thermal stability
Low temperature (≤200°C), clean, small flowOH2 possibleLower cost, simpler
Any wax oil with coking tendency or finesBB2 mandatoryAnti‑coking features (jacketing, dual seals)
Continuous heavy dutyBB2Fatigue resistance, axial thrust capacity

Refinery Medium Classification – Complete Interface (OH2 vs. BB2)

Pump TypeServices
OH2 (overhung)Gasoline, naphtha, LPG, condensate, aromatics, solvent oil, kerosene, jet fuel, diesel, clean ambient crude – volatile, low‑medium temperature, clean, light to medium oils
BB2 (between bearing)Wax oil, atmospheric residue, vacuum residue, catalytic slurry, high temperature tower bottom, hot waxy oil, heavy coker oil – high temperature, high viscosity, solidifying, coking tendency, trace fines, continuous heavy duty
BB1High flow circulating water, large volume crude/diesel double suction
BB3/BB4High pressure multistage (boiler feed, hydrogenation feed)

Why BB2 is the Workhorse for Wax Oil

  • Between bearing construction eliminates high temperature shaft deflection and vibration that cause seal and bearing failures in OH2 pumps.

  • Steam jacketing ensures wax oil remains fluid during standby and low flow, preventing solidification and coking.

  • Dual mechanical seals with barrier fluid circulation protect seal faces from coke deposits.

  • Forced lube with cooling handles conducted heat, extending bearing life.

For complete technical datasheets, sizing assistance, or a quotation for any API 610 BB2 wax oil pump (atmospheric, vacuum, light, heavy wax oil), please contact info@hyrig.com. We respond within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit