API 610 OH2 Diesel Pump – Centerline‑Mounted Overhung Pump for Middle Distillates

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
The API 610 OH2 diesel pump is a horizontal, overhung, centerline‑mounted single‑stage end suction centrifugal pump built for diesel, gas oil, kerosene, and other middle distillates. It is the refinery’s most cost‑effective product pump for continuous service. Features moderate NPSH design (NPSHa ≥ NPSHr + 0.5–1.0 m), API 682 single mechanical seal (Plan 11) for clean diesel, WCB carbon steel casing, 12% chrome impeller, and Ex d IIB T4 explosion‑proof rating. Back pull‑out design. Contact info@hyrig.com

Conatct For Details
DetailReview(0)Additional

The API 610 OH2 (Overhung Type 2) diesel pump is the refinery standard for handling diesel, gas oil, kerosene, and other middle distillates. Positioned between light hydrocarbons (gasoline) and heavy crude, the diesel OH2 pump offers the best balance of simplicity, reliability, and safety – without the extreme cavitation risk of gasoline or the high‑viscosity and heating requirements of crude oil. Its centerline‑mounted casing (OH2, not foot‑mounted OH1) ensures thermal stability and resistance to pipe strain for continuous refinery operation.

Structural Definition – OH2 per API 610

  • Horizontal, single‑stage, single‑suction, end suction (axial inlet, radial/top discharge).

  • Centerline‑mounted – casing supported from the centreline flange.

  • Overhung impeller – mounted at the shaft end, outside the bearing housing.

  • Radially split volute casing.

  • Closed impeller.

  • Back pull‑out design – rotor, seal, and bearing housing removable without disturbing piping or motor.

  • Heavy‑duty bearing housing with temperature and vibration monitoring.

Applicable Media – Diesel & Middle Distillates

Fully applicable:

  • 0# / -10# finished diesel, atmospheric gas oil, catalytic diesel, hydrotreated diesel.

  • Light diesel, heavy diesel, intermediate diesel components, kerosene, jet fuel (Jet A/A‑1).

  • Tank farm transfer, unit feed, reflux, truck loading, pipeline export.

Not applicable (use other pump types):

  • High concentrations of fine catalyst fines, abrasive solids, high‑solids oily sludge.

  • Pyrolysis heavy oil (high temperature cracking residue), strong corrosive acids/bases.

Media & Operating Characteristics – Unique to Diesel

Diesel sits between gasoline and crude oil in key properties:

PropertyGasolineDiesel (Middle Distillate)Crude Oil
ViscosityVery low (0.3–1 cP)Low to moderate (2–10 cP)Moderate to high (5–500 cP)
Volatility / Vapour pressureVery highLow to moderateVery low
Flash point≤ –40°C (extremely flammable)55–80°C (combustible)Varies (often >60°C)
Cavitation riskVery high (requires inducer often)ModerateLow (but NPSH still important)
Heating/tracingNot requiredNot required (ambient to 160°C)Often required (waxy crude)
CorrosivityLow (copper‑free mandatory)Low to moderate (sour crude may need NACE)Sour crude requires NACE

Performance Boundaries (Diesel Duty)

  • Flow: 20 – 3000 m³/h (typical 50 – 2000 m³/h)

  • Head: 20 – 300 m (single‑stage)

  • Design pressure: Up to 5.0 MPa (50 bar) – typically Class 150/300; Class 600 for high‑pressure services

  • Temperature: –20°C to +180°C (ambient to warm diesel; no heavy‑oil high temperatures)

  • Speed: 1480 or 2980 rpm (both common)

  • NPSH requirement: NPSHa ≥ NPSHr + 0.5–1.0 m – moderate; inducer optional only for low NPSHa

Key Design Configuration – Diesel OH2 Standard

1. Hydraulic Design & Cavitation

  • Closed impeller with standard NPSH characteristics (no advanced inducer needed for typical refinery NPSHa).

  • Wear rings (replaceable) for long life when handling minor coke fines or catalytic fines.

  • NPSHa margin of 0.5–1.0 m is adequate – significantly less strict than gasoline.

2. Mechanical Sealing – API 682 (Cost‑Effective)
Diesel is less volatile than gasoline and less corrosive than sour crude, allowing simpler, lower‑cost sealing.

  • Clean hydrotreated diesel (sulphur ≤10 ppm): Single mechanical seal with API Plan 11 or 21 (self‑flush from pump discharge). Reliable, low maintenance, lowest cost.

  • Sour diesel (high H₂S) or mildly dirty service: Dual mechanical seal (pressurised) with Plan 53A – prevents hazardous gas release.

  • Heavy diesel or coker diesel with fines: Single seal with Plan 32 (external clean flush) to protect seal faces from abrasion.

  • Prohibited: Packed gland seals – still unsafe for any hydrocarbon service.

3. Material Combination (Diesel Standard)

  • Casing: WCB carbon steel (standard); LCC for low‑temperature service.

  • Impeller / Wear rings: 12% chrome (CA6NM) or 316L stainless steel – corrosion resistant, good abrasion resistance.

  • Shaft: High‑strength alloy steel (4140/42CrMo) – high rigidity, low deflection.

  • Copper‑free requirement: Recommended to prevent gum formation and comply with APIRP 2003 (though not as strictly enforced as for gasoline). Most refineries specify copper‑free for all hydrocarbon pumps.

  • NACE MR0175: Required for sour diesel containing H₂S.

4. Explosion‑Proof & Safety

Diesel has a higher flash point (typically >55°C) than gasoline, reducing risk in normal operation, but electrical area classification still applies for refineries and terminals.

  • Motor & pump assembly: ATEX / IECEx certified for hazardous area (Zone 1 or Zone 2 as per site classification).

  • Gas group: IIB (diesel hydrocarbons).

  • Temperature class: T4 (135°C auto‑ignition protection) – less stringent than gasoline T6.

  • Anti‑static features: Shaft and casing grounding; flange earthing straps.

  • Bearing housing isolation: Labyrinth seals prevent vapour ingress.

5. Bearing & Lubrication

  • Heavy‑duty angular contact thrust bearings (match diesel’s moderate axial thrust).

  • Lubrication options: Oil mist (preferred for continuous refinery units), oil ring with constant level oiler, or forced lube for high‑speed high‑power pumps.

  • Bearing temperature RTD and vibration monitoring (API 670 Level II or III depending on service).

6. Support & Construction

  • Centerline support (OH2) – even thermal expansion, handles pipe strain well.

  • Heavy‑duty bearing housing – supports long rotor for 2980 rpm operation.

  • Back pull‑out design – allows seal and bearing replacement without removing casing from piping – minimises downtime.

Why OH2 (Not OH1 or BB) for Diesel

Pump TypeSuitability for DieselReason
OH2 (centerline)OptimalThermal stability, pipe load capacity, back pull‑out. Standard refinery diesel pump.
OH1 (foot‑mounted)Not allowedPoor thermal alignment, lower nozzle load rating, not compliant with many refinery specifications.
BB2/BB3 (between‑bearing)Over‑specifiedHigher cost, larger footprint; only justified for flow >3000 m³/h, head >300 m, or extreme pressure.

Comparison – Gasoline OH2 vs. Diesel OH2 vs. Crude OH2

FeatureGasoline OH2Diesel OH2Crude OH2
Cavitation riskVery highModerateLow
NPSH margin required≥1.0–1.5 m≥0.5–1.0 m≥0.5–1.0 m
InducerOften neededOptional (rare)Not required
Sealing typeDual seal mandatory (Plan 53/54)Single seal (Plan 11) for clean diesel; dual for sourDual seal for sour crude
Explosion classEx d IIB T4/T6Ex d IIB T4Ex d IIB T4 (typical)
Copper‑freeMandatoryRecommendedNot required
Heating/tracingNoNoYes for waxy crude
Material upgradeWCB + 12Cr/316LWCB + 12Cr (standard)Duplex / NACE alloys
Typical speed2980 rpm1480 or 2980 rpm1480 rpm
Lifecycle costHigher (complex sealing)Lowest (simple single seal)Higher (expensive materials)

Why Diesel OH2 is the Refinery Workhorse

  • Cost‑effective simplicity: Single mechanical seal with Plan 11 is sufficient for most diesel services – far lower capital and operating cost than dual‑seal pumps required for gasoline or sour crude.

  • Moderate requirements: No extreme cavitation margin, no heating/tracing, no exotic alloys – diesel OH2 is a standard catalog pump for most manufacturers.

  • Reliability: Centerline support and heavy bearings ensure 3+ years of continuous operation – matches refinery turnaround cycles.

  • Maintainability: Back pull‑out design allows seal replacement without breaking pipe flanges – typical diesel pump maintenance takes only a few hours.

For complete technical datasheets, sizing assistance, or a quotation for any API 610 OH2 diesel pump, please contact info@hyrig.com. We respond within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit