API 610 Seawater Lift Pump Types – Comprehensive Selection Guide for Offshore & Onshore Applications

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Selecting the right API 610 pump for seawater lift depends on installation, flow, head, and corrosion resistance. This guide covers six compliant structures: VS1 (long-shaft vertical), VS6 (submersible direct-coupled), BB1 (horizontal double-suction), VS0 (submersible single-stage), OH2 (horizontal overhung), and BB3 (horizontal multistage). Includes a selection decision matrix and material recommendations (super duplex 2507). Contact info@hyrig.com for engineering support.

Conatct For Details
DetailReview(0)Additional

Seawater lift pumps are critical for firewater systems, cooling water intake, and process water supply on offshore platforms, FPSOs, refineries, and desalination plants. The API 610 standard defines several pump types suitable for seawater duty. Below is a structured guide to the most relevant types, ranked by application priority, including their structural definition, seawater adaptability, typical applications, and representative models.

1. VS1 (Vertically Suspended Type 1) – Vertical Turbine Pump

Structural Definition (API 610)
Vertically suspended, single‑case, diffuser bowl design. Impeller and bowl assembly submerged in seawater, connected to an above‑grade motor via a long drive shaft. Discharge through a column pipe.

Seawater Adaptability

  • Compact vertical footprint – ideal for space‑limited offshore platforms and FPSOs.

  • Multistage bowls deliver stable heads up to 2000 ft (610 m).

  • Wetted parts available in duplex or super duplex stainless steel for chloride corrosion resistance.

Typical Applications

  • Offshore platform firewater lift

  • FPSO seawater cooling intake

  • Near‑shore drilling rig seawater transfer

Representative Models
Sulzer SJT series, National Pump VS1 vertical turbine pump.

2. VS6 (Vertically Suspended Type 6) – Submersible Direct‑Coupled Pump

Structural Definition (API 610)
Motor and pump directly coupled as a single, fully submerged unit. No long shaft, no intermediate bearings. Single or multistage. Mounted via a top bracket to the sea chest or tank.

Seawater Adaptability

  • No long shaft wear or vibration – extremely low failure rate.

  • Maintenance interval ≥10,000 hours.

  • IP68 protection – permanent immersion in seawater.

  • Wetted parts in super duplex stainless steel (2507) – excellent chloride resistance.

Typical Applications

  • FPSO sea chest seawater intake

  • Deep‑sea drilling ship seawater lift

  • Large offshore engineering raw water supply

Representative Models
Sulzer SJS series submersible seawater pump, Inno Pumps VS6 vertical multistage pump.

3. BB1 (Between Bearing Type 1) – Axially Split, Double‑Suction Pump

Structural Definition (API 610)
Horizontal installation, axially split volute casing. Single‑stage, double‑suction impeller located between two bearing sets. High structural rigidity.

Seawater Adaptability

  • Double‑suction design provides very high flow rates (up to 25,000 gpm).

  • Low NPSH requirement – excellent cavitation resistance.

  • Axially split casing allows easy maintenance without disturbing piping – ideal for continuous operation.

Typical Applications

  • Land‑based refinery seawater circulation systems

  • Port and terminal seawater lift stations

  • Large seawater desalination plant intake

Representative Models
Sulzer HSA series, AxFlow BB1 double‑suction pump.

4. VS0 (Vertically Suspended Type 0) – Submersible Vertical Pump

Structural Definition (API 610)
Submersible motor drive, vertically suspended. Single‑stage turbine bowl. No exposed drive shaft. Suitable for deep wells or deep tanks.

Seawater Adaptability

  • Submersion depth up to 15 metres – for moderate deep‑sea intake.

  • Simple construction, low maintenance cost.

  • Wetted parts can be specified in 316L or duplex stainless steel.

Typical Applications

  • Near‑shore platform emergency seawater lift

  • Offshore wind turbine platform cooling water intake

Representative Models
National Pump VS0 submersible vertical turbine pump.

5. OH2 (Overhung Type 2) – Horizontal Overhung, Centreline Support

Structural Definition (API 610)
Horizontal installation, radially split volute, single‑stage end suction. Impeller overhung from the bearing housing. Centreline support maintains alignment during thermal expansion.

Seawater Adaptability

  • Suitable for land‑based small to medium seawater lift (flow ≤800 m³/h, head ≤100 m).

  • Limited to moderate pressures (<36 bar) and flows (<2000 m³/h) due to overhung rigidity.

Typical Applications

  • Port firewater seawater pump station

  • Small desalination plant pretreatment intake

Representative Models
Sulzer CPN/CPT series, Alond Pumps OH2 centrifugal pump.

6. BB3 (Between Bearing Type 3) – Axially Split, Multistage Pump

Structural Definition (API 610)
Horizontal installation, axially split casing. Multiple impellers in opposed arrangement, located between two bearing sets. Designed for high head.

Seawater Adaptability

  • Multistage design achieves very high heads (up to 10 MPa / 1450 psi).

  • Opposed impeller arrangement balances axial thrust – smooth operation.

  • Ideal for long‑distance seawater transmission or high‑pressure reverse osmosis feed.

Typical Applications

  • Seawater desalination high‑pressure RO feed

  • Long‑distance seawater transfer to offshore platforms

Representative Models
PumpWorks BB3 multistage pump, Boda BB3 series.


API 610 Seawater Lift Pump Selection Decision Matrix

API 610 TypeMountingKey Application ScenarioFlow RangeHead RangeCorrosion Protection Materials
VS1Vertical suspendedOffshore platforms / FPSO50 – 3500 m³/h20 – 1000 mDuplex / Super duplex SS
VS6Submersible verticalFPSO sea chest / deep sea intake300 – 2500 m³/h15 – 80 mSuper duplex 2507
BB1Horizontal between‑bearingLand‑based large flow intake100 – 10000 m³/h25 – 200 mDuplex SS / Monel
VS0Submersible verticalNear‑shore emergency lift5 – 500 m³/h10 – 140 m316L SS / Duplex
OH2Horizontal overhungLand‑based small to medium50 – 800 m³/h25 – 100 m316 SS / Cast iron + coating
BB3Horizontal between‑bearingHigh head seawater transfer50 – 500 m³/h100 – 1000 mSuper duplex SS

Key Selection Principles for Seawater Lift Pumps

  • Offshore / FPSO priority: VS series.
    Choose VS1 for conventional seawater lift with above‑deck motor. Choose VS6 for submersible sea chest intake – eliminates long shaft and intermediate bearings.

  • Land‑based large flow: BB1.
    For refineries, port stations, and continuous operation, BB1 double‑suction pumps provide high flow, low NPSH, and easy maintenance.

  • High head applications: BB3 or VS1.
    For desalination high‑pressure feed or long‑distance transfer, select BB3 (horizontal multistage) or VS1 (vertical multistage).

  • Material compliance:
    All seawater lift pumps must meet API 610 material classes (S‑8 / D‑1 / D‑2). Super duplex stainless steel (2507) or Monel is highly recommended for chloride corrosion resistance. Avoid standard austenitic stainless steels (304, 316) for prolonged seawater immersion.

For engineering support, detailed sizing, or a quotation for any API 610 seawater lift pump type, please contact info@hyrig.com. We respond within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit