Water treating processes – including seawater pretreatment, reverse osmosis (RO) high‑pressure feed, ultrafiltration (UF) backwash recycle, sludge return, and brine/wastewater disposal – require pumps that meet strict reliability, corrosion resistance, and pressure stability standards. The API 610 standard provides several pump types specifically suited to these duties. Below is a structured guide matching each water treating scenario with the optimal API 610 configuration.
Application: Transferring seawater from the lift point to pretreatment equipment such as sand filters, cartridge filters, or softening units.
Recommended API 610 Types: VS1, VS6, BB1
VS1 (Vertical Suspended Type 1)
Scenario: Offshore platform pretreatment systems – directly after the seawater lift pump, feeding filters.
Flow/Head: 50–3500 m³/h, 20–100 m.
Advantage: Same footprint and material (duplex/super duplex) as the lift pump – seamless integration, compact vertical layout matches platform pretreatment skids.
VS6 (Submersible Direct‑Coupled Type 6)
Scenario: FPSO pretreatment intake – direct pumping from sea chest to clarifier or filter. Immersion depth up to 30 m.
Advantage: No long shaft eliminates bearing fouling from suspended solids. Low maintenance, IP68 rated.
BB1 (Between Bearing Type 1 – Axial Split Double Suction)
Scenario: Large land‑based seawater pretreatment plants (e.g., desalination pretreatment buildings).
Flow/Head: 100–10,000 m³/h, 25–200 m.
Advantage: High flow, low NPSH, easy access to impeller for inspection – ideal for continuous service upstream of sand filters or activated carbon filters.
Application: Feeding pretreated seawater into RO membranes at 5–8 MPa (725–1160 psi) to produce fresh water.
Recommended API 610 Types: BB3, VS1 (high‑head versions)
BB3 (Between Bearing Type 3 – Axially Split Multistage)
Structural Definition: Horizontal, axially split, multiple impellers arranged in opposed pairs, bearings at both ends. Design pressure up to 10 MPa.
Scenario: Large seawater RO systems (desalination plants, offshore facilities).
Flow/Head: 50–500 m³/h, 100–1000 m (pressure up to 10 MPa).
Advantage: Opposed impeller design balances axial thrust – vibration ≤2.5 mm/s. Super duplex (2507) wetted parts meet API 610 S‑8 material class for high‑chloride seawater. Stable pressure matches RO membrane feed requirements.
Representative Models: PumpWorks BB3‑HP series, Sulzer HPD multistage high‑pressure pump.
VS1 (Vertical Suspended Multistage – High‑Head Version)
Scenario: Small offshore desalination units (e.g., drilling platform emergency freshwater supply).
Flow/Head: 50–3500 m³/h (smaller end), head 200–1000 m.
Advantage: Vertical footprint saves space – can be installed directly next to RO membrane skids, simplifying piping.
Application: Returning backwash water in ultrafiltration (UF) systems, recycling sludge from settling tanks, or circulating process water.
Recommended API 610 Types: OH2, VS6
OH2 (Overhung Type 2 – Horizontal Centreline Support)
Scenario: Land‑based UF backwash return, sludge return from clarifiers.
Flow/Head: 50–800 m³/h, 25–100 m.
Advantage: Overhung design allows easy access to impeller – ideal for cleaning debris or fibrous material from backwash water. Centreline support handles frequent start‑stop cycles (typical of intermittent backwash). Wetted parts in 316SS for mild corrosion resistance.
VS6 (Submersible Vertical)
Scenario: Under‑basin sludge return, submerged UF backwash lift.
Advantage: Fully submerged installation prevents sludge settling and clogging. IP68 rating for wet, corrosive environments. Maintenance interval ≥8,000 hours.
Application: Discharging concentrated brine (reject) from RO systems, or lifting wastewater from treatment ponds.
Recommended API 610 Types: BB1, VS0
BB1 (Axial Split Double Suction)
Scenario: Long‑distance brine discharge from large desalination plants.
Flow/Head: 100–10,000 m³/h, 25–200 m.
Advantage: High flow capacity. Axially split casing allows easy cleaning of salt crystal deposits. Wetted parts in Monel or super duplex for extreme chloride corrosion resistance.
VS0 (Vertically Suspended Type 0 – Submersible Single‑Stage)
Scenario: Emergency lift from wastewater holding tanks, brine sump dewatering.
Flow/Head: 5–500 m³/h, 10–140 m.
Advantage: Submersion depth up to 15 m. Single‑stage turbine bowl design resists fouling from suspended solids. Available in 316L or duplex stainless steel.
| API 610 Type | Core Water Treating Scenario | Flow Range | Head Range | Material Requirement | Key Advantage |
|---|---|---|---|---|---|
| VS1 | Seawater pretreatment, small RO feed | 50 – 3500 m³/h | 20 – 1000 m | Duplex / Super duplex | Vertical compact, seamless from lift |
| VS6 | Pretreatment intake, sludge return, emergency lift | 5 – 2500 m³/h | 15 – 140 m | Super duplex 2507 | Submerged, no shaft, low maintenance |
| BB1 | Large pretreatment, brine discharge | 100 – 10000 m³/h | 25 – 200 m | Duplex / Monel | High flow, low NPSH, easy inspection |
| BB3 | RO high‑pressure feed | 50 – 500 m³/h | 100 – 1000 m (up to 10 MPa) | Super duplex 2507 | Stable high pressure, balanced axial thrust |
| OH2 | UF backwash, sludge return, recycle | 50 – 800 m³/h | 25 – 100 m | 316 SS | Simple design, frequent start‑stop capable |
| VS0 | Brine sump, wastewater emergency | 5 – 500 m³/h | 10 – 140 m | 316L / Duplex | Deep immersion, fouling‑resistant |
To ensure smooth process continuity and cost‑effective design, follow these structural alignment principles:
Same structure compatibility: If the seawater lift pump is VS1 or VS6, use the same type for pretreatment to reduce piping changes and installation complexity (e.g., VS6 submerged pump directly feeding a pretreatment filter inlet).
Pressure matching for RO: For RO high‑pressure feed, BB3 is preferred over single‑stage pumps. Its multistage design matches RO membrane pressure requirements (5–8 MPa) without additional booster pumps.
Media adaptability: For streams containing suspended solids (sludge, backwash debris, salt crystals), choose anti‑clogging designs (VS6/VS0 submersible) or easily cleanable casings (BB1 axial split).
Regulatory compliance: All water treating pumps should meet API 610 12th Edition, ISO 13709, and where potable water contact occurs, NSF/ANSI 61 certification (drinking water system components). Contact us for certified options.
For engineering assistance, detailed pump sizing, or a quotation for any API 610 water treating pump, please contact info@hyrig.com. We respond within 24 hours.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.