API 610 Pumps for Sulfate Removal Units (SRU) – Complete Selection Guide

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Sulfate Removal Units (SRU) use nanofiltration (NF) membranes to remove divalent sulfate ions from seawater, preventing barium/strontium sulfate scaling in oil reservoirs. Selecting the right API 610 pump is critical: BB2 for medium‑pressure high‑flow feed, BB3 for high‑pressure NF duty, BB5 for extreme conditions, VS1 for compact offshore footprints, and VS6 for submerged pretreatment lifts. This guide covers flow/head ranges, anti‑scaling features, and material compatibility. Contact info@hyrig.com

Conatct For Details
DetailReview(0)Additional

Sulfate Removal Units (SRU) employ nanofiltration (NF) membranes to remove divalent sulfate ions (SO₄²⁻) from seawater injection streams. This prevents barium sulfate and strontium sulfate scaling in oil reservoirs, a critical requirement for offshore and onshore oilfield waterflood projects. SRU process demands:

  • High, stable pressure – matching NF membrane operating pressure (15–60 bar typical)

  • Anti‑scaling / corrosion resistance – sulfate crystals can deposit on impellers; seawater chlorides attack materials

  • Space adaptability – compact for offshore platforms (FPSO, rigs) or high‑flow for land‑based facilities

API 610 provides five pump types ideally suited to SRU duties. Below is a structured guide.


1. BB2 (Between Bearing Type 2) – Radially Split, Single‑Stage or Two‑Stage

Structural Definition (API 610)
Horizontal installation, radially split volute, single‑stage double‑suction or two‑stage configuration. Impeller(s) located between two bearing sets. Centreline support for thermal stability.

SRU Adaptability

  • Key Advantage: Double‑suction impeller provides wide flow coverage (up to 5000 m³/h) and low NPSH – protects NF membranes from cavitation bubbles. Radially split casing allows quick cleaning of sulfate scale deposits on impeller surfaces, reducing maintenance downtime by up to 40%.

  • Scenario: FPSO and land‑based large‑scale SRU feed pumps. Matches NF membrane medium‑pressure requirements (15–30 bar). Directly connects to upstream ultrafiltration (UF) pretreatment outlet.

  • Representative Models: Sulzer BBS/BBT‑D series, Westgarth SRU‑dedicated BB2 pump.

  • Key Parameters: Flow 100–5000 m³/h, Head 100–450 m, Design pressure ≤50 bar, Temperature ≤45°C (seawater duty).


2. BB3 (Between Bearing Type 3) – Axially Split, Multistage

Structural Definition (API 610)
Horizontal, axially split casing, multiple impellers arranged in opposed pairs. Bearings at both ends. High structural rigidity.

SRU Adaptability

  • Key Advantage: Multistage pressurisation precisely matches high‑pressure NF membrane demands (30–60 bar). Opposed impeller design balances axial thrust – vibration ≤2.5 mm/s, preventing damage to delicate membrane modules. Wetted parts available in super duplex stainless steel (2507) or Hastelloy, resisting seawater corrosion and sulfate crystal abrasion.

  • Scenario: Deep‑reservoir waterflood SRU high‑pressure feed (high osmotic pressure breakthrough); compact offshore SRU modules (e.g., drilling platforms).

  • Representative Models: Sulzer MSD series, PumpWorks BB3‑HP series.

  • Key Parameters: Flow 50–3200 m³/h, Head 200–2900 m, Design pressure up to 300 bar, Temperature –50 to 200°C.


3. BB5 (Between Bearing Type 5) – Radially Split, Barrel Casing, Multistage

Structural Definition (API 610)
Horizontal barrel casing, radially split internal cartridge. Multistage impellers in series. Bearings at both ends. Designed for severe high‑temperature, high‑pressure service.

SRU Adaptability

  • Key Advantage: Barrel construction absorbs pressure shocks and surge loads – ideal for SRU systems with frequent start‑stop cycles and pressure fluctuations. Smooth flow passages reduce sulfate crystal deposition. Maintenance interval ≥10,000 hours.

  • Scenario: Land‑based refineries, large‑scale oilfield SRU high‑pressure feed pumps. Particularly suitable for pretreated seawater containing trace oil contamination.

  • Representative Models: Sulzer CP series.

  • Key Parameters: Flow 50–1000 m³/h, Head 500–7000 m, Design pressure up to 425 bar.


4. VS1 (Vertically Suspended Type 1) – Vertical Turbine, Multistage Diffuser

Structural Definition (API 610)
Vertically suspended, single‑case, multistage diffuser bowl. Impeller/bowl assembly submerged, connected to above‑grade motor via long drive shaft.

SRU Adaptability

  • Key Advantage: Vertical footprint is only 1/3 of a horizontal pump – ideal for FPSO decks, platforms, and space‑constrained SRU modules. Direct compatibility with seawater lift pumps (also VS1) – reduces piping complexity and fittings.

  • Scenario: Floating SRU pretreatment transfer; small SRU module booster pump.

  • Key Parameters: Flow 50–3500 m³/h, Head 200–1000 m, Wetted parts in duplex stainless steel.


5. VS6 (Vertically Suspended Type 6) – Submersible Direct‑Coupled

Structural Definition (API 610)
Motor and pump directly coupled as a single, fully submerged unit. No long shaft, no intermediate bearings. Single or multistage.

SRU Adaptability

  • Key Advantage: Fully submerged installation prevents sludge settling and clogging in SRU pretreatment basins. IP68 rating for wet offshore environments. No long‑shaft bearings eliminates failure points from sulfate crystal abrasion – maintenance cost reduced by 50%.

  • Scenario: SRU pretreatment basin intake, sludge return, backwash water lift.

  • Key Parameters: Flow 5–2500 m³/h, Head 15–140 m, Wetted parts in super duplex 2507.


API 610 SRU Pump Selection Decision Matrix

API 610 TypeCore SRU ScenarioFlow RangeHead RangeMaterial RequirementKey Advantage
BB2Offshore/onshore SRU medium‑pressure feed, large flow transfer100 – 5000 m³/h100 – 450 mDuplex SSLow NPSH, easy scale cleaning, wide flow coverage
BB3SRU high‑pressure feed, deep reservoir injection50 – 3200 m³/h200 – 2900 mSuper duplex / HastelloyStable high pressure, balanced thrust, high corrosion resistance
BB5Land‑based large SRU, severe duty with pressure shocks50 – 1000 m³/h500 – 7000 mHastelloy C276Shock resistant, high T/P capability, long maintenance interval
VS1Offshore compact SRU, modular installation50 – 3500 m³/h200 – 1000 mDuplex SSSmall footprint, seamless integration with lift pumps
VS6SRU pretreatment intake, backwash lift5 – 2500 m³/h15 – 140 mSuper duplex 2507Submerged anti‑clogging, low maintenance, IP68

SRU Integration with Water Treating Full Process (Continuing from Previous Guides)

To ensure a seamless water treatment chain – Seawater Lift → Pretreatment → SRU → RO (if applicable) – follow these structural alignment principles:

  • Structural compatibility: If seawater lift uses VS1/VS6, the SRU pretreatment stage can use the same type (e.g., VS6 submersible pump directly feeding UF pretreatment, then to BB2/BB3 high‑pressure pump). This reduces piping complexity and installation cost.

  • Precise pressure matching:

    • NF membrane pressure 15–30 bar → select BB2

    • NF membrane pressure 30–60 bar → select BB3

    • Avoid extra booster pumps which introduce sulfate crystallization risk at intermediate pressure drops.

  • Anti‑scaling design:

    • Prefer radially or axially split casings (BB2/BB3/BB5) for easy periodic cleaning of impeller deposits.

    • Specify polished surface finish on wetted parts to reduce sulfate adhesion.

    • For severe scaling, consider coated impellers (e.g., electroless nickel or ceramic).

  • Compliance & chemical compatibility:

    • All SRU pumps must meet API 610 12th Edition, ISO 13709.

    • Materials must be compatible with SRU chemicals (anti‑scalants, non‑oxidising biocides, membrane cleaning chemicals). Super duplex 2507 and Hastelloy C276 are preferred for aggressive seawater + chemical environments.

For engineering assistance, detailed pump sizing, or a quotation for any API 610 SRU pump (BB2, BB3, BB5, VS1, VS6), please contact info@hyrig.com. We respond within 24 hours.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit