This page presents verified field cases of our API 610 BB4 horizontal multistage between-bearings pumps operating in ultra high head, high pressure, and high temperature continuous duty. Each case demonstrates the pump's ability to deliver reliable performance in the most demanding industrial applications.
Case 1 – Power Plant Boiler Feed Project (Asia)
Background: A 350 MW supercritical coal-fired power plant required a high-pressure boiler feed pump capable of meeting full load operation with high efficiency and long-term stability.
BB4 Pump Solution:
Flow: 420 m³/h
Head: 1,350 m
Temperature: 210°C
Casing: Barrel type
Material: Carbon steel casing, stainless steel impeller
Seal: API 682 Plan 23 mechanical seal
Results:
High lift and high pressure perfectly matched boiler full load operation
Long-term stable running – over 3 years without unplanned downtime
High efficiency (82%) provided measurable energy savings
Centerline mounting eliminated thermal misalignment during start-up and load changes
Available references: Site photo, performance test report, efficiency log.
Case 2 – Oilfield High Pressure Water Injection (Middle East)
Background: An oilfield operator needed a high-pressure water injection pump for a deep well secondary recovery project. The pump had to deliver stable pressure at extreme depths with minimal maintenance.
BB4 Pump Solution:
Flow: 320 m³/h
Head: 1,800 m
Discharge pressure: 175 bar
Material: 316L stainless steel (for produced water compatibility)
Seal: API 682 Plan 53B dual cartridge seal
Lubrication: Forced feed oil system
Results:
Stable pressure output maintained within ±1.5% across 2 years of operation
Low maintenance rate – only routine bearing and seal inspection annually
Barrel casing safely contained ultra high pressure
Wear-resistant impeller stages showed minimal erosion
Available references: Site installation photo, pressure trend log, maintenance record.
Case 3 – Refinery Hydrogenation Process (Southeast Asia)
Background: A refinery required a high-pressure feed pump for a diesel hydrotreating unit (hydrogenation). Operating conditions: high temperature, high pressure, hydrogen-rich sour service requiring NACE compliance.
BB4 Pump Solution:
Flow: 180 m³/h
Head: 1,200 m
Temperature: 260°C
Pressure: 110 bar
Material: Alloy steel casing, 17-4PH impeller, NACE MR0175 compliant
Seal: Dry gas seal (for hydrogen service)
Results:
Withstood high temperature and high pressure without deformation
Met strict refinery process standards for leak-free hydrogen containment
Dry gas seal provided zero emissions – critical for hydrogen safety
Continuous operation for 18 months, still running reliably
Available references: P&ID, NACE compliance certificate, site photo.
Case 4 – Seawater Desalination High Pressure RO (Middle East)
Background: A large-scale seawater reverse osmosis (SWRO) desalination plant needed a high-pressure feed pump with exceptional corrosion resistance for 24/7 operation in aggressive chloride environment.
BB4 Pump Solution:
Flow: 650 m³/h
Head: 680 m
Pressure: 72 bar
Material: Super duplex stainless steel (casing, impeller, shaft)
Seal: API 682 Plan 53B with seawater-compatible faces
Results:
No corrosion or pitting after 2+ years in high chloride seawater
Stable high pressure output supported consistent membrane performance
Long-term desalination system operation with minimal downtime
High efficiency reduced energy cost by 6% compared to previous pump
Available references: Site photos, material certificate (EN 10204 3.1), operating report.
What You Can Request From Us for Each Case
Site photos and installation images
Project parameter sheet (flow, head, pressure, material, seal)
Actual running data (pressure, vibration, bearing temperature, power consumption)
User reference contact (with prior permission)
Why Real Project Cases Matter
Field references prove that our BB4 pumps deliver:
Ultra high head and pressure for boiler feed and water injection
Long-term stability in power plant and refinery service
Corrosion resistance for desalination (duplex, super duplex)
Low maintenance and high reliability for 24/7 continuous duty
Get the Complete BB4 Pump Case Study Package
We can match your operating conditions to similar successful installations. Request the BB4 pump project case PDF or ask for references in your specific industry.
Email: info@hyrig.com
Please specify your industry (power plant / oilfield / refinery / desalination) and we will send relevant case studies, photographs, and technical data within 24 hours. We also welcome inquiries for custom BB4 pump selection and factory direct wholesale pricing.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.