HYRIG can supply the BM2 series hydraulic motors range. The BM2 is a medium-duty, spool valve type motor that can bear higher pressure than the BM1 series, featuring a gerotor design for higher efficiency in medium load applications.
With displacements ranging from 50 ml/r to 500 ml/r, the BM2 series offers a reliable and efficient solution for various hydraulic drive systems. The credible shaft seal design allows it to be used in parallel or in series. This series also includes the BM2W wheel motor (with radial bearings for higher side loads) and the BM2B brake motor (with an integrated hydraulic brake).
Data source: Technical data table
| Displacement (ml/r) | Flow Cont. (LPM) | Speed Cont. (RPM) | Pressure Cont. (MPa) | Torque Cont. (N·m) |
|---|---|---|---|---|
| 50 | 40 | 755 | 14 | 100 |
| 63 | 40 | 630 | 14 | 124 |
| 80 | 60 | 750 | 17.5 | 190 |
| 100 | 60 | 600 | 17.5 | 240 |
| 125 | 60 | 475 | 17.5 | 292 |
| 160 | 60 | 375 | 16.5 | 363 |
| 200 | 60 | 300 | 13 | 358 |
| 250 | 60 | 240 | 11 | 352 |
| 315 | 60 | 190 | 8.5 | 360 |
| 400 | 60 | 160 | 8 | 420 |
| 500 | 60 | 110 | 8 | 464 |
Note: Continuous data refers to the max value of operating motor continuously. A simultaneous max RPM and max pressure is not recommended.
The BM2W is a wheel motor variant featuring a radial bearing that can bear a larger radial force. It shares the same main specifications and performance data as the standard BM2, making it ideal for direct wheel drive applications.
The BM2B is designed with a brake device, shuttle valve, and internal control oil loop. It has a compact design and is easy to install, making it suitable for building, shipping, crane, mining, and metallurgy applications.
The BM2 series is available with various flange and shaft combinations to match your specific mounting requirements. Please refer to the ordering information for exact dimensions.
| Shaft Type | Description |
|---|---|
| Shaft A | Cylindrical shaft: Φ25x40, parallel key: 8x7x32, link thread: 1/4-20UNC |
| Shaft B | Cylindrical shaft: Φ25x43, parallel key: 8x7x32, link thread: M8 |
| Shaft C | Cylindrical shaft: Φ32x56, parallel key: 10x8x45, link thread: M8 |
When replacing an older BM2 or equivalent motor, verify the following:
The BM2 series is widely used in:
Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation.
Need a specific displacement or a brake/wheel variant? Explore the individual models: BM2-100 Hydraulic Motor, BM2-200 Hydraulic Motor, or contact us for a custom configuration.
Q: What is the maximum continuous pressure of the BM2 series?
The BM2 series can handle a maximum continuous pressure of up to 17.5 MPa (for the 80-125 ml/r models).
Q: What is the difference between BM2 and BM2W?
The BM2W features an additional radial bearing designed to handle high side loads, making it suitable for direct wheel drive applications.
Q: Can I use the BM2B brake motor in dynamic braking?
No, the brake should be applied in a static state. Dynamic braking is not permitted.
For BM2 series hydraulic motor selection, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.